[Contents] [Prev] [Next] [Report an Error]

OC48/STM16 POS IOA

IOA label ES2-S1 OC48 STM16 POS IOA

Number of IOA ports

1

Software release

First supported: 7.0.1

Description

30 W

Half-height module

See Module and Slot Combinations for more information on combining IOAs in a slot.

Unchannelized, concatenated OC48/STM16 for POS

Capability

OC48/STM16

HDLC framing

Software features

See OCx/STMx POS IOAs for information about the layer 2 and layer 3 protocols and applications that this module combination supports.

Model compatibility

E320 router

E120 router

Line module compatibility

ES2 4G LM

SRP module compatibility

SRP-100

SRP-120

SRP-320

Line module redundancy compatibility

Can be paired with an ES2 4G LM.

Must be installed in the same redundancy group as an ES2 4G LM and ES2–S1 REDUND IOA combination.

Module redundancy support

Yes (Redundancy IOA must be installed in either slot 0 or slot 11)

Port redundancy support

Not applicable

Cables and connectors (single-mode short reach [SR-1])

Up to one LC full duplex connector

Transmit power:

min: –10 dBm

max: –3 dBm

Center wavelength: 1310 nm

Receive input power:

min: –18 dBm

max: –3 dBm

Rated for 2 km (1.2 miles) of 9-micron core cable

See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.

Cables and connectors (single-mode intermediate [IR-1])

Up to one LC full duplex connector

Transmit power:

min: –5 dBm

max: 0 dBm

Center wavelength: 1266 through 1310 nm

Receive input power:

min: –18 dBm

max: –0 dBm

Rated for 15 km (9.3 miles) of 9-micron core cable

See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.

Cables and connectors (single-mode long reach [LR-2])

Up to one LC full duplex connector

Transmit power:

min: –2 dBm

max: 3 dBm

Center wavelength: 1550 through 1580 nm

Receive input power:

min: –28 dBm

max: –9 dBm

Rated for 80 km (24.9 miles) of 9-micron core cable

See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.

LEDs Board-level LEDs:

OK (green)—Physical link is connected properly and is functioning properly

FAIL (red)—Failure detected

Port LEDs:

ALM—Bi-color LED:

Yellow: Local loss of signal exists

Red: Remote loss of signal exists

OK (green)—SONET is up and port is functioning properly. If not lit, a problem exists.

Alarms, errors, and events

See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.

[Contents] [Prev] [Next] [Report an Error]

IOA label	ES2-S1 OC48 STM16 POS IOA
Number of IOA ports	1
Software release	First supported: 7.0.1
Description	30 W Half-height module See Module and Slot Combinations for more information on combining IOAs in a slot. Unchannelized, concatenated OC48/STM16 for POS
Capability	OC48/STM16 HDLC framing
Software features	See OCx/STMx POS IOAs for information about the layer 2 and layer 3 protocols and applications that this module combination supports.
Model compatibility	E320 router E120 router
Line module compatibility	ES2 4G LM
SRP module compatibility	SRP-100 SRP-120 SRP-320
Line module redundancy compatibility	Can be paired with an ES2 4G LM. Must be installed in the same redundancy group as an ES2 4G LM and ES2–S1 REDUND IOA combination.
Module redundancy support	Yes (Redundancy IOA must be installed in either slot 0 or slot 11)
Port redundancy support	Not applicable
Cables and connectors (single-mode short reach [SR-1])	Up to one LC full duplex connector Transmit power: min: –10 dBm max: –3 dBm Center wavelength: 1310 nm Receive input power: min: –18 dBm max: –3 dBm Rated for 2 km (1.2 miles) of 9-micron core cable See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
Cables and connectors (single-mode intermediate [IR-1])	Up to one LC full duplex connector Transmit power: min: –5 dBm max: 0 dBm Center wavelength: 1266 through 1310 nm Receive input power: min: –18 dBm max: –0 dBm Rated for 15 km (9.3 miles) of 9-micron core cable See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
Cables and connectors (single-mode long reach [LR-2])	Up to one LC full duplex connector Transmit power: min: –2 dBm max: 3 dBm Center wavelength: 1550 through 1580 nm Receive input power: min: –28 dBm max: –9 dBm Rated for 80 km (24.9 miles) of 9-micron core cable See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
LEDs	Board-level LEDs: OK (green)—Physical link is connected properly and is functioning properly FAIL (red)—Failure detected Port LEDs: ALM—Bi-color LED: Yellow: Local loss of signal exists Red: Remote loss of signal exists OK (green)—SONET is up and port is functioning properly. If not lit, a problem exists.
Alarms, errors, and events	See Monitoring SONET/SDH Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 3, Configuring Unchannelized OCx/STMx Interfaces.