Data Collection via SNMP
Data collection via SNMP is a useful alternative for collecting network statistics in systems where Juniper Telemetry Interface (JTI) is not available or in multi-vendor systems. You can use these statistics for performance management.
You can collect the following statistics by using SNMP collection tasks that poll the SNMP management information base (MIB):
Interface statistics. See Table 1 for details.
LSP statistics. See Table 1 for details.
If the LSPs are part of a P2MP group, the P2MP group information is displayed in the P2MP Group tab in the network information table that is located at the bottom of the topology view.
You can collect CoS statistics only for Juniper and Cisco devices.
Table 1 describes the specific object identifiers (OIDs) that are collected for interface statistics and LSP statistics.
Table 1: OIDs for Interface and LSP Statistics
(Generic refers to all vendor devices supported in NorthStar)
Table 2 describes the specific OIDs that are collected for CoS statistics for Juniper devices.
Table 2: OIDs for CoS Statistics - Juniper Devices
Table 3 describes the specific OIDs that are collected for CoS statistics for Cisco devices.
Table 3: OIDs for CoS Statistics - Cisco Devices
CISCO-CLASS-BASED-QOS-MIB:: cbQosClassMapStats. cbQosCMDropByte64
NorthStar supports Cisco Model Driven Telemetry (MDT), a potentially faster and less costly alternative for retrieving interface and LSP traffic metrics from Cisco devices. See Support for Cisco Model Driven Telemetry for more information.
NorthStar does not support collection of SR-TE LSP statistics via SNMP.
The collection process via SNMP involves the following tasks:
Installation of Collectors
The collectors are installed in the same machine as the NorthStar Controller application server (single-server deployment) by the install.sh script when you install the controller itself. Once installed, you can see the collector group of processes:
[root@pcs-q-pod05 ~]# supervisorctl status
analytics:elasticsearch RUNNING pid 3374, uptime 6:33:42 analytics:esauthproxy RUNNING pid 3373, uptime 6:33:42 analytics:logstash RUNNING pid 5600, uptime 6:31:15 collector:es_publisher RUNNING pid 12899, uptime 0:37:03 collector:task_scheduler RUNNING pid 12900, uptime 0:37:03 collector:worker1 RUNNING pid 3385, uptime 6:33:42 collector:worker2 RUNNING pid 3387, uptime 6:33:42 collector:worker3 RUNNING pid 3386, uptime 6:33:42 collector:worker4 RUNNING pid 3388, uptime 6:33:42
Configure Devices in Device Profile and Test Connectivity
Before you can run SNMP collection, you must configure login credentials and SNMP parameters for the devices. In the web UI, from the More Options menu, navigate to Administration > Device Profile. Select a device and click Modify. Click the Access Parameters tab to enter login credentials and the SNMP Parameters tab to enter SNMP parameters.
See Device Profile and Connectivity Testing for detailed instructions on setting up devices with SNMP parameters, and also on testing SNMP connectivity to those devices.
Run Device Collection
You must run device collection before attempting to run SNMP traffic collection. This is necessary to establish the baseline network information including the interfaces and LSPs. Once device collection has been run, SNMP traffic collection tasks have the information they need to poll the interfaces and the LSPs.
Schedule and Run SNMP Data Collection Tasks
Completion of device profiles (Administration > Device Profile) and running device collection are prerequisites for successfully running SNMP collection.
To schedule a new SNMP collection task, navigate to Administration > Task Scheduler from the More Options menu.
- Click Add in the upper right corner. The Create New Task window is displayed as shown in Figure 1.
- Enter a name for the task and use the drop-down menu to
select the task type as SNMP Traffic Collection. Click Next.
The next window displayed offers you the opportunity to collect SNMP traffic for all devices, select devices, or groups. Figure 2 shows this window.
You would deselect devices for which you are using Cisco MDT.
- Click Next to proceed to the
scheduling parameters. The Create New Task - Schedule window is displayed
as shown in Figure 3. At least two
collections are necessary for the calculation of statistics. We recommend
setting up automatic recurrence of the task every 10 to 20 minutes.
Instead of scheduling recurrence, you can select to chain the task after an already-scheduled recurring task, so it launches as soon as the other task completes. When you select the “Chain after another task” radio button, a drop-down list of recurring tasks is displayed from which to select.
- Click Submit to complete the
addition of the new collection task and add it to the Task List. Click
a completed task in the list to display the results in the lower portion
of the window. There are three tabs in the results window: Summary,
Status, and History. An example of the Summary tab is shown in Figure 4. An example of the Status tab
is shown in Figure 5.
You can have only one SNMP traffic collection task per NorthStar server. If you attempt to add a second, the system will prompt you to approve overwriting the first one.
By default, NorthStar only collects statistics from the following interfaces when running SNMP traffic collection:
Physical, logical loopback, or logical management interfaces that can be associated with nodes in NorthStar
Logical interfaces associated with links in NorthStar
Logical interfaces belonging to a VRF
The interface types that can be discovered on devices and that should be used by traffic collection can be modified by editing the /opt/northstar/data/northstar.cfg file. Use a text editing tool such as vi, and use a comma as a separator. For example:
configServer_include_interfaceType=physical, loopbackMgmt, vrfInterface, linksInterface
The supported interface types are:
physical: Physical interfaces, expressed as the interface name without a dot (.) in it.
loopbackMgmt: Loopback and management interfaces expressed as the interface name starting with lo, fxp, me, or em.
vrfIf: Interfaces with which a VRF is associated.
linksIf: Interfaces on links.
all: All interfaces
These supported interface types are also commented in the northstar.cfg file.
Access the Data from the NorthStar Planner
You can access the collected data from the NorthStar Planner for planning and simulation purposes. In the NorthStar Planner, navigate to Traffic > Traffic aggregation. You can aggregate the traffic by hour and create a 24-hour traffic load file for each hour, aggregating the data for that particular hour across multiple days. The resulting file can be used as input into the traffic matrix solver.