- Description—Text description or alias if configured for the interface
- ifAdminStatus—One of the following administrative
states of the interface:
- ifAdminUp—Interface is administratively enabled
- ifAdminDown—Interface is administratively disabled
- ifAdminTesting—Interface is administratively configured in a testing state
- snmp trap link-status—Status of SNMP trapping (enabled or disabled)
- alarms detected—One of the following T3 alarms:
- No alarm present—No alarms present on the line
- Rcv RAI Failure—Remote device is sending a far end alarm failure
- Xmt RAI Failure—Local device is sending a far end alarm failure
- Rcv AIS—Remote device is sending an alarm indication signal (AIS)
- Xmt AIS—Local device is sending an AIS
- Rcv LOF—Loss of one or more frames from the remote end
- Rcv LOS—Loss of signal at the local end
- Undefined line status—Indicates that the line is
in an undefined state
Note: The alarms detected field does not appear for interfaces that you disabled in the software.
- framing—Type of framing format
- line code—Type of line code format
- clock source—Type of clock source
- cable length—Cable length, in feet
- Loopback—State of loopback for the controller: enabled
or disabled. If loopback is enabled, one of the following states is
displayed:
- Diagnostic—Loops the data back toward the router and sends an AIS toward the network
- Payload—Loops the data toward the network after the framer has processed the data
- Line—Loops the data toward the network before the data reaches the framer
- MDL Transmit Path—Status of path transmission: active or not active
- MDL Transmit Test-Signal—Status of test signal: active or not active
- MDL Transmit Idle-Signal—Status of idle signal: active or not active
- Equipment Identification Code—eic string for MDL
- Line Identification Code—lic string for MDL
- Frame Identification Code—fic string for MDL
- Unit Identification Code—unit string for MDL
- Facility Identification Code—pfi string for MDL
- Port Code—port string for MDL
- Generator Number—generator string for MDL
- BERT test—Number of current test and total number
of tests
- Test interval—Length of the BERT test
- status—Sync (controller is synchronized with remote device) or NoSync (controller is not synchronized with remote device)
- Sync count—Number of times the pattern detector synchronized with the incoming data pattern
- Received bit count—Number of bits received
- Error bit count—Number of bits with errors
- Number of valid intervals—Number of 15-minute intervals since the line module was last powered on or reset
- Time elapse in current interval—Reported in 15-second intervals
- P-bit errored seconds—Number of errored seconds encountered by a T3 in the current interval
- P-bit severely errored seconds—Number of severely errored seconds encountered by a T3 in the current interval
- Severely errored frame seconds—Number of severely errored framing seconds encountered by a T3 in the current interval
- Unavailable seconds—Number of unavailable seconds encountered by a T3 in the current interval
- Line code violations—Number of line code violations encountered by a T3 in the current interval
- P-bit coding violations—Number of coding violations encountered by a T3 in the current interval
- Line errored seconds—Number of line errored seconds encountered by a T3 in the current interval
- C-bit coding violations—Number of C-bit coding violations encountered by a T3 in the current interval
- C-bit errored seconds—Number of C-bit errored seconds encountered by a T3 in the current interval
- C-bit severely errored seconds—Number of C-bit severely errored seconds encountered by a T3 in the current interval
host1#show controllers t3 2/0 DS3 2/0 Description: toronto ct3 interface ifAdminStatus = ifAdminDown snmp trap link-status = enabled No alarms detected Framing is C-BIT, Line Code is B3ZS, Clock Source is Line Cable Length is 0 ft Loopback Disabled MDL Transmit Path is not active MDL Transmit Test-Signal is active MDL Transmit Idle-Signal is not active Equipment Identification Code is ERX-1400 Line Identification Code is Bldg 10 Frame Identification Code is null string Unit Identification Code is 080001 Facility Identification Code is Site 25 Port Code is Port 0800 Generator Number is null string Number of valid interval - 96 Time elapse in current interval - 861 Ds3 Current Interval Counters P-bit errored seconds = 0 P-bit severely errored seconds = 0 Severely errored frame seconds = 0 Unavailable seconds = 0 Line code violations = 0 P-bit coding violations = 0 Line errored seconds = 0 C-bit coding violations = 0 C-bit errored seconds = 0 C-bit severely errored seconds = 0 Ds3 Last Interval Counters P-bit errored seconds = 0 P-bit severely errored seconds = 0 Severely errored frame seconds = 0 Unavailable seconds = 0 Line code violations = 0 P-bit coding violations = 0 Line errored seconds = 0 C-bit coding violations = 0 C-bit errored seconds = 0 C-bit severely errored seconds = 0 Ds3 24 Hour Total Counters P-bit errored seconds = 0 P-bit severely errored seconds = 0 Severely errored frame seconds = 0 Unavailable seconds = 0 Line code violations = 0 P-bit coding violations = 0 Line errored seconds = 0 C-bit coding violations = 0 C-bit errored seconds = 0 C-bit severely errored seconds = 0
host1#show controllers t3 brief
Interfaces ifAdminStatus OperationalStatus 5/0(channelized) up up 5/1(channelized) up up 5/2(channelized) up down 5/3(channelized) down down 5/4(channelized) down down 5/5(channelized) down down 5/6(channelized) down down 5/7(channelized) down down 5/8(channelized) down down 5/9(channelized) down down 5/10(channelized) down down 5/11(channelized) down down 3/0(channelized) down down 3/1(channelized) down down 3/2(channelized) down down 4/0:1/1(unchannelized) up down 4/2:1/1(channelized) up lowerLayerDown
- Description—Text description or alias if configured for the interface
- ifOperStatus—Physical state of the interface:
- ifOperDown—Interface is not functioning
- ifOperLowerLayerDown—Lower layer in the interface stack is not functioning
- ifOperNotPresent—Module has been removed from the chassis
- ifOperTesting—Interface is being tested
- ifOperUp—Interface is functioning
- Yellow Alarm detection—Status of yellow alarm detection: active or not active
- Yellow Alarm generation—Status of yellow alarm generation: active or not active
- snmp trap link-status—Status of SNMP trapping (enabled or disabled)
- Framing—Type of framing format
- Clock source—Type of clock source
- Loopback state—Type of loopback (if enabled) and status: enabled or disabled
- Last remote loopback request sent—None or deactivate
- FDL—Status of FDL: standard configured or not configured
- FDL Transmit Path—Status of path transmission: active or not active
- FDL Transmit Idle-Signal—Status of idle signal: active or not active
- FDL Transmit Test-Signal—Status of test signal: active or not active
- Equipment Identification Code—eic string for FDL
- Line Identification Code—lic string for FDL
- Frame Identification Code—fic string for FDL
- Unit Identification Code—unit string for FDL
- Facility Identification Code—pfi string for FDL
- Port Code—port string for FDL
- Generator Number—generator string for FDL
- BERT test—Number of current test and total number
of tests
- Test interval—Length of the BERT test
- status—Sync (controller is synchronized with remote device) or NoSync (controller is not synchronized with remote device)
- Sync count—Number of times the pattern detector synchronized with the incoming data pattern
- Received bit count—Number of bits received
- Error bit count—Number of bits with errors
- Number of valid intervals—Number of 15-minute intervals since the line module was last powered on or reset
- Time elapse in current interval—Statistics are reported in 15-minute intervals
- Errored seconds—Number of errored seconds encountered by a T1 in the current interval
- Severely errored seconds—Number of severely errored seconds encountered by a T1 in the current interval
- Severely errored frame seconds—Number of severely errored framing seconds encountered by a T1 in the current interval
- Unavailable seconds—Number of unavailable seconds encountered by a T1 in the current interval
- Clock slip seconds—Number of clock slips encountered by a T1 in the current interval
- Path code violations—Number of coding violations encountered by a T1 in the current interval
- Line errored seconds—Number of line errored seconds encountered by a T1 in the current interval
- Bursty errored seconds—Number of bursty errored seconds encountered by a T1 in the current interval
- Degraded minutes—Number of minutes that a T1 line is degraded
- Line code violations—Number of line code violations encountered by a T1 in the current interval
host1#show controllers t1 2/0:1 brief DS3 2/0:1 ifOperStatus = ifOperUp Yellow Alarm detection is active Yellow Alarm generation is active snmp trap link-status = disabled Framing is D4, Line Code is Ami, Clock Source is Internal - Module
Allocated Ds0 time slot map = 0x0 Loopback Enabled - Diagnostic Last Remote Loopback Request Sent - Deactivate FDL is not configured FDL Transmit Path-Id is not active FDL Transmit Test-Signal is not active FDL Transmit Idle-Signal is not active Equipment Identification Code is the null string Line Identification Code is the null string Frame Identification Code is the null string Unit Identification Code is the null string Facility Identification Code is the null string Port Code is the null string Generator Number is the null string BERT test - 2 in 23 Test Interval 1 minute(s), Complete Sync count = 1 Received bit count = 92148912 Error bit count = 17 Number of valid interval - 90 Time elapse in current interval - 580
host1#show controllers t1 brief
Interfaces ifAdminStatus OperationalStatus 5/0:1(framed) up lowerLayerDown 5/0:2(framed) up lowerLayerDown 5/0:3(framed) up lowerLayerDown 5/0:4(framed) up lowerLayerDown 5/0:5(framed) up lowerLayerDown 5/0:6(framed) up lowerLayerDown ... 5/2:26(framed) up lowerLayerDown 5/2:27(framed) up lowerLayerDown 5/2:28(framed) up lowerLayerDown
host1#show controllers t1 1/0:1
DS1 1/0:1 Description: toronto t1 channel ifOperStatus = ifOperUp Yellow Alarm detection is active Yellow Alarm generation is active snmp trap link-status = disabled Framing is D4, Line Code is Ami, Clock Source is Internal - Module
Allocated Ds0 time slot map = 0x0 Last Remote Loopback Request Sent - Deactivate FDL is not configured FDL Transmit Path-Id is not active FDL Transmit Test-Signal is not active FDL Transmit Idle-Signal is not active Equipment Identification Code is the null string Line Identification Code is the null string Frame Identification Code is the null string Unit Identification Code is the null string Facility Identification Code is the null string Port Code is the null string Generator Number is the null string BERT test - 2 in 23 Test Interval 1 minute(s), Complete Sync count = 1 Received bit count = 92148912 Error bit count = 17 Number of valid interval - 90 Time elapse in current interval - 580
Ds1 Current Interval Counters Errored seconds = 0 Severely errored second = 0 Severely errored frame seconds = 0 Unavailable seconds = 0 Clock slip seconds = 0 Path code violations = 0 Line errored seconds = 0 Bursty errored seconds = 0 Degraded minutes = 0 Line code violations = 0
Ds1 Last Interval Counters Errored seconds = 0 Severely errored second = 0 Severely errored frame seconds = 0 Unavailable seconds = 0 Clock slip seconds = 0 Path code violations = 0 Line errored seconds = 0 Bursty errored seconds = 0 Degraded minutes = 0 Line code violations = 0
Ds1 24 Hour Total Counters Errored seconds = 25 Severely errored second = 7 Severely errored frame seconds = 25 Unavailable seconds = 0 Clock slip seconds = 6 Path code violations = 18 Line errored seconds = 0 Bursty errored seconds = 0 Degraded minutes = 0 Line code violations = 0
