A
C
- cabling
- fast Ethernet 1, 2
- overview
- power 1, 2
- recommendations
- required tools
- Case Manager, Juniper
- cleaning platform
- compliance, regulatory
- console See management console
- CTP overview
- CTP1002 platform 1
- CTP1004 platform 1
- CTP1012 platform 1
- CTPOS
- CTPView
- customer support 1
- contacting Juniper
- information needed
- locating serial numbers
- return procedure 1, 2
D
- damaged components, returning
- DB-25 connector 1, 2
- DB-9
- declaration of conformity, EC
E
H
I
- inspecting before installation
- installing
- interface modules
- pinouts See pinouts
J
M
- maintaining
- management console
- modules and components
P
- pinouts
- power
- powering off
- powering on 1, 2
- preinstallation responsibilities
R
S
T
- technical support
- troubleshooting power failures 1, 2
U
V
Download This Guide
Related Documentation
CTP1000 Interface Module 100-to-25-Pin Cable Pinouts
The CTP1004 and CTP1012 devices provide 100-pin connectors for external serial interface connections. The CTP1004 has one connector, and the CTP1012 has three 100-pin connectors. This 100-pin output is on a quad cable (a Revision B or later cable ordered separately) with the other end split into four standard DB-25 connectors, labeled P0, P1, P2, and P3, connected to the serial interface. These port numbers correspond to the port-numbering scheme implemented in the software configuration.
The pinouts for these connections have different configurations for EIA-530, RS-232, voice, and T1 interface signals.
- EIA-530 Connector Interface Signal Pinouts
- RS-232 Connector Interface Signal Pinouts
- Voice Interface Signal Pinouts
- T1 Interface Signal Pinouts
EIA-530 Connector Interface Signal Pinouts
Table 4 lists the EIA-530 interface signal pinouts for the 25-pin connector.
Table 4: EIA-530 Connector Interface Signals
DB-25 Pin | To/From CTP | Description | Circuit |
---|---|---|---|
1 | — | Shield | — |
2 | To | Transmitted data—A | BA |
3 | From | Received data—A | BB |
4 | To | Request to send—A | CA |
5 | From | Clear to send—A | CB |
6 | From | Data set ready—A | CC |
7 | — | Signal ground | Ground |
8 | From | Data carrier detect—A | CF |
9 | From | Receive signal element timing—B | DD |
10 | From | Data carrier detect—B | CF |
11 | To | Transmit signal element timing—B (DTE) | DA |
12 | From | Transmit signal element timing—B (DCE) | DB |
13 | From | Clear to send—B | CB |
14 | To | Clear to send—B | BA |
15 | From | Transmit signal element timing—A (DCE) | DB |
16 | From | Received data—B | BB |
17 | From | Receive signal element timing—A | DD |
18 | To | Local loopback | LL |
19 | To | Request to send—B | CA |
20 | To | Data terminal ready—A | CD |
21 | To | Remote loopback | RL |
22 | From | Data set ready—B | CC |
23 | To | Data terminal ready—B | CD |
24 | To | Transmit signal element timing—A (DTE) | DA |
25 | — | Test mode | TM |
RS-232 Connector Interface Signal Pinouts
Table 5 lists the RS-232 interface signal pinouts for the 25-pin connector.
Table 5: RS-232 Connector Interface Signals
DB-25 Pin | To/From CTP | Description | Circuit |
---|---|---|---|
1 | — | Shield | — |
2 | To | Transmitted data—A | BA |
3 | From | Received data—A | BB |
4 | To | Request to send—A | CA |
5 | From | Clear to send—A | CB |
6 | From | Data set ready—A | CC |
7 | — | Signal ground | Ground |
8 | From | Data carrier detect—A | CF |
15 | From | Transmit signal element timing—A (DCE) | DB |
17 | From | Receive signal element timing—A | DD |
20 | To | Data terminal ready—A | CD |
22 | From | Data set ready—B | CC |
24 | To | Transmit signal element timing—A (DTE) | DA |
Voice Interface Signal Pinouts
Table 6 lists the voice interface signal pinouts for the 25-pin connector.
Table 6: Voice Interface Signals
DB-25 Pin | To/From CTP | Description | Circuit |
---|---|---|---|
1 | — | Shield | — |
2 | To | Channel 0 voice RX—A | Channel 0 |
3 | From | Channel 0 voice TX—A | Channel 0 |
4 | To | Channel 1 voice signaling input A | Channel 1 |
5 | From | Channel 1 voice signaling output A | Channel 1 |
6 | From | Channel 0 voice signaling output A | Channel 0 |
9 | From | Channel 1 voice TX—A | Channel 1 |
11 | To | Channel 1 voice RX—B | Channel 1 |
13 | From | Channel 1 voice signaling output—B | Channel 1 |
14 | To | Channel 0 voice RX—B | Channel 0 |
16 | From | Channel 0 voice TX—B | Channel 0 |
17 | From | Channel 1 voice TX—B | Channel 1 |
19 | To | Channel 1 voice signaling input—B | Channel 1 |
20 | To | Channel 0 voice signaling input—A | Channel 0 |
22 | From | Channel 0 voice signaling output—B | Channel 0 |
23 | To | Channel 0 voice signaling input—B | Channel 0 |
24 | To | Channel 1 voice RX—A | Channel 1 |
T1 Interface Signal Pinouts
Table 7 lists the T1 interface signal pinouts for the 25-pin connector.
Table 7: T1 Interface Signals
DB-25 Pin | To/From CTP | Description |
---|---|---|
1 | — | Shield |
2 | To | Transmitted data—A |
3 | From | Received data—A |
7 | — | Signal ground |
14 | To | Transmitted data—B |
16 | From | Received data—B |