Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

ping mpls l3vpn

 

Syntax

Release Information

Command introduced before Junos OS Release 7.4.

Command introduced in Junos OS Release 9.0 for EX Series switches.

The size and sweep options were introduced in Junos OS Release 9.6.

Statement introduced in Junos OS Release 12.3X50 for the QFX Series.

Statement introduced in Junos OS Release 14.1X53-D30 for QFX Virtual Chassis and Virtual Chassis Fabric.

Description

Check the operability of a MPLS Layer 3 virtual private network (VPN) connection. Type Ctrl+c to interrupt a ping mpls l3vpn command.

Options

bottom-label-ttl(Optional) Display the time-to-live value for the bottom label in the label stack.
count count(Optional) Number of ping requests to send. If count is not specified, five ping requests are sent. The range of values is 1 through 1,000,000. The default value is 5.
destination address(Optional) Specify an address other than the default (127.0.0.1/32) for the ping echo requests. The address can be anything within the 127/8 subnet.
detail(Optional) Display detailed information about the echo requests sent and received.
exp forwarding-class(Optional) Value of the forwarding class for the MPLS ping packets.
l3vpn-name(Optional) Layer 3 VPN name.
logical-system (all | logical-system-name)(Optional) Perform this operation on all logical systems or on the specified logical system.
prefix prefix-namePing to test whether a prefix is present in a provider edge (PE) router’s or switch's VPN routing and forwarding (VRF) table, by means of a Layer 3 VPN destination prefix. This option does not test the connection between a PE router or switch and a customer edge (CE) router or switch.
size bytes(Optional) Size of the label-switched path (LSP) ping request packet (96 through 65468 bytes). Packets are 4-byte aligned. For example, If you enter a size of 97, 98, 99, or 100, the router or switch uses a size value of 100 bytes. If you enter a packet size that is smaller than the minimum size, an error message is displayed reminding you of the 96-byte minimum.
source source-address(Optional) IP address of the outgoing interface. This address is sent in the IP source address field of the ping request. If this option is not specified, the default address is usually the loopback interface (lo.0).
sweep(Optional) Automatically determine the size of the maximum transmission unit (MTU).

Additional Information

You must configure MPLS at the [edit protocols mpls] hierarchy level on the egress PE router or switch (the router or switch receiving the MPLS echo packets) to ping a Layer 2 circuit.

In asymmetric MTU scenarios, the echo response might be dropped. For example, if the MTU from System A to System B is 1000 bytes, the MTU from System B to  System A is 500 bytes, and the ping request packet size is 1000 bytes, the echo response is dropped because the PAD TLV is included in the echo response, making it too large.

If the Layer 3 VPN traffic transits a route reflector within the network, the ping mpls l3vpn command does not work.

Required Privilege Level

network

List of Sample Output

ping mpls l3vpn

ping mpls l3vpn detail

Output Fields

When you enter this command, you are provided feedback on the status of your request. An exclamation point (!) indicates that an echo reply was received. A period (.) indicates that an echo reply was not received within the timeout period. An x indicates that an echo reply was received with an error code these packets are not counted in the received packets count. They are accounted for separately.

Sample Output

ping mpls l3vpn

user@host> ping mpls l3vpn vpn1 prefix 10.255.245.122/32

ping mpls l3vpn detail

user@host> ping mpls l3vpn vpn1 prefix 10.255.245.122/32 detail