[Contents] [Prev] [Next] [Index] [Report an Error] [No Frames]

JUNOSe 9.1.x System Basics Configuration Guide > Passwords and Security > Setting and Erasing Passwords

Setting and Erasing Passwords

You can set the following passwords:

Privilege Levels

Different groups of commands are associated with privilege levels (Table 51). You can set enable passwords to allow users to access commands at different privilege levels.





 Table 51:  Commands Available at Different Privilege Levels  


 Privilege Level


 Commands Available




 0



 help, exit, enable, and disable commands





 1



 User Exec commands plus commands at level 0





 5



 Privileged Exec show commands plus commands at levels 0 and 1





 10



 All commands except support commands





 15



 Support commands that Juniper Networks Technical Support may provide and all other commands

To maximize security and usability, set different passwords for levels 1, 5, 10, and 15. By default, no enable passwords exist.

Accessing Privilege Levels

If users have access to the console, they automatically have access to privilege level 0. To access higher levels of privilege, they must enter the enable privilege-level command. When users specify a privilege level, the system determines whether there is a password at that level. If there is not, the system prompts the user for the password for the lower level closest to the requested level.

Setting Enable Passwords

To set up enable passwords, use the commands described in Setting Basic Password Parameters.

Erasing Enable Passwords

If you forget an enable password or secret, you can erase all enable passwords and secrets.

Two commands allow you to erase passwords and secrets: erase secrets and service unattended-password-recovery. It is important to fully understand the purpose of these commands and how they work with each other.

The erase secrets command can be used to delete all existing passwords. To use this command, you must be physically present at the router to complete the operation. After the command has been executed, you have a finite number of seconds to press the software reset button on the SRP module. You can execute this command from the console or any vty.

The service unattended-password-recovery command provides you with a way to delete existing passwords and secrets without physically being present at the router. You must have the proper privilege level to execute the command, and you can execute it from either the console or any vty.

When you execute service unattended-password-recovery, you change the behavior of erase secrets. You can now delete passwords and secrets from the console by executing erase secrets without a time restraint or having to be physically present at the router. When you use the no version of service unattended-password-recovery, you revert the functionality of erase secrets to the factory default setting.

To erase all enable passwords or secrets:

  1. Log in to the router.
  2. Erase the existing enable password or secret. Specify the number of seconds to allow for the erase operation.
    3. host1>erase secrets 60
  3. Within the time limit that you specified for the erase secrets command, press the recessed software reset button on the primary SRP module (see Figure 28).

Figure 28: Location of the Software Reset Button


 





 NOTE: If you do not press the software reset button within the time limit, the system will not erase the password, and you will need to repeat the process.

erase secrets

service unattended-password-recovery

Setting a Console Password

By default, there is no console password. To set a console password:

  1. Make sure that you know the enable password for the system.

If you need to reset the enable password, see Privilege Levels.

  1. Access Privileged Exec mode, and enter the enable password if prompted.
  2. Access Global Configuration mode.
  3. Access Line Configuration mode.
    4. host1(config)#line console 0
  4. Enable password checking at login.
    5. host1(config-line)#login
  5. Specify a password.
    6. host1(config-line)#password 7 dq]XG`,%N"SS7d}o)_?Y

line

login

password

Erasing the Console Password

If you forget the console password, you can erase the existing value and configure a new one. This action deletes all authentication for the console line. To erase existing passwords:

  1. Reboot the router by pressing the recessed software reset button on the primary SRP module (see Figure 28) and then pressing the mb key sequence during the countdown.
  2. Disable authentication at the console level.
    3. :boot##disable console authentication

If you remember the password at this point, you can override this action by entering:

:boot##no disable console authentication
  1. Reload the operating system.
    2. :boot##reload

When the operating system reloads, you can access the console without a password.

NOTE: You will be able to log in to the console without a password until you set a new password.

Monitoring Passwords

You can use the show secrets command to view all current passwords and secrets.

show secrets

[Contents] [Prev] [Next] [Index] [Report an Error] [No Frames]