Detecting Peer Reachability with BFD

You can configure a Bidirectional Forwarding Detection (BFD) session with a BGP neighbor or peer group to determine relatively quickly whether the neighbor or peer group is reachable. For more information on BFD, see JUNOSe IP Services Configuration Guide. BFD is supported only for single-hop IBGP and EBGP sessions with either IPv4 or IPv6 neighbors in the core or within a VRF. BFD is not supported for multi-hop BGP sessions (IBGP multi-hop or EBGP multi-hop). BFD behavior is identical for IBGP and EBGP single-hop sessions, and for IPv4 and IPv6 neighbors.

When you configure BFD for a BGP session, the normal BGP keepalive mechanism is not disabled. Unless you configure BGP not to do so, BGP still sends keepalive messages and brings the BGP session down if the holdtimer expires.

When you configure this feature, BGP requests BFD to start a BFD protocol session as soon as the BGP session enters the established state. BGP allows the BFD protocol session to come up only when the source address of received BFD packets matches the destination address of the BGP neighbor. When the BFD protocol session comes up, BGP logs this event and reports the session in subsequent show commands. If the BFD protocol session goes down, BGP immediately brings down the BGP session and takes all associated actions.

Whenever a BGP session leaves the established state, BGP requests BFD to stop the BFD protocol session. BGP also requests BFD to bring the BFD protocol session down and inform BGP if the local interface goes down.

To enable a BGP session to come up even if the remote peer does not support BFD or has not been configured to use BFD, the following behavior applies:

• The BGP session can come up when the BFD protocol session is not yet up.
• The BGP session can stay up even when the BFD protocol session never comes up.

You can specify a desired rate for receiving BFD packets from the peer, transmitting them to the peer, or both, by setting a desired time interval between the packets. The actual timer values can be different as a result of other applications requesting BFD protocol sessions on the same interface with different timer values, as a result of timer value negotiation between the local and remote BFD speakers, or both.

In the following example, the router is configured to send BFD packets to peer 10.25.43.1 with a minimum interval of 450 milliseconds between the packets, and to accept BFD packets from the peer only with the same minimum interval:

neighbor bfd-liveness-detection

• Use to enable BGP to detect whether a neighbor is unreachable by means of a BFD protocol session to the neighbor.
• The peers in a BGP adjacency use the configured values to negotiate the actual transmit intervals for BFD packets.
  • You can use the minimum-transmit-interval keyword to specify the interval at which the local peer proposes to transmit BFD control packets to the remote peer. The default value is 300 milliseconds.
  • You can use the minimum-receive-interval keyword to specify the minimum interval at which the local peer must receive BFD control packets from the remote peer. The default value is 300 milliseconds.
  • You can use the minimum-interval keyword to specify the same value for both of those intervals. Configuring a minimum interval has the same effect as configuring the minimum receive interval and the minimum transmit interval to the same value. The default value is 300 milliseconds.
• You can use the multiplier keyword to specify the detection multiplier value. The calculated BFD liveness detection interval can be different on each peer. The multiplier value is roughly equivalent to the number of packets that can be missed before the BFD session is declared to be down. The default value is 3.
• For details on liveness detection negotiation, see JUNOSe IP Services Configuration Guide.
• You can change the BFD liveness detection parameters at any time without stopping or restarting the existing session; BFD automatically adjusts to the new parameter value. However, no changes to BFD parameters take place until the values resynchronize with each peer.
• If you specify a BGP peer group by using the peerGroupName argument, all the members of the peer group inherit the characteristic configured with this command unless it is overridden for a specific peer.
• This command takes effect immediately.
• The BGP session does not flap when you enable BFD for a session that is already up or change the BFD timer values for an established session.
• If you remove the BFD configuration while the BGP sessions and the BFD protocol session are up, then the BGP session may flap because the remote BGP speaker cannot detect why the BFD session went down.
• Use the no version to disable BFD liveness detection for the neighbor. Use the default version to remove the explicit configuration from the peer or peer group and reestablish inheritance of the feature configuration.
• See neighbor bfd-liveness-detection.

Copyright © 2008, Juniper Networks, Inc. All rights reserved. Trademark Notice.