Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Managed Objects for jnxSoamLmCurrentStatsTable

    The jnxSoamLmCurrentStatsTable, whose object identifier is {jnxSoamPmLmObjects 3}, contains the jnxSoamLmCurrentStatsEntry that signifies the Ethernet loss measurement (ETH-LM) historical statistical details. Each jnxSoamLmCurrentStatsEntry, whose object identifier is {jnxSoamLmCurrentStatsTable 1}, contains the objects listed in the following table.

    The jnxSoamLmCurrentStatsTable contains the results for the current Measurement Interval in a SOAM Loss Measurement session gathered during the interval indicated by iterator counts. A row in this table is created automatically by the SNMP Agent when the Loss Measurement session is configured. Each row in the table represents the current statistics for a Loss Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. There may be more than one LM session per MEP. The main use case for this is to allow multiple CoS instances to be operating simultaneously for a MEP. The objects in this table apply regardless of the value of jnxSoamLmCfgType unless otherwise specified in the object description. Except for jnxSoamLmCurrentStatsIndex, jnxSoamLmCurrentStatsStartTime, jnxSoamLmCurrentStatsElapsedTime and jnxSoamLmCurrentStatsSuspect, each object in this table applies only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable. The objects in this table do not need to be persistent upon reboot or restart of a device.

    Table 1: jnxSoamLmCurrentStatsTable

    Object

    Object ID

    Description

    jnxSoamLmCurrentStatsIndex

    jnxSoamLmCurrentStatsEntry 1

    Specifies the index for the Measurement Interval within this PM session. This value will become the value for jnxSoamLmHistoryStatsIndex once the Measurement Interval is completed.

    Measurement Interval indexes are assigned sequentially by the SNMP Agent. The first Measurement Interval that occurs after the session is started is assigned index 1.

    jnxSoamLmCurrentStatsStartTime

    jnxSoamLmCurrentStatsEntry 2

    Specifies the time at which the Measurement Interval started.

    jnxSoamLmCurrentStatsElapsedTime

    jnxSoamLmCurrentStatsEntry 3

    Specifies the length of time for which the Measurement Interval has been running, in 0.01 seconds.

    jnxSoamLmCurrentStatsSuspect

    jnxSoamLmCurrentStatsEntry 4

    Indicates whether the Measurement Interval has been marked as suspect. The object is set to false at the start of a measurement interval. It is set to true when there is a discontinuity in the performance measurements during the Measurement Interval. Conditions for a discontinuity include, but are not limited to the following:

    1—The local time-of-day clock is adjusted by at least 10 seconds

    2—The conducting of a performance measurement is halted before the current Measurement Interval is completed

    3—A local test, failure, or reconfiguration that disrupts service

    jnxSoamLmCurrentStatsForwardTransmittedFrames

    jnxSoamLmCurrentStatsEntry 5

    Contains the number of frames transmitted in the forward direction by this MEP. For a PM Session of types lmLmm and lmCcm, this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of type lmSlm, this includes the count of OAM ETH-SLM frames only.

    jnxSoamLmCurrentStatsForwardReceivedFrames

    jnxSoamLmCurrentStatsEntry 6

    Contains the number of frames received in the forward direction by this MEP. For a PM Session of types lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of type lmSlm this includes the count of OAM ETH-SLM frames only.

    jnxSoamLmCurrentStatsForwardMinFlr

    jnxSoamLmCurrentStatsEntry 7

    Contains the minimum one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

    jnxSoamLmCurrentStatsForwardMaxFlr

    jnxSoamLmCurrentStatsEntry 8

    Contains the maximum one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

    jnxSoamLmCurrentStatsForwardAvgFlr

    jnxSoamLmCurrentStatsEntry 9

    Contains the average one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

    jnxSoamLmCurrentStatsBackwardTransmittedFrames

    jnxSoamLmCurrentStatsEntry 10

    Contains the number of frames transmitted in the backward direction by this MEP. For a PM Session of type lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of types lmSlm this includes the count of SOAM ETH-SLM frames only.

    jnxSoamLmCurrentStatsBackwardReceivedFrames

    jnxSoamLmCurrentStatsEntry 11

    Contains the number of frames received in the backward direction by this MEP. For a PM Session of type lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of types lmSlm this includes the count of SOAM ETH-SLM frames only.

    jnxSoamLmCurrentStatsBackwardMinFlr

    jnxSoamLmCurrentStatsEntry 12

    Contains the minimum one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

    jnxSoamLmCurrentStatsBackwardMaxFlr

    jnxSoamLmCurrentStatsEntry 13

    Contains the maximum one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

    jnxSoamLmCurrentStatsBackwardAvgFlr

    jnxSoamLmCurrentStatsEntry 14

    Contains the average one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

    jnxSoamLmCurrentStatsSoamPdusSent

    jnxSoamLmCurrentStatsEntry 15

    Contains the count of the number of SOAM PDUs sent during this Measurement Interval. This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames transmitted.

    jnxSoamLmCurrentStatsSoamPdusReceived

    jnxSoamLmCurrentStatsEntry 16

    Contains the count of the number of SOAM PDUs received in this Measurement Interval. This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or lmCcm. This object indicates the number of LMR, CCM, or SLR SOAM frames received.

    Modified: 2017-09-13