[Contents] [Prev] [Next] [Index] [Report an Error]

Monitoring Interface Statistics

You can set statistics baselines for the section, line, and path layers using the baseline interface sonet commands.

To display statistics for SONET and SDH interfaces, use the show controllers sonet commands. Use the delta options to display statistics with the baseline subtracted.

baseline line interface sonet

Use to set a statistics baseline for the SONET/SDH line layer.
The router implements the baseline by reading and storing the MIB statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved.
Use the total [ delta ] keywords with the show controllers sonet line command to view the baseline statistics.
Example 1—Sets a baseline for SONET line layer interfaces on ERX-14xx models, ERX-7xx models, or the ERX-310 routerhost1#baseline line interface sonet 2/0
Example 2—Sets a baseline for SONET line layer interfaces on the E320 routerhost1#baseline line interface sonet 3/0/0
There is no no version.
See baseline line interface sonet.

baseline path interface sonet

Use to set a statistics baseline for the SONET/SDH path layer.
The router implements the baseline by reading and storing the MIB statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved.
Use the total [ delta ] keywords with the show controllers sonet path command to view the baseline statistics.
Example 1—Sets a baseline for SONET path layer interfaces on ERX-14xx models, ERX-7xx models, or the ERX-310 routerhost1#baseline path interface sonet 2/0
Example 2—Sets a baseline for SONET path layer interfaces on the E320 routerhost1#baseline path interface sonet 3/0/0
There is no no version.
See baseline path interface sonet.

baseline section interface sonet

Use to set a statistics baseline for the SONET/SDH section layer.
The router implements the baseline by reading and storing the MIB statistics at the time the baseline is set and then subtracting this baseline whenever baseline-relative statistics are retrieved.
Use the total [ delta ] keywords with the show controllers sonet section commands to view the baseline statistics.
Example 1—Sets a baseline for SONET section layer interfaces on ERX-14xx models, ERX-7xx models, or the ERX-310 routerhost1#baseline section interface sonet 2/0
Example 2—Sets a baseline for SONET section layer interfaces on the E320 routerhost1#baseline section interface sonet 3/0/0
There is no no version.
See baseline section interface sonet.

show controllers sonet

Use to display the configuration for SONET and SDH interfaces.
Field descriptions
- Interface specifier in slot/port format (ERX-14xx models, ERX-7xx models, and the ERX-310 router) or slot/adapter/port format (E120 and E320 routers)
- non channelized—Unchannelized path
- channelized—Number of channels and speed for the interface
- ifAdminStatus—Configured status of the interface: up or down
- description—Configured description of the controller
- snmp trap link-status—State of SNMP link-status processing for the section and line layers of the interface: enabled or disabled
- alarms used for operational status calculation—Types of defects that the router uses to determine the operational status of the interface at the section and line layers
- defect trigger soaking delay—Time that the router waits to set an alarm when the router records a defect at the section or line layer
- Operational Status—Physical state of the interface:
  - up—Interface is operational
  - down, failure alarm—Interface is not operational; type of defect that caused failure is specified
  - time since last status change—Time since the module was rebooted
- Loopback State—Type of loopback configured on the interface
- Mode—Type of interface: SONET or SDH
- Timing source—Type of clock source configured for the channel:
  - line—Internal clock is from the line module itself
  - chassis—Internal clock is from the configured router clock
- Receive FIFO Overruns—Number of times received FIFO was overrun
- Current section defects—Number of suspect bit patterns found in several consecutive frames in section layer
- Current line defects—Number of suspect bit patterns found in several consecutive frames in line layer
- Received SONET overhead—Section and line overhead bytes present in the receive side of the interface at any particular time
- Transmitted SONET overhead—Section and line overhead bytes present in the transmit side of the interface at any particular time
- Channel configuration—Parameters for specific controllers. The actual parameters depend on the controller.
  - ifAdminStatus—State of the controller in the software configuration: up or down
  - snmp trap link-status—State of SNMP link status processing for the path layer: enabled or disabled
  - alarms used for operational status calculation—Types of defects that the router uses to determine the operational status of the interface at the path layer
  - defect trigger soaking delay—Time that the router waits to set an alarm when the router records a defect at the path layer
  - c2 byte—Setting of path signal byte: set by upper interface type (automatic setting) or configured value
  - Operational Status—Physical state of the controller: up, down, or lowerLayerDown
  - time since last status change: time the controller has been in the current physical state
- Received SONET Path overhead—Path overhead bytes present in the receive side of the interface at any particular time
- Transmitted SONET Path overhead—Path overhead bytes present in the transmit side of the interface at any particular time

Example

host1# show controllers sonet 1/0
show controllers sonet 1/0oc3 1/0
non channelized
ifAdminStatus: up
description: link1
snmp trap link-status: enabled
alarms used for operational status calculation: LOS LOF AIS RDI
defect trigger soaking delay: 2500 milliseconds
Operational Status: down, failure alarm: AIS
      time since last status change: 07:33:12
Loopback State: none
Mode: sonet
Timing source: line
Receive FIFO Overruns: 0, Framer stats: 0/0
Current section defects: none
Current line    defects: AIS
Received SONET overhead:
F1      :  n/a, J0      :  n/a, K1      : 0xFF, K2      : 0xFF, S1      : 0xFF
Transmitted SONET overhead:
F1      : 0x00, J0      : 0x01, K1      : 0x00, K2      : 0x00, S1      : 0x00
Channel configuration:
channel = 0, path = oc3, hierarchy = 1/0, current path defects: LowerLayerDefect
 ifAdminStatus: up
 snmp trap link-status: disabled
 alarms used for operational status calculation: LOP AIS
 defect trigger soaking delay: 2500 milliseconds
 c2 byte set by upper interface type
 Operational Status: lowerLayerDown
       time since last status change: 07:33:12
Received SONET Path overhead:
F2      :  n/a, Z3      :  n/a, Z4      :  n/a, C2      : 0xFF, C2Exp   : 0x00
Transmitted SONET Path overhead:
F2      : 0x00, Z3      : 0x00, Z4      : 0x00, C2      : 0x00

See show controllers sonet.

show controllers sonet line | path | section

Use to display statistics for the different layers in channelized SONET and SDH interfaces. Figure 5 and Figure 6 show the layers in the interfaces.
For definitions of the MIB statistics, see RFC 2558—Definitions of Managed Objects for the SONET/SDH Interface Type (March 1999).
Specify an interface in slot/port format (ERX-14xx models, ERX-7xx models, and the ERX-310 router) or slot/adapter/port format (E120 and E320 routers).
To view statistics for a layer, specify the type of layer.
To view all statistics for all sessions, specify the total keyword.
To view baselined statistics for all intervals, specify the delta total keywords.
Field descriptions
- Current Interval Counters—Statistics for the current 15-minute interval
  The following fields may appear in line, path, or section:
  - ES—Number of errored seconds encountered by a T1 or an E1 in an interval
  - SES—Number of severely errored seconds encountered in an interval
  - UAS—Number of unavailable seconds encountered in an interval
  - SEFS—Number of severely errored framing seconds encountered in an interval
  - (Code Violations)—Number of coding violations encountered in an interval (BIP-B1, BIP-B2, BIP-B3)
  - RDI—Number of remote defect indications
  - AIS—Number of alarm indication signals
  - BERR-SF—Number of bit error rate signal failures
  - BERR-SD—Number of bit error rate signal degrades
  - LOS—Number of loss of signal alarms
  - LOF—Number of loss of frame alarms
  - LOP—Number of loss of pointers
  - UNEQ—Number of unequipped alarms
  - PLM—Number of payload mismatchs
- Last Interval Counters—Statistics for the previous 15-minute interval
- Current Far End Interval Counters—Statistics for the remote connection associated with the SONET/SDH path in the current 15-minute interval
  - REI—Number of remote error indications
- Far End Last Interval Counters—Statistics for the remote connection associated with the SONET/SDH path in the previous 15-minute interval
- Total Interval Counters—Statistics for all intervals or baselined statistics
- Total Far End Counters—Statistics for all remote connections associated with the SONET/SDH path

Example 1—Shows the MIB statistics for the path layer on interface 1/0.

host1#show controllers sonet 1/0 path

Channel number 0

Number of valid intervals - 31
Time elapsed in current interval - 141
Current status                   = LowerLayerDefect

Current Path Interval Counters           Seconds      Counts        State
ES                                            0
SES                                           0
UAS                                         141
RDI                                         141             0       Active
AIS                                         141             0       Active
LOP                                           0             0       OK
UNEQ                                          0             0       OK
PLM                                         141             0       Active
BIP-B3  (Code Violation)                      0             0

Last Path Interval Counters              Seconds      Counts
ES                                            0
SES                                           0
UAS                                         900
RDI                                         900             0
AIS                                         900             0
LOP                                           0             0
UNEQ                                          0             0
PLM                                         900             0
BIP-B3  (Code Violation)                      0             0

Total Path Counters                      Seconds      Counts
ES                                            0
SES                                           0
UAS                                       27255
RDI                                       27255             0
AIS                                       27255             0
LOP                                           0             0
UNEQ                                          0             0
PLM                                       27255             0
BIP-B3  (Code Violation)                      0             0

Current Far End Path Interval Counters   Seconds      Counts
ES                                            0
SES                                           0
UAS                                         141
REI                                           0             0

Far End Last Path Interval Counters      Seconds      Counts
ES                                            0
SES                                           0
UAS                                         900
REI                                           0             0

Total Far End Path Counters              Seconds      Counts
ES                                            0
SES                                           0
UAS                                       27255
REI                                           0             0

Example 2—Shows the MIB statistics for the line layer on interface 1/0.

host1#show controllers sonet 1/0 line

Number of valid intervals - 31
Time elapsed in current interval - 114
Current status                   = AIS

Current Line Interval Counters           Seconds      Counts        State
ES                                            0
SES                                           0
UAS                                         113
RDI                                           0             0       OK
AIS                                         113             0       Active
BERR-SF                                       0             0       OK
BERR-SD                                       0             0       OK
BIP-B2 (Code Violation)                       0             0

Last Line Interval Counters              Seconds      Counts
ES                                            0
SES                                           0
UAS                                         900
RDI                                           0             0
AIS                                         900             0
BERR-SF                                       0             0
BERR-SD                                       0             0
BIP-B2 (Code Violation)                       0             0

Total Line Counters                      Seconds      Counts
ES                                            0
SES                                           0
UAS                                       27227
RDI                                           0             0
AIS                                       27227             1
BERR-SF                                       0             0
BERR-SD                                       0             0
BIP-B2 (Code Violation)                       0             0

Current Far End Line Interval Counters   Seconds      Counts
ES                                            0
SES                                           0
UAS                                           0
REI                                           0             0

Far End Last Line Interval Counters      Seconds      Counts
ES                                            0
SES                                           0
UAS                                           0
REI                                           0             0

Total Far End Line Counters              Seconds      Counts
ES                                            0
SES                                           0
UAS                                          10
REI                                           0             0

Example 3—Shows the MIB statistics for the section layer on interface 1/0.

host1#show controllers sonet 1/0 section

Number of valid intervals - 31
Time elapsed in current interval - 49
Current status                   = No Defect

Current Section Interval Counters        Seconds      Counts        State
ES                                            0
SES                                           0
SEFS                                          0
LOS                                           0             0       OK
LOF                                           0             0       OK
BIP-B1 (Code Violation)                       0             0

Last Section Interval Counters           Seconds      Counts
ES                                            0
SES                                           0
SEFS                                          0
LOS                                           0             0
LOF                                           0             0
BIP-B1 (Code Violation)                       0             0

Total Section Counters                   Seconds      Counts
ES                                            1
SES                                           1
SEFS                                          0
LOS                                           0             0
LOF                                           0             0
BIP-B1 (Code Violation)                       1            16

Example 4—Shows all statistics for all sessions for the section layer on interface 2/0.

host1#show controllers sonet 2/0 section total

Number of valid intervals - 31
Time elapsed in current interval - 244

Total Section Counters                   Seconds      Counts
ES                                            1
SES                                           1
SEFS                                          0
LOS                                           0             0
LOF                                           0             0
BIP-B1 (Code Violation)                       1            16

See show controllers sonet.

[Contents] [Prev] [Next] [Index] [Report an Error]