Navigation
Table of Contents
Guide That Contains This Content
[+] Expand All
[-] Collapse All
Example: Routing Matrix with a TX Matrix Router Configuration
Routing Matrix with a TX Matrix Router Topology
Figure 1 shows Routing Matrix A, a basic routing matrix consisting of a TX Matrix router and two T640 routers. The TX Matrix router is named SCC and the nodes are named LCC0 and LCC2. The routing matrix with a TX Matrix router is acting as a provider edge (PE) router in a Layer 2 circuit network. SONET interface so-1/1/0 in node LCC0 connects to an IP/MPLS core network, and Asynchronous Transfer Mode 2 (ATM2) intelligent queuing (IQ) interface at-17/1/0 in node LCC2 runs Layer 2 circuit trunk mode to connect to an ATM switch. (For more information about Layer 2 see the Junos VPNs Configuration Guide.)
Figure 1: Routing Matrix with a TX Matrix Router Topology Diagram
Some key considerations for this configuration are as follows:
- Treat the routing matrix like a single router and execute all configuration and operational commands on the TX Matrix router SCC.
- Create configuration groups for each Routing Engine in the routing matrix by using groups re0, re1, lcc0-re0, lcc2-re0, lcc0-re1, and lcc2-re1. In the groups, configure hostnames, default routes, and management interfaces.
- To configure interfaces, use the routing matrix FPC numbering convention of slots 0 through 31.
- To enable ATM2 IQ trunk mode and other chassis-based commands, include the lcc lcc-number statement at the [edit chassis] hierarchy level and use the hardware FPC slot numbers 0 through 7 of node LCC2.
- Configure most other processes as usual, such as routing, class of service (CoS), and firewalls.
TX Matrix Router—SCC
[edit] groups { # You
can create special configuration groups in a routing matrix. re0 { # This
group corresponds to the master Routing Engine.system { # on the TX Matrix router.host-name scc;backup-router 192.168.17.254;}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.158/21;}}}}} re1 { # This
group corresponds to the backup Routing Enginesystem { # on the TX Matrix router.host-name scc1;backup-router 192.168.17.254;}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.168/21;}}}}} lcc0-re0 { # This group corresponds to the master Routing Enginesystem { # on the T640 router LCC0.host-name lcc0;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.157/21;}}}}} lcc2-re0 { #
This group corresponds to the master Routing Enginesystem { # on the T640 router LCC2.host-name lcc2;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.159/21;}}}}} lcc0-re1 { #
This group corresponds to the backup Routing Engine system { # on the T640 router LCC0.host-name lcc0-1;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.169/21;}}}}} lcc2-re1 { #
This group corresponds to the backup Routing Enginesystem { # on the T640 routing node LCC2.host-name lcc2-1;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.192/21;}}}}}}apply-groups [ re0 re1 lcc0-re1 lcc2-re1 lcc0-re0 lcc2-re0
];system {syslog {file messages {any any;}}} chassis { # You
must apply chassis commands to a specific T640 router. lcc 2 { # Specify
the T640 router and the FPC hardware slot of the node. fpc 1 { #
This FPC is equivalent to slot 17 in the routing matrix.pic 1 {atm-l2circuit-mode {trunk nni;}}}}}interfaces {so-1/1/0 { # This is a SONET interface at FPC 1, PIC 1,
port 0mtu 9192; # on the T640 router LCC0.unit 0 {family inet {address 10.15.1.1/30 {destination 10.15.1.2;}}family iso;family mpls {filter {input filter_1;}}}}at-17/1/0 { # This is an ATM2 IQ interface at FPC 1, PIC
1, port 0encapsulation atm-ccc-cell-relay; # on the T640 router
LCC2.atm-options {pic-type atm2;scheduler-maps { # CoS on an ATM2 IQ PIC works the same
in a routing matrix.cos1 { # as it does in a standalone T640 router.forwarding-class ubr {priority low;transmit-weight percent 25;}forwarding-class nrtvbr {priority low;transmit-weight percent 25;}forwarding-class rtvbr {priority low;transmit-weight percent 25;}forwarding-class cbr {priority high;transmit-weight percent 25;}}cos2 {forwarding-class ubr {priority low;transmit-weight percent 10;}forwarding-class nrtvbr {priority low;transmit-weight percent 20;}forwarding-class rtvbr {priority low;transmit-weight percent 30;}forwarding-class cbr {priority high;transmit-weight percent 40;}}cos3 {forwarding-class ubr {priority low;transmit-weight percent 40;}forwarding-class nrtvbr {priority low;transmit-weight percent 30;}forwarding-class rtvbr {priority low;transmit-weight percent 20;}forwarding-class cbr {priority high;transmit-weight percent 10;}}}}unit 0 {trunk-id 0;trunk-bandwidth 10m;cell-bundle-size 2;}unit 1 {trunk-id 1;trunk-bandwidth 10m;cell-bundle-size 1;atm-scheduler-map cos1;}unit 2 {trunk-id 2;trunk-bandwidth 10m;cell-bundle-size 2;atm-scheduler-map cos2;}unit 3 {trunk-id 3;trunk-bandwidth 10m;cell-bundle-size 3;atm-scheduler-map cos3;}}lo0 {unit 0 {family inet {address 127.0.0.1/32;address 10.255.77.158/32 {primary;}}family iso {address 47.0005.80ff.f800.0000.0108.0001.0102.5507.0158.00;}family inet6 {address 2001:db8::10:255:77:158/32 {primary;}}}}} protocols { #
You can configure protocols in the routing matrix as usual.mpls {interface so-1/1/0.0;}isis {interface so-1/1/0.0;interface lo0.0;}ldp {interface so-1/1/0.0;interface lo0.0;}l2circuit {neighbor 10.255.71.97 {interface at-17/1/0.0 {virtual-circuit-id 100;}interface at-17/1/0.1 {virtual-circuit-id 101;}interface at-17/1/0.2 {virtual-circuit-id 102;}interface at-17/1/0.3 {virtual-circuit-id 103;}}}} class-of-service { # You can configure CoS in the routing matrix as usual.forwarding-classes {queue 0 ubr;queue 1 nrtvbr;queue 2 rtvbr;queue 3 cbr;}traceoptions {flag all;}} firewall { #
You can configure firewalls in the routing matrix as usual.family mpls {filter filter_1 {term plp0 {from {exp [ 0 2 4 6 ];}then {count LOW;loss-priority low;}}term plp1 {from {exp [ 1 3 5 7 ];}then {count HIGH;loss-priority high;}}}}}
Verifying Your Work on the Routing Matrix with a TX Matrix Router
To verify proper operation of the routing matrix with a TX Matrix router, use the following commands on the TX Matrix router:
- show chassis alarms <lcc lcc-number | scc>
- show chassis craft-interface <lcc lcc-number | scc>
- show chassis ethernet-switch <lcc lcc-number | scc>
- show chassis hardware <lcc lcc-number | scc>
- show chassis fpc <lcc lcc-number>
- show chassis lccs
- show chassis location <fpc | interface | lcc lcc-number | scc>
- show chassis routing-engine <lcc lcc-number | scc>
- show chassis sibs <lcc lcc-number | scc>
- show interfaces terse
- show route summary
- show system uptime <all-lcc | lcc lcc-number | scc>
- show version <all-lcc | lcc lcc-number | scc>
In general, when you issue standard operational commands on a TX Matrix router, you receive output from the primary Routing Engines of all components in the routing matrix. To limit the output of information for a specific T640 router within the routing matrix, include the lcc lcc-number option. To display information for the TX Matrix router only, include the scc option. To display information for all T640 routers within the routing matrix (selected commands only), include the all-lcc option. Any exceptions to this general rule are mentioned next to the appropriate commands.
The following sections show the output of select operational commands used with the configuration example:
- Displaying the Software Version on A Routing Matrix with a TX Matrix Router
- Displaying Interfaces
- Displaying Routes
- Displaying Alarms and System Uptime
- Displaying Chassis Hardware and Status for a Routing Matrix with a TX Matrix Router
Displaying the Software Version on A Routing Matrix with a TX Matrix Router
The show version command provides an excellent example of how you can select output for various components of the routing matrix with a TX Matrix router. If the TX Matrix router (SCC) or a T640 router (LCC) is not specified in the command, then the command displays output for all components.
user@router> show version ?
Possible completions: <[Enter]> Execute this command all-lcc Show software version on all LCC chassis brief Display brief output detail Display detailed output lcc Show software version on specific LCC (0..3) scc Show software version on the SCC | Pipe through a command
To display the software version for all routing matrix components, issue the show version command on the TX Matrix router:
user@router> show version
scc-re0: -------------------------------------------------------------------------- Hostname: scc Model: TX Matrix JUNOS Base OS boot [7.0-20040630.0] JUNOS Base OS Software Suite [7.0-20040629.0] JUNOS Kernel Software Suite [7.0-20040630.0] JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0] JUNOS Routing Software Suite [7.0-20040630.0] JUNOS Online Documentation [7.0-20040630.0] JUNOS Crypto Software Suite [7.0-20040630.0] lcc0-re0: -------------------------------------------------------------------------- Hostname: lcc0 Model: t640 JUNOS Base OS boot [7.0-20040630.0] JUNOS Base OS Software Suite [7.0-20040629.0] JUNOS Kernel Software Suite [7.0-20040630.0] JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0] JUNOS Routing Software Suite [7.0-20040630.0] JUNOS Online Documentation [7.0-20040630.0] JUNOS Crypto Software Suite [7.0-20040630.0] JUNOS Support Tools Package [7.0-20040630.0] lcc2-re0: -------------------------------------------------------------------------- Hostname: lcc2 Model: t640 JUNOS Base OS boot [7.0-20040630.0] JUNOS Base OS Software Suite [7.0-20040629.0] JUNOS Kernel Software Suite [7.0-20040630.0] JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0] JUNOS Routing Software Suite [7.0-20040630.0] JUNOS Online Documentation [7.0-20040630.0] JUNOS Crypto Software Suite [7.0-20040630.0]
JUNOS Support Tools Package [7.0-20040630.0]
To display the software version for the TX Matrix router only, include the scc option:
user@router> show version scc
Hostname: scc Model: TX Matrix JUNOS Base OS boot [7.0-20040630.0] JUNOS Base OS Software Suite [7.0-20040629.0] JUNOS Kernel Software Suite [7.0-20040630.0] JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0] JUNOS Routing Software Suite [7.0-20040630.0] JUNOS Online Documentation [7.0-20040630.0] JUNOS Crypto Software Suite [7.0-20040630.0]
To display the software version for a specific T640 router, include the lcc option:
user@router> show version lcc 0 lcc0-re0: -------------------------------------------------------------------------- Hostname: lcc0 Model: t640 JUNOS Base OS boot [7.0-20040630.0] JUNOS Base OS Software Suite [7.0-20040629.0] JUNOS Kernel Software Suite [7.0-20040630.0] JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0] JUNOS Routing Software Suite [7.0-20040630.0] JUNOS Online Documentation [7.0-20040630.0] JUNOS Crypto Software Suite [7.0-20040630.0] JUNOS Support Tools Package [7.0-20040630.0]
To display the output for all T640 routers, include the all-lcc option:
user@router> show version all-lcc lcc0-re0: -------------------------------------------------------------------------- Hostname: lcc0 Model: t640 JUNOS Base OS boot [7.0-20040630.0] JUNOS Base OS Software Suite [7.0-20040629.0] JUNOS Kernel Software Suite [7.0-20040630.0] JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0] JUNOS Routing Software Suite [7.0-20040630.0] JUNOS Online Documentation [7.0-20040630.0] JUNOS Crypto Software Suite [7.0-20040630.0] JUNOS Support Tools Package [7.0-20040630.0] lcc2-re0: -------------------------------------------------------------------------- Hostname: lcc2 Model: t640 JUNOS Base OS boot [7.0-20040630.0] JUNOS Base OS Software Suite [7.0-20040629.0] JUNOS Kernel Software Suite [7.0-20040630.0] JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0] JUNOS Routing Software Suite [7.0-20040630.0] JUNOS Online Documentation [7.0-20040630.0] JUNOS Crypto Software Suite [7.0-20040630.0] JUNOS Support Tools Package [7.0-20040630.0]
Displaying Interfaces
Although individual FPCs are installed in each of the T640 routers, the routing matrix is designed to collect interface information centrally at the TX Matrix router. To display available interfaces in the routing matrix, issue a show interfaces command on the TX Matrix router:
user@router> show interfaces terse Interface Admin Link Proto Local Remote
so-1/0/0 up up
so-1/1/0 up up
so-1/1/0.0 up up inet 10.15.1.1 --> 10.15.1.2
iso
mpls
so-1/3/0 up down
at-2/1/0 up up
ge-2/2/0 up up
so-3/3/0 up up
so-3/3/1 up up
so-3/3/2 up down
so-3/3/3 up down
so-16/0/0 up down
so-16/0/1 up down
so-16/0/2 up down
so-16/0/3 up up
ge-16/1/0 up down
so-17/0/0 up down
at-17/1/0 up up
at-17/1/0.0 up up ccc
at-17/1/0.1 up up ccc
at-17/1/0.2 up up ccc
at-17/1/0.3 up up ccc
at-17/1/1 up up
ge-17/2/0 up up
ge-17/2/1 up up
so-17/3/0 up down
so-19/0/0 up down
so-19/1/0 up down
so-19/2/0 up down
so-19/3/0 up down
bcm0 up up
bcm0.0 up up tnp 4
dsc up up
em0 up up
em0.0 up up tnp 4
fxp0 up up
fxp0.0 up up inet 192.168.77.158/21
gre up up
ipip up up
lo0 up up
lo0.0 up up inet 10.255.70.158 --> 0/0
127.0.0.1 --> 0/0
iso 47.0005.80ff.f800.0000.0108.0001.0102.5507.0158.00
inet6 2001:db8::10:255:70:158
fe80::280:42ff:fe13:269d
lo0.16385 up up inet
inet6 fe80::280:42ff:fe13:269d
lsi up up
mtun up up
pimd up up
pime up up
tap up up
Displaying Routes
When you need to verify route information for a routing matrix, you must issue operational commands on the TX Matrix router. To display available routes for the routing matrix, issue a show route command:
user@router> show route summary Router ID: 10.255.77.158
inet.0: 13 destinations, 14 routes (12 active, 0 holddown, 1 hidden)
Direct: 4 routes, 3 active
Local: 2 routes, 2 active
Static: 6 routes, 6 active
IS-IS: 2 routes, 1 active
inet.3: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
LDP: 1 routes, 1 active
iso.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
Direct: 1 routes, 1 active
mpls.0: 7 destinations, 7 routes (7 active, 0 holddown, 0 hidden)
MPLS: 3 routes, 3 active
LDP: 2 routes, 2 active
L2CKT: 2 routes, 2 active
inet6.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)
Direct: 2 routes, 2 active
__juniper_private1__.inet6.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
Direct: 1 routes, 1 active
l2circuit.0: 5 destinations, 5 routes (5 active, 0 holddown, 0 hidden)
LDP: 1 routes, 1 active
L2CKT: 4 routes, 4 active
Displaying Alarms and System Uptime
To display alarms for all routing matrix components, issue the show chassis alarms command:
user@router> show chassis alarms scc-re0: -------------------------------------------------------------------------- 2 alarms currently active Alarm time Class Description 2004-09-27 08:50:57 PDT Major LCC 2 Major Errors 2004-09-27 08:50:42 PDT Minor LCC 0 Minor Errors lcc0-re0: -------------------------------------------------------------------------- 1 alarms currently active Alarm time Class Description 2004-09-27 08:50:42 PDT Minor PEM 1 Absent lcc2-re0: -------------------------------------------------------------------------- 1 alarms currently active Alarm time Class Description 2004-09-27 08:50:57 PDT Major PEM 1 Not OK
To display the craft interface display for all routing matrix components, issue the show chassis craft-interface command:
user@router> show chassis craft-interface scc-re0:
--------------------------------------------------------------------------
FPM Display contents:
+--------------------+
|scc |
|2 Alarms active |
|R: LCC 2 Major Error|
|Y: LCC 0 Minor Error|
+--------------------|
Front Panel System LEDs:
Routing Engine 0 1
--------------------------
OK * *
Fail . .
Master * .
Front Panel Alarm Indicators:
-----------------------------
Red LED *
Yellow LED *
Major relay *
Minor relay *
CB LEDs:
CB 0 1
--------------
Amber . .
Green * *
Blue * .
SIB LEDs:
SIB 0 1 2 3 4
--------------------------
Fail . . . . .
OK * * * * *
Active . * * * *
lcc0-re0:
--------------------------------------------------------------------------
FPM Display contents:
+--------------------+
|lcc0 |
|1 Alarm active |
|Y: PEM 1 Absent |
| |
+--------------------|
Front Panel System LEDs:
Routing Engine 0 1
--------------------------
OK * *
Fail . .
Master * .
Front Panel Alarm Indicators:
-----------------------------
Red LED .
Yellow LED *
Major relay .
Minor relay *
Front Panel FPC LEDs:
FPC 0 1 2 3 4 5 6 7
------------------------------------
Red . . . . . . . .
Green . * * * . . . .
CB LEDs:
CB 0 1
--------------
Amber . .
Green * *
Blue * .
SCG LEDs:
SCG 0 1
--------------
Amber . .
Green * *
Blue * .
SIB LEDs:
SIB 0 1 2 3 4
--------------------------
Red . . . . .
Green * * * * *
lcc2-re0:
--------------------------------------------------------------------------
FPM Display contents:
+--------------------+
|lcc2 |
|1 Alarm active |
|R: PEM 1 Not OK |
| |
+--------------------|
Front Panel System LEDs:
Routing Engine 0 1
--------------------------
OK * *
Fail . .
Master * .
Front Panel Alarm Indicators:
-----------------------------
Red LED *
Yellow LED .
Major relay *
Minor relay .
Front Panel FPC LEDs:
FPC 0 1 2 3 4 5 6 7
------------------------------------
Red . . . . . . . .
Green * * . * . . . .
CB LEDs:
CB 0 1
--------------
Amber . .
Green * *
Blue * .
SCG LEDs:
SCG 0 1
--------------
Amber . .
Green * .
Blue * .
SIB LEDs:
SIB 0 1 2 3 4
--------------------------
Red . . . . .
Green * * * * *
To display the amount of time the routing matrix components have been in operation, issue the show system uptime command on the TX Matrix router:
user@router> show system uptime scc-re0: -------------------------------------------------------------------------- Current time: 2004-09-27 09:44:55 PDT System booted: 2004-09-27 08:49:31 PDT (00:55:24 ago) Protocols started: 2004-09-27 08:50:27 PDT (00:54:28 ago) Last configured: 2004-09-27 09:16:08 PDT (00:28:47 ago) by regress 9:44AM PDT up 55 mins, 1 user, load averages: 0.00, 0.05, 0.06 lcc0-re0: -------------------------------------------------------------------------- Current time: 2004-09-27 09:44:55 PDT System booted: 2004-09-27 08:49:24 PDT (00:55:31 ago) Last configured: 2004-09-27 09:16:06 PDT (00:28:49 ago) by regress 9:44AM PDT up 56 mins, 0 users, load averages: 0.00, 0.02, 0.00 lcc2-re0: -------------------------------------------------------------------------- Current time: 2004-09-27 09:44:55 PDT System booted: 2004-09-27 08:49:26 PDT (00:55:29 ago) Last configured: 2004-09-27 09:16:06 PDT (00:28:49 ago) by regress 9:44AM PDT up 55 mins, 0 users, load averages: 0.02, 0.01, 0.00
Displaying Chassis Hardware and Status for a Routing Matrix with a TX Matrix Router
To display the hardware inventory for a routing matrix with a TX Matrix router, you can select output for the TX Matrix router only, a specific T640 router, or all components. If a specific component (lcc or scc) is not specified as an option in the command, the default output displays information for the entire routing matrix.
user@router> show chassis hardware ? Possible completions: <[Enter]> Execute this command detail Include RAM and disk information in output extensive Display ID EEPROM information frus Display assembly IDs and extra PIC information lcc Display chassis-specific information (0..3) scc Display chassis-specific information | Pipe through a command
To display all hardware components in a routing matrix, issue the show chassis hardware command on the TX Matrix router:
user@router> show chassis hardware scc-re0:
--------------------------------------------------------------------------
Hardware inventory:
Item Version Part number Serial number Description
Chassis TX Matrix
Midplane REV 04 710-004396 RB0013 SCC Midplane
FPM GBUS
FPM Display REV 04 710-004619 HS5953 SCC FPM
CIP 0 REV 01 710-010218 HS5726 SCC CIP
CIP 1 REV 01 710-010218 HV9163 SCC CIP
PEM 0 Rev 11 740-002595 pm18529 Power Entry Module
Routing Engine 0 REV 02 740-008883 212058900121 RE-4.0
Routing Engine 1 REV 03 740-008883 211123900258 RE-4.0
CB 0 REV 01 710-011709 HS5911 Control Board (CB-TX)
CB 1 REV 01 710-011709 HZ2163 Control Board (CB-TX)
SPMB 0 REV 09 710-003229 HT4129 T-series Switch CPU
SPMB 1 REV 09 710-003229 HT4174 T-series Switch CPU
SIB 0 REV 01 710-011223 HS0663 SIB-S8-F16 1/2
B Board REV 05 710-011225 HW1210 SIB-S8-F16 1/2 (B)
SIB 1 REV 01 710-005839 HW1160 SIB-S8-F16
B Board REV 01 710-005840 HW1213 SIB-S8-F16 (B)
SIB 2 REV 05 710-011223 HW1146 SIB-S8-F16 1/2
B Board REV 05 710-011225 JB8148 SIB-S8-F16 1/2 (B)
SIB 3 REV 05 710-011223 HW1218 SIB-S8-F16 1/2
B Board REV 05 710-011225 HW1214 SIB-S8-F16 1/2 (B)
SIB 4 REV 05 710-011223 HW1162 SIB-S8-F16 1/2
B Board REV 05 710-011225 HW1182 SIB-S8-F16 1/2 (B)
lcc0-re0:
--------------------------------------------------------------------------
Hardware inventory:
Item Version Part number Serial number Description
Chassis 65409 T640
Midplane REV 03 710-005608 RA1395 T640 Backplane
FPM GBUS REV 09 710-002901 RA2649 T640 FPM Board
FPM Display REV 05 710-002897 RA2608 FPM Display
CIP REV 06 710-002895 HS0753 T-series CIP
PEM 0 Rev 01 740-002595 MF16629 Power Entry Module
SCG 0 REV 11 710-003423 HS4313 T640 Sonet Clock Gen.
SCG 1 REV 11 710-003423 HR9161 T640 Sonet Clock Gen.
Routing Engine 0 REV 03 740-008883 211123900199 RE-4.0
Routing Engine 1 REV 03 740-008883 211123900248 RE-4.0
CB 0 REV 02 710-007655 HS5909 Control Board (CB-T)
CB 1 REV 02 710-007655 HS5910 Control Board (CB-T)
FPC 1 REV 07 710-007527 HR0716 FPC Type 2
CPU REV 15 710-001726 HS6048 FPC CPU
PIC 0 REV 07 750-001900 AR3722 1x OC-48 SONET, SMSR
PIC 1 REV 05 750-001900 AD3644 1x OC-48 SONET, SMSR
PIC 3 REV 06 750-001900 HD7603 1x OC-48 SONET, SMSR
MMB 1 REV 03 710-005555 HT5273 MMB-288mbit
PPB 0 REV 04 710-003758 HR4249 PPB Type 2
PPB 1 REV 04 710-003758 HR4257 PPB Type 2
FPC 2 REV 01 710-010233 HM4189 E-FPC Type 1
CPU REV 01 710-010169 HS9936 FPC CPU-Enhanced
PIC 1 REV 03 750-005719 HL8326 1x OC-12 ATM-II IQ, MM
PIC 2 REV 01 750-003141 AD9051 1x G/E, 1000 BASE-SX
MMB 1 REV 01 710-008923 HR0848 MMB 3M 288-bit
FPC 3 REV 01 710-010154 HR0863 E-FPC Type 3
CPU REV 01 710-010169 HN3422 FPC CPU-Enhanced
PIC 3 REV 01 750-009553 HP3576 4x OC-48 SONET
SFP 0 REV 01 740-009030 P11H5N1 SFP-LR
SFP 1 REV 01 740-009029 35D464P00060 SFP-IR
SFP 3 REV 01 740-009030 P11H5LM SFP-LR
MMB 0 REV 01 710-010171 HR0821 MMB-288mbit
MMB 1 REV 01 710-010171 HR0818 MMB-288mbit
SPMB 0 REV 09 710-003229 HT4177 T-series Switch CPU
SPMB 1 REV 09 710-003229 HT4176 T-series Switch CPU
SIB 0 REV 07 710-005781 HR5939 SIB-L8-F16
B Board REV 06 710-005782 HR5944 SIB-L8-F16 (B)
SIB 1 REV 02 710-005781 HZ2146 SIB-L8-F16
B Board REV 03 710-005782 HY4160 SIB-L8-F16 (B)
SIB 2 REV 07 710-005781 HR5925 SIB-L8-F16
B Board REV 03 710-005782 HY4161 SIB-L8-F16 (B)
SIB 3 REV 07 710-005781 HR5918 SIB-L8-F16
B Board REV 06 710-005782 HR5972 SIB-L8-F16 (B)
SIB 4 REV 07 710-005781 HR5935 SIB-L8-F16
B Board REV 06 710-005782 HR5969 SIB-L8-F16 (B)
lcc2-re0:
--------------------------------------------------------------------------
Hardware inventory:
Item Version Part number Serial number Description
Chassis 55609 T640
Midplane REV 03 710-005608 RA1444 T640 Backplane
FPM GBUS REV 09 710-002901 RA3309 T640 FPM Board
FPM Display REV 05 710-002897 RA3273 FPM Display
CIP REV 06 710-002895 HS0735 T-series CIP
PEM 0 Rev 11 740-002595 PM18568 Power Entry Module
PEM 1 Rev 11 740-002595 PM18572 Power Entry Module
SCG 0 REV 11 710-003423 HS9991 T640 Sonet Clock Gen.
Routing Engine 0 REV 03 740-008883 211123900183 RE-4.0
Routing Engine 1 REV 02 740-008883 212058900178 RE-4.0
CB 0 REV 02 710-007655 HS5913 Control Board (CB-T)
CB 1 REV 02 710-007655 HS5944 Control Board (CB-T)
FPC 0 REV 05 710-001721 HD5965 FPC Type 3
CPU REV 09 710-001726 AY4909 FPC CPU
PIC 0 REV 04 750-009553 HV3648 4x OC-48 SONET
SFP 0 REV 01 740-009029 P11JXWP SFP-IR
SFP 1 REV 01 740-008169 36D525P00154 UNKNOWN
SFP 2 REV 01 740-009028 2353110 SFP-SR
SFP 3 REV 01 740-008169 36D525P00159 UNKNOWN
PIC 1 REV 02 750-009567 HX2875 1x 10GE(LAN),XENPAK
SFP 0 REV 01 740-009898 USC202YW25 XENPAK-LR
MMB 0 REV 03 710-004047 HE3427 MMB-288mbit
MMB 1 REV 03 710-004047 HD5812 MMB-288mbit
ICBM REV 04 710-003384 HB1884 FPC ICBM
PPB 0 REV 02 710-002845 HC0964 PPB Type 3
PPB 1 REV 02 710-002845 HC0987 PPB Type 3
FPC 1 REV 02 710-002385 HC0618 FPC Type 2
CPU REV 06 710-001726 HA4724 FPC CPU
PIC 0 REV 02 750-009066 HL9900 1x OC-48 SONET SFP
SFP 0 NON-JNPR P11QS8W SFP-LR
PIC 1 REV 02 750-007219 AZ1339 2x OC-12 ATM-II IQ, MM
PIC 2 REV 02 750-002510 AP7476 2x G/E, 1000 BASE-SX
PIC 3 REV 05 750-001900 AD5738 1x OC-48 SONET, SMSR
MMB 1 REV 03 710-004047 HD5829 MMB-288mbit
ICBM REV 04 710-003384 HC0386 FPC ICBM
PPB 0 REV 02 710-003758 HC0904 PPB Type 2
PPB 1 REV 02 710-003758 HC0898 PPB Type 2
FPC 3 REV 07 710-007529 HR3311 FPC Type 3
CPU REV 15 710-001726 HR2788 FPC CPU
PIC 0 REV 10 750-004535 HT0545 1x OC-192 SM SR2
PIC 1 REV 12 750-004535 HX2065 1x OC-192 SM SR2
PIC 2 REV 01 750-004535 HC0241 1x OC-192 SM SR1
PIC 3 REV 01 750-004535 HF6583 1x OC-192 SM SR1
MMB 0 REV 03 710-005555 HR5642 MMB-288mbit
MMB 1 REV 03 710-005555 HR5586 MMB-288mbit
PPB 0 REV 04 710-002845 HT6719 PPB Type 3
PPB 1 REV 04 710-002845 HM0206 PPB Type 3
SPMB 0 REV 09 710-003229 HR8685 T-series Switch CPU
SPMB 1 REV 09 710-003229 HR3730 T-series Switch CPU
SIB 0 REV 07 710-005781 HR5937 SIB-L8-F16
B Board REV 06 710-005782 HZ5288 SIB-L8-F16 (B)
SIB 1 REV 07 710-005781 HZ5279 SIB-L8-F16
B Board REV 06 710-005782 HR5951 SIB-L8-F16 (B)
SIB 2 REV 07 710-005781 HZ5276 SIB-L8-F16
B Board REV 06 710-005782 HR5950 SIB-L8-F16 (B)
SIB 3 REV 07 710-005781 HR5915 SIB-L8-F16
B Board REV 06 710-005782 HZ5285 SIB-L8-F16 (B)
SIB 4 REV 07 710-005781 HR5934 SIB-L8-F16
B Board REV 06 710-005782 HR5952 SIB-L8-F16 (B)
You can also display individual hardware components in the TX Matrix router, a specific T640 router, or the entire routing matrix. To display all the SIBs in the entire routing matrix, issue the show chassis sibs command on the TX Matrix router.
user@router> show chassis sibsscc-re0: -------------------------------------------------------------------------- Slot State Uptime 0 Spare 1 Online 53 minutes, 38 seconds 2 Online 53 minutes, 36 seconds 3 Online 53 minutes, 33 seconds 4 Online 53 minutes, 30 seconds lcc0-re0: -------------------------------------------------------------------------- Slot State Uptime 0 Spare 1 Online 53 minutes, 18 seconds 2 Online 53 minutes, 17 seconds 3 Online 53 minutes, 16 seconds 4 Online 53 minutes, 15 seconds lcc2-re0: -------------------------------------------------------------------------- Slot State Uptime 0 Spare 1 Online 53 minutes, 18 seconds 2 Online 53 minutes, 17 seconds 3 Online 53 minutes, 16 seconds 4 Online 53 minutes, 15 seconds
To display information about all master Routing Engines in the routing matrix, issue the show chassis routing-engine command on the TX Matrix router:
user@router> show chassis routing-enginescc-re0:
--------------------------------------------------------------------------
Routing Engine status:
Slot 0:
Current state Master
Election priority Master (default)
Temperature 34 degrees C / 93 degrees F
CPU temperature 35 degrees C / 95 degrees F
DRAM 2048 MB
Memory utilization 12 percent
CPU utilization:
User 0 percent
Background 0 percent
Kernel 5 percent
Interrupt 0 percent
Idle 95 percent
Model RE-4.0
Serial ID 212058900121
Start time 2004-09-27 08:49:31 PDT
Uptime 1 hour, 4 seconds
Load averages: 1 minute 5 minute 15 minute
0.06 0.04 0.05
Routing Engine status:
Slot 1:
Current state Backup
Election priority Backup (default)
Temperature 33 degrees C / 91 degrees F
CPU temperature 34 degrees C / 93 degrees F
DRAM 2048 MB
Memory utilization 10 percent
CPU utilization:
User 0 percent
Background 0 percent
Kernel 0 percent
Interrupt 1 percent
Idle 99 percent
Model RE-4.0
Serial ID 211123900258
Start time 2004-09-26 13:09:13 PDT
Uptime 20 hours, 40 minutes, 4 seconds
lcc0-re0:
--------------------------------------------------------------------------
Routing Engine status:
Slot 0:
Current state Master
Election priority Master (default)
Temperature 37 degrees C / 98 degrees F
CPU temperature 38 degrees C / 100 degrees F
DRAM 2048 MB
Memory utilization 11 percent
CPU utilization:
User 0 percent
Background 0 percent
Kernel 3 percent
Interrupt 1 percent
Idle 97 percent
Model RE-4.0
Serial ID 211123900199
Start time 2004-09-27 08:49:24 PDT
Uptime 1 hour, 11 seconds
Load averages: 1 minute 5 minute 15 minute
0.02 0.02 0.00
Routing Engine status:
Slot 1:
Current state Backup
Election priority Backup (default)
Temperature 35 degrees C / 95 degrees F
CPU temperature 35 degrees C / 95 degrees F
DRAM 2048 MB
Memory utilization 10 percent
CPU utilization:
User 0 percent
Background 0 percent
Kernel 0 percent
Interrupt 0 percent
Idle 99 percent
Model RE-4.0
Serial ID 211123900248
Start time 2004-09-26 13:09:07 PDT
Uptime 20 hours, 40 minutes, 12 seconds
lcc2-re0:
--------------------------------------------------------------------------
Routing Engine status:
Slot 0:
Current state Master
Election priority Master (default)
Temperature 33 degrees C / 91 degrees F
CPU temperature 35 degrees C / 95 degrees F
DRAM 2048 MB
Memory utilization 11 percent
CPU utilization:
User 0 percent
Background 0 percent
Kernel 4 percent
Interrupt 0 percent
Idle 96 percent
Model RE-4.0
Serial ID 211123900183
Start time 2004-09-27 08:49:26 PDT
Uptime 1 hour, 9 seconds
Load averages: 1 minute 5 minute 15 minute
0.15 0.05 0.01
Routing Engine status:
Slot 1:
Current state Backup
Election priority Backup (default)
Temperature 32 degrees C / 89 degrees F
CPU temperature 34 degrees C / 93 degrees F
DRAM 2048 MB
Memory utilization 10 percent
CPU utilization:
User 0 percent
Background 0 percent
Kernel 0 percent
Interrupt 1 percent
Idle 99 percent
Model RE-4.0
Serial ID 212058900178
Start time 2004-09-26 13:09:10 PDT
Uptime 20 hours, 40 minutes, 8 seconds
To display information about FPCs in a routing matrix, issue the show chassis fpc command. Because there are no FPCs in a TX Matrix router, there is no scc option available for this command.
user@router> show chassis fpc
lcc0-re0:
--------------------------------------------------------------------------
Temp CPU Utilization (%) Memory Utilization (%)
Slot State (C) Total Interrupt DRAM (MB) Heap Buffer
0 Empty
1 Online 31 1 0 256 7 44
2 Online 28 1 0 256 7 44
3 Online 31 3 0 256 14 44
4 Empty
5 Empty
6 Empty
7 Empty
lcc2-re0:
--------------------------------------------------------------------------
Temp CPU Utilization (%) Memory Utilization (%)
Slot State (C) Total Interrupt DRAM (MB) Heap Buffer
0 Online 31 3 0 256 14 44
1 Online 30 2 0 256 7 44
2 Empty
3 Online 31 3 0 256 14 44
4 Empty
5 Empty
6 Empty
7 Empty
You can also check to see if the TX Matrix router and T640 routers are communicating correctly within the routing matrix. To verify that the T640 routers have proper connectivity to the routing matrix, issue the show chassis lccs command. In this example, there are two T640 routers in the routing matrix.
user@router> show chassis lccs Slot State Uptime 0 Online 52 minutes, 5 seconds 1 Empty 2 Online 52 minutes, 6 seconds 3 Empty
