Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation  Back up to About Overview 
ContentIndex
  
[+] Expand All
[-] Collapse All

 A  C  D  E  H  I  J  M  P  R  S  T  U  V

 

A

accessing    
connecting directly
console ports
HyperTerminal
management console
SSH setup
 

C

cabling    
fast Ethernet    12
overview
power    12
recommendations
required tools
Case Manager, Juniper
cleaning platform
compliance, regulatory    
Canadian
FCC    12
FDA
console     See management console    
CTP overview
CTP1002 platform    1
specifications
CTP1004 platform    1
specifications
CTP1012 platform    1
specifications
CTPOS
CTPView
customer support    1
contacting Juniper
information needed
locating serial numbers
return procedure    12
 

D

damaged components, returning
DB-25 connector    12
DB-9    
connector
crossover cable
declaration of conformity, EC    
CTP1000
 

E

EIA-530 data interface
EIA530(A) data interface
environmental requirements
 

H

HyperTerminal access
 

I

inspecting before installation
installing    
before
freestanding
responsibilities
interface modules    
pinouts     See pinouts    
 

J

JTAC, contacting    12
 

M

maintaining    
cleaning
storing modules
tools required
management console    
accessing
direct connection
pinouts
port setup
modules and components    
cleaning
replacing
storing
 

P

pinouts    
100-pin connector
power    
cables, DC    12
failures
shutdowns
powering off
powering on    12
preinstallation responsibilities
 

R

rack    
installation guidelines
installing in
mechanical requirements
requirements
space requirements
reclamation and recycling
replacing components
return procedure    12
RJ-45 connector    123456
RS-232 port    123456
 

S

safety guidelines
serial number, locating
SSH connection
storing components
 

T

technical support
troubleshooting power failures    12
 

U

unpacking and inspecting
 

V

V.35 data interface

CTP1004 Platform

The CTP1004 platform is a 1-U high, full-rack wide chassis designed for tabletop or shelf installation. It can also be installed in a rack with the supplied rack-mounting kit. The CTP1004 device does not have any removable interface modules, but does use a removable Type II CompactFlash card and is available in both AC-powered and DC-powered versions. It has multiple cooling fans, and airflow is front to back. See Figure 3, Figure 4, and Figure 5.

Figure 3: CTP1004 Platform (AC and DC Version, Front View)

CTP1004 Platform (AC and
DC Version, Front View)

The front panel comprises the following components (see Figure 3):

  • Power LED—Green when power is connected and the power switch is set to the ON position.
  • HDD LED—Red when the flash card is in use.
  • Front power switch—Set to ON position when 1 is briefly pressed. Set to OFF when 1 is pressed for four or more seconds.
  • Removable flash card—The device must be powered off when you insert or remove the flash card.
  • USB ports.

The rear panel comprises the following components (see Figure 4 and Figure 5):

  • Power supply—Uses a standard IEC power cord for the AC version. Uses a 18-AWG fork terminal connector for the DC version. There is no power redundancy for the DC version.
  • Ethernet connection—Provides the 100-Mbps Ethernet connection to the IP network by means of a local Ethernet switch or router.
  • Console connection—Provides an asynchronous TTY connection for locally configuring the CTP device. See CTP1000 Console Cable Pinouts to find pinout information for this connector.
  • Interface connector—Features a 100-pin connector providing four serial interfaces when used with the CTP quad cable. SeeCTP1000 Interface Module 100-to-25-Pin Cable Pinouts to find pinout information for this connector.
  • USB ports.

Figure 4: CTP1004 Platform (AC Version, Rear View)

CTP1004 Platform (AC Version,
Rear View)

Figure 5: CTP1004 Platform (DC Version, Rear View)

CTP1004 Platform (DC Version,
Rear View)

Note: Do not remove the screws or the protective cover for the DC power terminal when cabling for power (see Figure 6). Use a magnetic screwdriver to loosen the two inner screws two to three turns.

Slide the fork terminal connectors up through the bottom of the protective cover. If you install the wires from the top, they will block the power switch.

Figure 6: Wiring a CTP1004 Platform (DC Version)

Wiring a CTP1004 Platform
(DC Version)

Related Documentation

Modified: 2015-11-22