 | Copyright © 2008, Juniper Networks, Inc. All rights reserved. Trademark Notice. | |
You can configure the Fast Ethernet management port to access the router from a Telnet session or SNMP.
On ERX-7xx models, ERX-14xx models, and ERX-310 routers, the Fast Ethernet port is located on the SRP I/O module. For more information about configuring the Fast Ethernet port on an SRP I/O module, see ERX Hardware Guide, Chapter 7, Accessing ERX Routers.
Use the Fast Ethernet port on the SRP I/O module only as a router management port. Do not use this port to route traffic for Fast Ethernet or higher-level protocols such as transport or routing protocols, because doing so affects the performance of the router.
On the E120 router and the E320 router, the Fast Ethernet port is located on the SRP IOA. For more information about configuring the Fast Ethernet port on an SRP IOA, see E120 and E320 Hardware Guide, Chapter 7, Accessing E-Series Routers.
interface fastEthernet
- host1(config)#interface fastEthernet 0/0
- host1(config)#interface fastEthernet 6/0/0
You can set a baseline and view statistics on the Fast Ethernet port of the SRP module in the same way that you would for other Ethernet interfaces. See JUNOSe Physical Layer Configuration Guide.
Slots 0 and 1 are reserved for SRP modules on ERX-7xx models; slots 6 and 7 are reserved for SRP modules on ERX-14xx models, the E120 router, and the E320 router. When you configure the Fast Ethernet interface on an SRP module, the output of the show configuration command always indicates that the interface is configured in the lower of the two slots (slot 0 or slot 6). This indication is true if you configure the interface on a redundant SRP module in the higher slot or even if you have only one SRP module and it is installed in the higher slot, as shown in the following example:
host1#show version
Juniper Edge Routing Switch ERX-700
Copyright (c) 1999-2005 Juniper Networks, Inc. All rights reserved.
System Release: erx_7-1-0.rel Partial
Version: 7.1.0 [BuildId 4518] (December 21, 2005 11:23)
System running for: 25 days, 3 hours, 31 minutes, 5 seconds
(since THU DEC 22 2005 11:36:41 UTC)
slot state type admin spare running release slot uptime ---- ------- ---------- ------- ----- ------------------ -------------- 0 standby SRP-10Ge enabled --- erx_7-1-0.rel --- 1 online SRP-10Ge enabled --- erx_7-1-0.rel 25d03h:28m:49s 2 --- --- --- --- --- --- 3 --- --- --- --- --- --- 4 online CT3-12 enabled --- erx_7-1-0.rel 25d03h:24m:46s 5 online OC3-4A-APS enabled --- erx_7-1-0.rel 25d03h:24m:22s 6 online GE enabled --- erx_7-1-0.rel 25d03h:24m:44s
host1#configure terminal Enter configuration commands, one per line. End with ^Z. host1(config)#interface fastethernet 0/0 host1(config-if)#ip address 10.6.130.83 255.255.128.0 host1(config-if)#exit host1(config)#ip route 0.0.0.0 0.0.0.0 10.6.128.1 host1(config)#exit host1#show config ! Configuration script being generated on TUE SEP 14 2004 13:22:06 UTC ! Juniper Edge Routing Switch ERX-700 ! Version: 6.0.0 beta-1.8 [BuildId 2538] (September 7, 2004 12:46) ! Copyright (c) 1999-2004 Juniper Networks, Inc. All rights reserved. ! ! Commands displayed are limited to those available at privilege level 10 ! boot config running-configuration boot system erx_6-0-0b1-8.rel no boot backup no boot subsystem no boot backup subsystem no boot force-backup ! ! Note: The following commands are here to ensure that all virtual routers and ! vrfs are created before other commands that may need to reference them. ! These commands will be repeated further on as each virtual router and vrf ! has its configuration presented. ! virtual-router default virtual-router vr8 ! ! hostname "host1" exception protocol ftp anonymous null ! controller t3 2/0 [...] ! interface fastEthernet 0/0 ip address 10.6.130.83 255.255.128.0 ! ip route 0.0.0.0 0.0.0.0 10.6.128.1 ! Trap Source: <not configured> ! Note: SNMP server not running. !
| Copyright © 2008, Juniper Networks, Inc. All rights reserved. Trademark Notice. | |