10GE PR IOA

IOA label	ES2-S2 10GE PR IOA
Number of IOA ports	2 1 active, 1 redundant
Software release	First supported: 7.2.0
Description	40 W Full-height module Uses a range of 10-gigabit small form-factor pluggable (XFP) transceivers to support different modes and cable lengths. Pairs only with ES2 10G UPLINK LM and ES2 10G LM to provide 10-Gigabit Ethernet operation through a single line interface Router can accommodate up to two ES2 10G UPLINK LM and ES2-S2 10GE PR IOA combinations In a 100 Gbps configuration, the router can accommodate up to two ES2 10G LM and ES2-S2 10GE PR IOA combinations In a 320 Gbps configuration, the router can accommodate up to twelve ES2 10G LM and ES2-S2 10GE PR IOA combinations
Capability	Ethernet (IEEE 802.3ae) 10Gb Base-SR/LR/ER Port can operate in full duplex mode with an average data rate of 10 Gbps
Software features	See Ethernet IOAs for information about the layer 2 and layer 3 protocols and applications that this module combination supports.
Model compatibility	E320 router E120 router
Line module compatibility	ES2 10G UPLINK LM ES2 10G LM
SRP module compatibility	SRP-100 SRP-120 SRP-320
Line module redundancy compatibility	Not applicable
Port redundancy support	Yes
Cables and connectors (multimode [SR])	One LC full duplex connector Transmit power: min: –7.3 dBm max: –1.0 dBm Receive input power: min: –9.9 dBm max: –1.0 dBm See the following corresponding table (SR Fiber Optic Cabling) for cabling requirements. See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
Cables and connectors (single-mode [LR])	One LC full duplex connector Transmit power: min: –8.2 dBm max: 0.5 dBm Receive input power: min: –14.4 dBm max: 0.5 dBm See the following corresponding table (LR Fiber Optic Cabling) for cabling requirements. See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
Cables and connectors (single-mode [ER])	One LC full duplex connector Transmit power: min: –4.7 dBm max: 4.0 dBm Receive input power: min: –15.8 dBm max: –1.0 dBm See the following corresponding table (ER Fiber Optic Cabling) for cabling requirements. See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
LEDs	Board-level LEDs: OK (green)—IOA online and is functioning properly FAIL (red)—Failure detected Port LEDs: LK (green)—Ethernet link is up ACT (green)—Blinks when Ethernet traffic is being received Port labels: W—Working port P—Protect port (LK blinks when active cable is attached even though it is not the active working port)
Alarms, errors, and events	See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.

Table 20: SR Fiber Optic Cabling

Fiber Type	Minimal Modal Bandwidth at 850 nm (MHz*km)	Maximum Operating Range (meters)
62.5 microns	160	26 (85.3 ft)
	200	33 (108.27 ft)
50 microns	400	66 (216.54 ft)
	500	82 (269.03 ft)
	2000	300 (984.25 ft)

Table 21: LR Fiber Optic Cabling

Fiber Type	Nominal Wavelength (nm)	Maximum Operating Range (kilometers)
9 microns	1310	10 (6.2 miles)

Table 22: ER Fiber Optic Cabling

Fiber Type	Nominal Wavelength (nm)	Maximum Operating Range (kilometers)
9 microns	1550	40 (24.85 miles)

Copyright © 2008, Juniper Networks, Inc. All Rights Reserved. Trademark Notice.