JUNOSe 9.1.x IP, IPv6, and IGP Configuration Guide > Configuring RIP > Monitoring RIP

Monitoring RIP

Two sets of commands enable you to monitor RIP operation on your router: the debug and the show commands. Both sets of commands provide information about your router's RIP state and configuration.

The task you are performing with each of these monitoring commands is basically the same for each command; that is, you are requesting information. The results of this request may vary. For instance, the debug commands provide information about problems with the network or the router, whereas the show commands provide information about the actual state and configuration of your router.

debug Commands

The debug commands provide information about the following RIP items:

• General events, such as creating a RIP process or removing RIP from an interface
• Routing events, such as when two RIP routers exchange routes

debug ip rip

• Use to display information about selected RIP events. This command has many keywords that allow you to specify a variety of RIP events.
• You can set the level of severity for the events you want displayed; specify the desired descriptive term or a corresponding number (0–7).
• You can set the verbosity of the messages you want displayed: low, medium, high.
• Example

host1#debug ip rip events

• Use the no version to cancel the display of any information about the designated variable.

undebug ip rip

• Use to cancel the display of information about a selected event.
• The same RIP variables can be designated as in the debug ip rip command.
• Example

host1#undebug ip rip events

• There is no no version.

show Commands

Use the show commands to monitor the following types of RIP information:

• Configuration
• IP-related information
• Global counters
• Counters for a specified network
• Statistics

You can set a statistics baseline for RIP interfaces by using the baseline ip rip command.

You can specify a VRF instance for the show ip rip commands. You can use the output filtering feature of the show command to include or exclude lines of output based on a text string you specify. See JUNOSe System Basics Configuration Guide, Chapter 2, Command-Line Interface, for details.

baseline ip rip

• Use to set a statistics baseline for RIP interfaces.
• The router implements the baseline by reading and storing the statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved.
• Use the optional delta keyword with the show ip rip statistics command to specify that baselined statistics are to be shown.
• Example

host1#baseline ip rip

• There is no no version.

show ip rip

• Use to display RIP information.
• Specify vrf vrfName to limit the display to a specific VRF.
• Use the ifconfig keyword to display address and interface configuration information instead of the default operational data.
• Field descriptions

• Router Information Protocol Fields

• Router Administrative State—Displays the RIP state. Enable means the router is allowed to send and receive updates. Disable means that RIP might be configured but it is not allowed to run yet.
• System version RIP1—RIP versions allowed for sending and receiving RIP updates. The router version is currently set to RIP1, which sends RIPv1 but will receive RIPv1 or RIPv2. If it is set to RIP2, it will send and receive RIPv2 only. The default is configured for RIP1.
• Incoming filters—Access list applied to incoming route updates
• Outgoing filters—Access list applied to outgoing route updates
• Global route map—Route map that specifies all RIP interfaces on the router
• Default metric—Value for redistributed routes. The default is 1. This global value is superseded by metrics applied to a RIP interface.
• Distance—Value added to RIP routes added to the IP routing table. The default is 120.
• Number of route changes—Number of times the router has been told to route changes by its peers
• Number of route queries—Number of times the router has received route requests from other routers
• Update interval—Current setting of the update timer (in seconds)
• Invalid interval—Current setting of the invalid timer (in seconds)
• Hold down time—Current setting of the hold-down timer (in seconds)
• Flush interval—Current setting of the flush timer (in seconds)
• Route Type—Whether RIP routes are available only for unicast forwarding, only for multicast reverse path forwarding checks, or for both
• Max Ecmp Paths—Number of parallel routes that RIP can support
• Default-Information originate always—Ability (enabled or disabled) of RIP to advertise a default route (0.0.0.0/0) if the default route exists in the IP routing table
• Triggered Updates—Ability (enabled or disabled) of RIP to send triggered updates
• Purge Routes on Interface Down Event—Ability (enabled or disabled) of RIP to purge the routing table for interfaces that were brought down by some event
• Send More Specific Routes—Ability (enabled or disabled) of RIP to send a less-specific route in preference to a more-specific route if the less-specific route has a metric
• Debounce Time—Debounce time for interfaces brought down by some event
• Default-Information originate—Ability (enabled or disabled) of RIP to advertise a default route (0.0.0.0/0) if the default route exists in the IP routing table
• route-map—Name of the route map specified for RIP
• Summary Address—Route that RIP summarizes
• Network—IP address of a network on which RIP is running
• Netmask—Network mask applied to the network address
• Neighbor—Configured neighbor information

• Address Operational Data

• Unnumbered status—Status of the unnumbered interface
• Received bad packet—Number of bad packets received
• Received bad routes—Number of bad routes received
• Triggered updates sent—Number of triggered updates sent; triggered updates are sent before the entire RIP routing table is sent; triggered by events such as adding a new RIP route or redistribution
• Received updates—Number of updates received
• Numbered status—Status of the numbered interface from which this interface obtains its configuration
• Send version—Version of RIP used for sending updates
• Receive version—Version of RIP accepted in received updates
• Authentication mode—Password or MD5 authentication, or none
• Default metric—Metric value applied to the RIP interface. The default
  is 1.
• BFD minimum receive interval(msec)—Configured minimum interval requested between BFD control packets sent by the remote RIP peer; used with RIP peers to negotiate a detection interval for BFD session failure. The default is 300 milliseconds.
• BFD minimum transmit interval(msec)—Configured minimum interval between BFD control packets sent by the local RIP peer; used with RIP peers to negotiate a detection interval for BFD session failure. The default is 300 milliseconds.
• BFD multiplier—Multiplied by the negotiated BFD minimum receive interval to determine the interval between packets permitted before the BFD session is declared down. Also, the number of BFD control packets that the RIP local peer can miss before the BFD session is declared down. The default is 3.
• Passive Interface—Whether or not the interface is passive, thereby restricting the interface to unicast RIP messages
• Passive Interface—Whether or not the interface is passive, thereby restricting the interface to unicast RIP messages
• Access-list applied to outgoing route—Name of the access list applied to outgoing routes
• Access-list applied to incoming route—Name of the access list applied to incoming routes
• Route-map applied to outgoing route—Name of the route map applied to outgoing routes

• Example 1

host1#show ip rip

Routing Information Protocol

 Router Administrative State = enable 

 System version RIP2: send = 2, receive = 2 

 No filter is applied to outgoing route update for all interfaces

 No filter is applied to incoming route update for all interfaces

 No global route map

 No table map

 Default metric = 1

 Distance = 120

 Number of route changes = 3

 Number of route queries = 0

 Update interval = 30 (secs)

 Invalid interval = 180 (secs)

 Hold down time = 120 (secs)

 Flush interval = 300 (secs)

 Route Type     =  both unicast and multicast

 Max Ecmp Paths = 4

 Default-Information originate always = enabled

 Triggered Updates = enabled

 Purge Routes on Interface Down Event  = enabled

 Send More Specific Routes  = enabled

 Debounce Time = 10

 Default-Information originate : disabled

     route-map :  none

  Summary Address:  None

 Network         netmask

  Neighbor

    No Configured Neighbors

          *** Address Operational Data ***

Unnumbered, Rip is up, ATM2/1.18

  Dynamic creation and inherits configuration from loopback1

  Received bad packet = 0

  Received bad routes = 0

  Triggered updates sent = 0

  Received updates = 9

1.1.1.1, Rip is up, loopback1

  Send version = 2

  Receive version = 2

  Authentication mode = none

  Default metric = 1

  Passive Interface = No

  Access-list applied to outgoing route = none

  Access-list applied to incoming route = none

  Route-map applied to outgoing route = none

  Copy configuration to dynamic interfaces

  Received bad packet = 0

  Received bad routes = 0

  Triggered updates sent = 0

  Received updates = 0

• Example 2

host1#show ip rip ifconfig

Routing Information Protocol

 Router Administrative State = enable 

 System version RIP2: send = 2, receive = 2 

 No filter is applied to outgoing route update for all interfaces

 No filter is applied to incoming route update for all interfaces

 No global route map

 No table map

 Default metric = 1

 Distance = 120

 Number of route changes = 17

 Number of route queries = 2

 Update interval = 30 (secs)

 Invalid interval = 180 (secs)

 Hold down time = 120 (secs)

 Flush interval = 300 (secs)

 Route Type     =  both unicast and multicast

 Max Ecmp Paths = 4

 Default-Information originate always = enabled

 Triggered Updates = enabled

 Purge Routes on Interface Down Event  = enabled

 Send More Specific Routes  = enabled

 Debounce Time = 10

 Default-Information originate : disabled

     route-map :  none

  Summary Address:  None

 Network         netmask

  Neighbor

    No Configured Neighbors

          *** Interface Configuration Data***

loopback1

  Send version = def

  Receive version = def

  Authentication mode = none

  Default metric = default

  Passive Interface = No

  Access-list applied to outgoing route = none

  Access-list applied to incoming route = none

  Route-map applied to outgoing route = none

  Copy configuration to dynamic interfaces

          *** Address Configuration Data ***

Unnumbered, Rip is up, ATM2/1.18

  Dynamic creation and inherits configuration from loopback1

  Received bad packet = 0

  Received bad routes = 0

  Triggered updates sent = 0

  Received updates = 3

1.1.1.1, Rip is up, loopback1

  Send version = def

  Receive version = def

  Authentication mode = none

  Default metric = default

  Passive Interface = No

  Access-list applied to outgoing route = none

  Access-list applied to incoming route = none

  Route-map applied to outgoing route = none

  Received bad packet = 0

  Received bad routes = 0

  Triggered updates sent = 0

  Received updates = 0

• Example 3—Interface configuration data excerpt showing BFD information.

host1#show ip rip ifconfig

...

*** Interface Configuration Data***

FastEthernet1/0

  Send version = def

  Receive version = def

  Authentication mode = none

  Default metric = default

  BFD minimum receive interval(msec) =  400

  BFD minimum transmit interval(msec)= 500

  BFD multiplier = 2

  Passive Interface = No

  Access-list applied to outgoing route = none

  Access-list applied to incoming route = none

  Route-map applied to outgoing route = none

show ip rip brief

• Use to display limited RIP information.
• Specify vrf vrfName to limit the display to a specific VRF.
• Field descriptions

• IP Address—IP address of the interface where RIP is running
• Tx—Transmit version of RIP on this interface, which can override the router configuration
• Rx—Receive version of RIP on this interface
• Auth—Type of authentication, password (text) or MD5
• Met—Current value is the same as the router one (the default metric). Based on MIB 2 for RIP, the interface's route metric can be set individually.
• AccList O/I—Access list applied to outgoing/incoming RIP route updates
• RtMap—Identifier for the route map that specifies a summary of RIP routes
• Status—Status of RIP, either up or down
• Intf—Interface type on which RIP is running

• Example

host1#show ip rip brief

IP Address Tx  Rx  Auth  Met AccList O/I  RtMap Status Intf

10.2.1.32  1   1,2 none  1   no/no   no   up    fastEthernet0/0   

10.10.1.2  1   1,2 none  1   no/no   no   up    serial5:1/1:1

show ip rip database

• Use to display the route entries in the RIP routing table.
• Specify vrf vrfName to limit the display to a specific VRF.
• Specify the active keyword to limit the display to active routes learned via RIP updates.
• Specify the inactive keyword to limit the display to routes that the router will discard in the immediate future.
• Field descriptions

• Prefix—IP address prefix
• Length—Prefix length
• ttl—(Time to live) Indicates how many seconds the specific route remains in the routing table. If an entry reaches 0, it is removed from the routing table.
• Met—Metric that RIP uses to rate the value of different routes (hop count). The hop count is the number of routers that can be traversed in a route.
• Next Hop—Next IP address where a packet is sent. A value of zero in this field indicates that the next address the packet should be sent to is the router that originally sent the RIP message.
• Intf—Interface that the route has learned

• Example

host1#show ip rip database

Prefix/Length: ttl  Met:  Next Hop       Intf:

3.0.0.0/8      0    1     72.30.100.2    tm2/1.100

9.20.0.0/17    0    2     172.30.100.1   tm2/1.100

10.2.1.0/24    0    2     172.30.100.1   tm2/1.100

show ip rip network

• Use to display the networks associated with the RIP routing process.
• Specify vrf vrfName to limit the display to a specific VRF.
• Field descriptions

• network—IP address of a network on which RIP is running
• netmask—Network mask applied to the network address

• Example

host1#show ip rip network

Network         netmask

 10.2.1.0       255.255.255.0

 172.30.100.0   255.255.255.0

 172.30.200.0   255.255.255.0 

show ip rip peer

• Use to display limited information about each RIP neighbor.
• Specify vrf vrfName to limit the display to a specific VRF.
• Field descriptions

• Time since last update received—Time in seconds since an update was received from this peer
• Peer version—Version of IS-IS running on the peer
• Bad packets received—Number of bad packets received from the peer
• Bad routes received—Number of bad routes received from the peer
• BFD—State of the BFD session with the peer, Up or Down

• Example

host1#show ip rip peer

192.168.1.102

   Time since last update received = 24

   Peer version = 1

   Bad packet received = 0

   Bad routes received = 0

   BFD Up

192.168.1.151

   Time since last update received = 24

   Peer version = 1

   Bad packet received = 0

   Bad routes received = 0

   BFD Down

192.168.1.250

   Time since last update received = 7

   Peer version = 2

   Bad packet received = 0

   Bad routes received = 0

   BFD Up

show ip rip statistics

• Use to display global and session statistics counters for RIP. If you specify an IP address, statistics for that interface are displayed in addition to the global RIP statistics.
• Specify vrf vrfName to limit the display to a specific VRF.
• Use the optional delta keyword to specify that baselined statistics are to be shown. You must use the baseline ip rip command to set a baseline.
• Field descriptions

• Number of route changes—Number of times the router has been told to route changes by its peers
• Number of route queries—Number of times the router has received route requests from other routers
• Received bad packets—Number of bad packets received from the peer
• Received bad routes—Number of bad routes received from the peer
• Triggered updates sent—Number of triggered updates sent; triggered updates are sent before the entire RIP routing table is sent; triggered by events such as adding a new RIP route or redistribution
• Received updates—Number of updates received

• Example 1

host1#show ip rip statistics

 Number of route changes = 23

 Number of route queries = 0

• Example 2

host1#show ip rip statistics 10.2.1.32

Number of route changes = 901

Number of route queries = 0

fastEthernet 0/0, 10.2.1.32

  Received bad packet = 0

  Received bad routes = 0

  Triggered updates sent = 2

  Received updates = 41

show ip rip summary-address

• Use to display the specified summary address or all summary addresses for RIP.
• Field descriptions

• Summary Address—Address summarizing RIP routes
• Mask—Network mask specified in the ip summary-address command to identify which routes to summarize
• Metric—Metric advertised with the summary RIP prefix

• Example

host1#show ip rip summary-address

Summary Address Mask            Metric

 4.3.0.0         255.255.0.0     3

 4.4.0.0         255.255.0.0     5