Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation  Back up to About Overview 
ContentIndex
  
[+] Expand All
[-] Collapse All

 A  C  D  E  H  I  J  M  P  R  S  T  U  V

 

A

accessing    
connecting directly
console ports
HyperTerminal
management console
SSH setup
 

C

cabling    
fast Ethernet    12
overview
power    12
recommendations
required tools
Case Manager, Juniper
cleaning platform
compliance, regulatory    
Canadian
FCC    12
FDA
console     See management console    
CTP overview
CTP1002 platform    1
specifications
CTP1004 platform    1
specifications
CTP1012 platform    1
specifications
CTPOS
CTPView
customer support    1
contacting Juniper
information needed
locating serial numbers
return procedure    12
 

D

damaged components, returning
DB-25 connector    12
DB-9    
connector
crossover cable
declaration of conformity, EC    
CTP1000
 

E

EIA-530 data interface
EIA530(A) data interface
environmental requirements
 

H

HyperTerminal access
 

I

inspecting before installation
installing    
before
freestanding
responsibilities
interface modules    
pinouts     See pinouts    
 

J

JTAC, contacting    12
 

M

maintaining    
cleaning
storing modules
tools required
management console    
accessing
direct connection
pinouts
port setup
modules and components    
cleaning
replacing
storing
 

P

pinouts    
100-pin connector
power    
cables, DC    12
failures
shutdowns
powering off
powering on    12
preinstallation responsibilities
 

R

rack    
installation guidelines
installing in
mechanical requirements
requirements
space requirements
reclamation and recycling
replacing components
return procedure    12
RJ-45 connector    123456
RS-232 port    123456
 

S

safety guidelines
serial number, locating
SSH connection
storing components
 

T

technical support
troubleshooting power failures    12
 

U

unpacking and inspecting
 

V

V.35 data interface

CTP1002 Platform

The Juniper Networks CTP1002 Circuit to Packet platform is a 1-U high, half-rack wide chassis designed for tabletop or shelf installation. It can also be installed in a rack with the supplied rack-mounting kit. The CTP1002 platform does not have any removable interface modules or cooling fans, but does use a removable Type II CompactFlash card. It is available in an AC-powered version only. See Figure 1.

Figure 1: CTP1002 Chassis (Front View)

CTP1002 Chassis (Front View)

The front panel comprises the following components (see Figure 1):

  • Power LED—Green when power is connected and the power switch is set to the ON position.
  • HDD LED—Red when the drive is in use.
  • Front power switch—Set to ON position when 1 is briefly pressed. Set to OFF when 1 is pressed for four or more seconds.
  • Removable flash drive—The device must be powered off when you insert or remove the flash drive.

The rear panel comprises the following components (see Figure 2):

Figure 2: CTP1002 Chassis (Rear View)

CTP1002 Chassis (Rear View)
  • Power input from the external 12-VDC power supply.
  • Port 0 and port 1 DB-25 connectors—DB-25 connectors are used for terminating EIA530, RS-232, V.35, 4WTO, and T1 circuits.

    The DB-25 port connector pinout is the same as the quad cables used on the larger CTP platforms. SeeCTP1000 Interface Module 100-to-25-Pin Cable Pinouts to find pinout information for this connector.

  • COM 2 console connection—Provides an asynchronous TTY connection for local configuration of the CTP platform. See CTP1000 Console Cable Pinouts to find pinout information for this connector.
  • Fast Ethernet connector—Provides the 100-Mbps Ethernet connection to the IP network by means of a local Ethernet switch or router.
  • USB port.

Related Documentation

Modified: 2015-11-22