Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation  Back up to About Overview 
  
[+] Expand All
[-] Collapse All

Resolved Issues

This section lists the issues fixed in the Junos OS main release and the maintenance releases.

For the most complete and latest information about known Junos OS defects, use the Juniper Networks online Junos Problem Report Search application.

Resolved Issues: 15.1F2

Class of Service (CoS)

  • In SNMP environment, when performing multiple walks or parallel snmpget for same interface at the same time (for example, SNMP bulk get/walk, or SNMP polling from multiple devices) on CoS related MIBs (jnxCos table), if the interface state changes or the request gets timeout when FPC is responding the request, memory leak of Class-of-Service process (cosd) about 160 bytes (up to 1500 bytes) may occur, which may cause cosd to crash eventually when limit is exceeded. PR1058915
  • On MX Series platform configured for IP network-services (default) and with MS-DPC/Tunnel-Interface, virtual-tunnel (vt) interfaces are created automatically to support ultimate-hop-popping upon enabling "protocol rsvp". These interfaces are associated with default IP and MPLS classifiers along with MPLS re-write rule. When "protocol rsvp" is disabled/enabled or MS-DPC/FPC (with tunnel-service) restarts, the vt interfaces are deleted and re-added to the system. However during the deletion, these interfaces are not getting released from cosd process and thus leads to memory leak in cosd. PR1071349

General Routing

  • On MX104 router with SONET/SDH OC3/STM1 (Multi-Rate) MIC. In rare condition, if the MIC is plugged out from MX104, the Packet Forwarding Engine might crash, and the traffic forwarding will be affected. These MICs belong to SONET/SDH OC3/STM1 (Multi-Rate) MIC: * MIC-3D-8OC3OC12-4OC48 * MIC-3D-4OC3OC12-1OC48 * MIC-3D-8CHOC3-4CHOC12 * MIC-3D-4CHOC3-2CHOC12 * MIC-3D-8DS3-E3 * MIC-3D-8CHDS3-E3-B * MIC-3D-1OC192-XFP PR997821
  • On MX Series platform with MS-MPC/MS-MIC, if the "dump-on-flow-control" configuration statement is configured, traffic loss and the mspmand process crash might be observed when the MS-PIC comes up with traffic. PR1037086
  • If default-address-selection configuration statement is configured on MX-VC, VC-heartbeat connection between member chassis may be unable to come up. PR1041194
  • Queue stats on LSQ interfaces are not properly cleaned up when queuing is enabled on the IFD and the queues hosted at IFD level. This happens when there is a subsequent delete and create of LSQ interface (not always though). PR1044340
  • On MX Series-based platform, when the feature flow-control is disabled (enabled by default) by using CLI command "no-flow-control" configuration statement (for example, under "gigether-options" hierarchy), after bringing up or rebooting the MPC, due to the fact that status of the hardware may not be updated correctly, the flow control on that MAC may remain enabled. PR1045052
  • In subscriber management environment, the Berkeley Database (DB) may get into deadlock state. It is brought on by multiple daemons attempting to simultaneously access or update the same subscriber or service record. In this case, because the access to DB was blocked by device control daemon (dcd), the subscriber management infrastructure daemon (smid) fails to recover the DB. Consequently, the router may stop responding to all the login/logout requests as well as statistics activity. This timing-related issue is most likely to occur during login or logout and when the system is busy. PR1054292
  • On MX Series routers, the interrupt-driven basis link down detection (an interrupt-driven link-down notification is generated to trigger locally attached systems to declare the interface down within a few milliseconds of failure) may fail after performing a unified in-service software upgrade (ISSU). The interrupt might have been prevented after performing unified ISSU because the interrupt registers were disabled before unified ISSU but never restored afterwards. PR1059098
  • In an IPsec load-balancing environment using MS-MPC cards, the ICMP request and ICMP reply can go through two different IPsec tunnels due to asymmetric routing; that is, ICMP request goes through one PIC, and ICMP reply goes through another PIC. Because of this, the ICMP reply will get dropped and never reach the other side of the IPsec tunnel. PR1059940
  • Due to incomplete fix, in releases containing PR869773 fix, rate limit drops are seen for Ingress queuing even though rate-limit is not configured or supported for ingress. PR1061256
  • On MX Series router with MPC2E-3D-NG/MPC3E-3D-NG/MPC5/MPC6 linecards, the Ethernet frame loss measurement (ETH-LM) feature does not work. PR1064994
  • When a route points to an aggregated multiservices (AMS) logical interface, then after manually bouncing this logical interface by disabling and then enabling it again, aggregate next hop referred by that route will have child unicast next hop pointing to .discard.0 interface instead of member interface (mams) . As a result, traffic ingress on MPC card and routed to that route will be discarded. PR1065944
  • If there are application-sets matching conditions in the NAT rule, NAT port might leak after deleting applications under application-set in live network. PR1069642
  • With basic NAT44, when the router receiving packets on GRE tunnel, NAT was dropping all protocols other than PPTP on GRE tunnel. PR1069872
  • Higher baseline CPU utilization and periodic CPU spikes might be seen on XM-based MPC as compared to MPC-3D-16XGE-SFPP cards due to the following reasons: On XM-based MPC, low priority threads which monitor various things in the background on a periodic basis such as voltage, temperature, stats counters, hardware status and so on are existed. When the system is idle, these threads are allowed to take more of the load, and that is why higher baseline CPU/CPU spikes are seen. This does not prevent other higher priority threads from running when they have to, as these are non-critical activities being done in the background and hence is a non impacting issue. PR1071408
  • overhead-accounting frame-mode command does not work on 100GbE CFP MIC, 100GbE CXP MIC, 2x40GbE QSFP MIC, and 10x10GbE SFPP MIC on MPC3E-3D-NG-Q, MPC3E-3D-NG, MPC2E-3D-NG-Q, and MPC2E-3D-NG PR1072001
  • This may be a false log message - the risk of false log is minor; however, the underlying error, for example, continuous fi recorder timeout, may impact traffic and can be major. When the specific log message is observed in the message file, please advise customer to investigate if there are continuous fabric errors, such as late cell, cell timeout and so on, on the reporting line card and recover those errors first. PR1081771
  • MACsec using static secure association key (SAK) security mode does not work properly on MX80 routers and FPC slots other than slot 0 of MX104 routers. PR1086117
  • On MX Series based line card, if a rlsq interface is receiving continuous fragmented traffic, doing rlsq switchovers couple of times might cause FPC to crash and reboot. PR1088300
  • Some of the new revisions (for example, REV 30, REV 31) of the MICs cannot come up with NG-MPC2 or NG-MPC3 line card. We can check the MIC version by CLI command "show chassis hardware detail | no-more". root@user> show chassis hardware detail | no-more Hardware inventory: Item Version Part number Serial number Description .. FPC 2 REV 14 750-054901 CADJ3871 MPC3E NG PQ & Flex Q CPU REV 11 711-045719 CADN5465 RMPC PMB MIC 0 REV 30 750-028392 CAEB9203 3D 20x 1GE(LAN) SFP Fan Tray 0 REV 05 740-014971 TP5127 Fan Tray Fan Tray 1 REV 05 740-014971 TP5103 Fan Tray. PR1100073
  • Non-queuing MPC5E might crash continuously if rate-limit under transmit-rate for scheduler is applied. As a workaround, do not configure rate-limit and use firewall policer for forwarding-class instead. MPC5EQ is not exposed. PR1104495

Infrastructure

  • A reboot is needed if "chassis network services enhanced-ip" is configured on MX Series Universal Edge 3D Routers or on T4000 Routers with type 5 FPCs. Without the reboot, performing unified ISSU might cause the new master Routing Engine to crash and go to the db> prompt. PR1013262
  • The issue was the gstatd for 64 bit was not getting to the correct path in the code and due to that gstat process was failing to start PR1074084

Interfaces and Chassis

  • On dual Routing Engines platforms, as a High Availability (HA) method, master Routing Engine should relinquish mastership when both Routing Engine-to-Packet Forwarding Engine and Routing Engine-to-other-Routing Engine interfaces are down (this can be achieved only when GRES is enabled). But now on dual Routing Engines platforms except M10i and M20, master Routing Engine does not relinquish the mastership in such conditions, even executing CLI "request chassis routing-engine master acquire" on backup Routing Engine can not help. In such conditions, no FPC can be online without the connection to master Routing Engine. With the fix, the backup Routing Engine will take up the mastership automatically if both the internal link interfaces are down. PR878227
  • On Ethernet PICs with longer hold down timer configured, flapping interface within the hold time might cause traffic loss longer than the hold period. PR1040229
  • When configuring the Virtual Router Redundancy Protocol (VRRP) on an interface which is included in a routing-instance via applying groups setting, if changes are made to the interface, the VRRP process (vrrpd) memory leak might be observed on the device. PR1049007
  • In Virtual Router Redundancy Protocol (VRRP) environment, after restarting the FPC, due to the Router Advertisement (RA) deletion is being incorrectly sent to routing protocol process (rpd) by VRRP process, the ICMPv6 may not be activated on the corresponding interfaces on the router that is acting as the master. In this case, no RA message could be sent out. PR1051227
  • The "show chassis network-services" command might not show the correct configured value when executed on the backup Routing Engine. This command should only be executed on the master Routing Engine. PR1054915
  • On DPC only chassis, after software upgrade or not graceful Routing Engine switchover, Ethernet OAM related LAG bundles might not come up due to the Link Fault Management (LFM) packets arrive on AE interface instead of physical link interface. PR1054922
  • Two redundant logical tunnels (rlt) interfaces are configured with statement "per-unit-mac-disable" enabled. After configuring the second one, the first rlt interface goes down. rlt0 { logical-tunnel-options { per-unit-mac-disable; <<<<<< } } PR1055005
  • The CLI description of the new 100-Gigabit Metro DWDM OTN PIC (PTX-2-100G-WDM-M) is different from the existing 100-Gigabit DWDM OTN PIC (P1-PTX-2-100G-WDM). The 100-Gigabit Metro DWDM OTN PIC's transceiver is identified as OTN-100G-M in the output from the show chassis hardware CLI command and the cable type is identified as 100G METRO in the output from the show chassis pic CLI command. PR1055325
  • There is a mismatch in mac statistics, few frames go unaccounted. This is a day-1 issue with the software fetching of mac statistics. The snap and clear bits were set together on pm3393 chip driver software, so it used to happen that even before the copy of stats to shadow registers happened, clear was happening which used to go unaccounted. Now rollover mechanism has been implemented and tested for 2 continuous days and everything is fine. PR1056232
  • When "set chassis lcc 0 offline" is used on SCC and committed, the configuration gets synced on LCC. However when "delete chassis lcc 0 offline" is used on SCC, we need to do commit two times on SCC in order to sync the config on LCC being brought online. PR1058994
  • In multichassis link aggregation groups (MC-LAGs) environment, the MC-LAG peers have the MAC and port information and can forward the traffic appropriately. If a single VLAN on ICL interface is modified to a different VLAN, and then the administrator rolls back the VLAN configuration to the original one, the remote MAC might be stuck in the "Pending" state and not be installed in the bridge MAC-table, which causes the traffic forwarding to be affected. PR1059453
  • When the Maximum Receive Unit (mru) value is not set under group-profile ppp-options hierarchy, a default value (1492) will be used. If mru value is set, the new value will take effect. But if the configured mru value is deleted from the group profile, the mru value remains the configured one and fails to fall back to the default one. PR1059720
  • On MX Series routers, INET MTU (PPP payload MTU, that is IP header plus data excluding any L2 overhead) is being set to lowest MRU of either MX (local device) or peer. This behavior is not inline with ERX behavior, which is set to min(local MTU, peer MRU). This might cause the packet drops in the customer network in the downstream path. PR1061155
  • In connectivity fault management (CFM) environment, if an AE interface is included in MEP interfaces, and if there is another AE interface configured without any child link (even this AE is not participating in OAM), the CFM sessions might not come up after Routing Engine restart or switchover. PR1063962
  • Error message is continuously logged every second after a particular copper-SFP [P/N:740-013111] is plugged into a disabled port on MIC. ***** error message **** mic_sfp_phy_program_phy: ge-*/*/* - Fail to init PHY link mic_periodic_raw: MIC(*/*) - Error in PHY periodic function PQ3_IIC(WR): no target ack on byte 0 (wait spins 2) PQ3_IIC(WR): I/O error (i2c_stat=0xa3, i2c_ctl[1]=0xb0, bus_addr=0x56) mic_i2c_reg_set - write fails with bus 86 reg 29 mic_sfp_phy_write:MIC(*/*) - Failed to write SFP PHY link 0, loc 29 mic_sfp_phy_mdio_sgmii_lnk_op: Failed to write: ifd = 140 ge-*/*/*, phy_addr: 0, phy_reg: 29 ala88e1111_reg_write: Failed (20) to write register: phy_addr 0x0, reg 0x1d Fails in function ala88e1111_link_init PR1066951
  • To ensure that the router or switch is reachable for management purposes while it boots or if the routing protocol process fails to start properly, we can configure a backup router, which is a router that is directly connected to the local router or switch (that is, on the same subnet) through its private management interface (for example, fxp0 or me0). When a backup router running IPv6 and a static route to reach the management network are configured, some invalid IPv6 routes are added to default forwarding-table on the master or the backup Routing Engine. PR1100981

Layer 2 Features

  • BGP peer configured between two routers over lt (logical tunnel) interface, if deactivating and activating scaled configuration a few times, in rare condition, the lt interface might reject all the ARP reply packets, and hence the ARP resolution does not happen over this interface. Thus, the unicast routes are not in the correct states, and ping to such an lt interface will fail. PR1059662
  • LACP partner system ID is shown incorrectly when the AE member link is connected to a different device, which might misguide while troubleshooting the LAG issues. PR1075436
  • The Enhanced LAG feature is enabled in network-service enhanced-ip mode, but it is not supported in enhanced-ethernet mode. PR1087982

MPLS

  • The entropy label value allocated at times falls in the reserved mpls label range(0-15). The label value is calculated based on load balancing information and hence only certain mpls flows may encounter this issue. PR1014263
  • With BGP labeled-unicast egress protection enabled in a Layer 3 VPN, the protected node advertises primary BGP labeled unicast routes that needs protection. When there is next-hop change for a labeled route, for example, deactivating/activating egress-protection configuration statement or route churn, the memory might be exhausted which leads to the rpd process crash. PR1061840
  • When fast-reroute, node-link-protection, or link-protection is configured, if a Shared Risk Link Group (SRLG) is associated with a link used by an LSP ingressing at a router, then on deleting the SRLG configuration from the router, the SRLG entry still stays in the SRLG table even after the re-optimization of this LSP. PR1061988
  • The "load-balance-label-capability" configuration statement is introduced to enable the router to push and pop the load-balancing label, which causes LDP and RSVP to advertise the entropy label TLV to neighboring routers. MX Series, T4000, and PTX Series have the capability and it is reflected in their default forwarding-options configuration. However, there is a software defect in the way that Entropy Label Capability (ELC) TLV is encoded in the LDP label mapping message. It might cause the LDP session between routers to go down. PR1065338
  • When CSPF computes the path for node-protected bypass, it considers only the SRLG group configured on next-hop interface along the primary path. However it doesn't consider the SRLG group on next-to-next-hop interface to adequately provide diverse path between primary and node-protected bypass. PR1068197
  • When a primary LSP gets re-routed due to better metric, Link/Node protection for this LSP is expected to come up within 7 seconds provided the bypass-lsp protecting the next-hop link/node is already available. However in some corner cases, the Link/Node protection for re-routed primary LSP will not come up within 7 seconds even with bypass-lsp availability. The PR fixes this issue and reduces the delay of associating bypass-lsp with primary-lsp from 7 seconds to 2 seconds. PR1072781
  • In MPLS environment, if one of minimum-signaling-bandwidth/merging-bandwidth/splitting-bandwidth/maximum-s ignaling-bandwidth is configured, or derived as value 0, the routing protocol process (rpd) may crash when lsp-splitting or lsp-merging (for example, when the traffic comes up/down) occurs. As a workaround, due to the logic of the configuration statement, none of the following configuration statement could be configured or derived as zero, -merging-bandwidth -minimum-signaling-bandwidth -splitting-bandwidth -maximum-signaling-bandwidth PR1074472

Network Management and Monitoring

  • SNMP queries for LAG MIB tables while LAG child interface is flapping, may cause mib2d grow in size and eventually crash with a core file. Mib2d will restart, and recover by itself. PR1062177
  • The text string of the SNMP object "system.sysDescr.0" does not include the Junos OS version of the device and displays the version of the FreeBSD kernel running on the Routing Engine instead. PR1073232

Platform and Infrastructure

  • Recurring local memory (LMEM) data errors may cause lookup chip on Trio based FPC wedge and eventually FPC crash. PR1033660
  • If several aggregates are configured with shared-bandwidth-policer and those aggregates share the same Packet Forwarding Engine for child member links and one member links flaps, all traffic might get policed and dropped. The traffic dropped might not be on the bundle whose child member link flapped. PR1035845
  • Due to a defect in the Junos OS Software, when a telnet user experiences some undefined network disconnect, .perm and .env files under /var/run are left behind. This scenario happens only under certain unknown ungraceful network disconnects. When considerable number of .perm/.env files get accumulated under /var/run, issue is seen with telnet users, that they are not able to perform permitted operations on the router, post-login. PR1047609
  • For a Routing Matrix, if different Routing Engine models are used on switch-card chassis (SCC)/switch-fabric chassis (SFC) and line-card chassis (LCC) (for example, RE-1600 on SCC/SFC and RE-DUO-C1800 on LCC), where the out-of-band (OoB) management interfaces are named differently (for example, fxp0 on SCC/SFC Routing Engine and em0 on LCC Routing Engine), then the OoB management interface configuration for LCC Routing Engine will not be propagated from SCC/SFC Routing Engine during commit. PR1050743
  • With VLAN manipulation configured for Ethernet Services, incorrect frame length might be used for egress policing on Trio-based line cards. Currently, the frame length calculation is inconsistent for different traffic topology: 1. In case traffic crossed the fabric, the frame length prior to output VLAN manipulation is used; 2. In case of local traffic, the frame length prior to input VLAN manipulation is used. Actually the length after output VLAN manipulation should always be used. PR1064496
  • When performing unified in-service software upgrade (ISSU) on MX Series routers with unsupported MICs (for example, "MIC-3D-8OC3OC12-4OC48") equipped, the MPC might crash during the field-replaceable unit (FRU) upgrade process. For example, unified ISSU is supported only by the MICs listed here on Junos OS release 14.2: MIC-3D-20GE-SFP MIC-3D-2XGE-XFP MIC-3D-4XGE-XFP MIC-3D-40GE-TX MIC-3D-8OC3-2OC12-ATM MIC3-3D-2X40GE-QSFPP MIC3-3D-10XGE-SFPP MIC3-3D-1X100GE-CXP MIC3-3D-1X100GE-CFP. PR1065731
  • Starting from Junos OS Release 14.2R1, the CLI command "set date ntp a.b.c.d" may not be working. PR1067107
  • StartTime and EndTime of the flow in inline-jflow (version 9) has future time-stamp. PR1067107
  • Firewall filters which have a prefix-action can't be configured under [edit logical-system <name> firewall family inet] because the Packet Forwarding Engine won't be programmed for the filter. PR1067482
  • If with about 1M routes on MX Series router, there might be more than 1 second (about 1.3s) packets dark window during unified ISSU. PR1070217
  • VPLS filter applied under forwarding-options might drop VPLS frame unexpectedly when it is coming from an lt- interface. PR1071340
  • If port-mirroring and VRRP over ae-irb is configured in a bridge-domain, enabling the Distributed Periodic Packet Management Process (ppmd) for VRRP in this BD might cause the VRRP to flap. PR1071341
  • When inline-sampling is enabled, in race conditions, if packet gets corrupted and the corrupted packet length shows 0, this may cause "PPE_x Errors thread timeout error" and eventually cause MPC card to crash. PR1072136
  • VRRP advertisements might be dropped after enable delegate-processing on the logical tunnel (lt) interface. It would result in VRRP master state observed on both routers. PR1073090
  • When an MX Series chassis network-services is "enhanced-ip" and an AE with "family bridge" configuration is first committed, there is a possibility that an incorrect forwarding path may be installed causing traffic loss. PR1081999
  • Issue is specific to 64-bit RPD and config-groups wildcard configuration specifically as in the following case: set groups TEST routing-instances <*> routing-options multicast forwarding-cache family inet threshold suppress 200 set routing-instances vrf1 apply-groups TEST set routing-instances vrf1 routing-options multicast forwarding-cache family inet threshold suppress 600 With this daemon(rpd) reads suppressed value “200” (that is, coming from groups) instead of reading value “600” from foreground, and customer sees unexpected behavior with respect to threshold-suppress. Workaround: They can replace wildcard with actual routing-instance name as in the following example: set groups TEST routing-instances vrf1 routing-options multicast forwarding-cache family inet threshold suppress 200 set routing-instances vrf1 apply-groups TEST set routing-instances vrf1 routing-options multicast forwarding-cache family inet threshold suppress 600 PR1089994

Routing Protocols

  • Deletion of a routing-instance may lead to a routing daemon crash. This may happen if the routing-instance Routing Information Base (RIB) is referenced in an active policy-option configuration. As a workaround, when deactivating the routing-instance, all associated configurations using the route-table names in the routing-instance should also be deactivated. PR1057431
  • In PIM environment, Bootstrap Router (BSR) can be used only between PIMv2 enabled devices. When deactivating all the interfaces which are running PIM bootstrap, the system changes to operate in PIMv1. At this time, all the information learned about/from the current BSR should be cleaned, but actually, BSR state is not cleaned. If the interface which was the previous "elected BSR" is activated, BSR state is PIM_BSR_ELECTED(should be cleaned previously) and the system assumes the BSR timer is still here. When the system tries to access the null BSR timer, the rpd process might crash. PR1062133
  • If with a large number of multicast sources for a same multicast group in PIM dense mode, the rpd process might crash after Routing Engine switchover. PR1069805
  • For the pim nbr which is not directly connected ( that is, nbr on unnumbered interface, or p2p interface with different subnet), pim join is not able to find the correct upstream nbr which results in join not propagating to the upstream nbr . show command for pim join shows upstream nbr "unknown" . Issue is present in the 15.1R1 release. PR1069896
  • In Protocol Independent Multicast (PIM) sparse mode environment, if the router is being used as the rendezvous point (RP) and also the last hop router, when the (*,G) entry is present on the RP and a discard multicast route (for example, due to receiving multicast traffic from a non-RPF interface) is already existed, if the (S,G) entry is learned after receiving source-active (SA) of the Multicast Source Discovery Protocol (MSDP), the SPT cutover may fail to be triggered. There is no traffic impact as receivers still can get the traffic due to (*,G) route. PR1073773
  • In multi-topologies IS-IS scenario, there is huge difference between estimated free bytes and actual free bytes when generating LSP with IPv6 prefix. It might cause LSP fragment exhaustion. PR1074891
  • With Multicast Source Discovery Protocol (MSDP) and nonstop active routing (NSR) configured on the Protocol Independent Multicast (PIM) sparse-mode rendezvous point (RP), the rpd process might permanently get stuck when multicast traffic received shortly after Routing Engines switchover. PR1083385
  • 1. Configure the ospf and ospf3 in all routers 2. Configure node protection 3. Check for 22.1.1.0 any backup is present 4. Enable pplfa all 5. Check for 22.1.1.0 any pplfa backup is present through r2. We are not seeing any pplfa backup for 22.1.1.0. PR1085029

Services Applications

  • The session-limit-per-prefix feature for the MX Series DS-Lite server does not take Softwire flow into account when calculating the flow limit. PR1023439
  • On M Series, MX Series, T Series routers with Multiservices 100, Multiservices 400, or Multiservices 500 PICs with "dump-on-flow-control" configured, if prolonged flow control failure, the coredump file might generate failure. PR1039340
  • On MX Series routers that are acting as LNS to provide tunnel endpoints, it is observed that the service-interfaces are not usable if a MIC corresponding to them is not physically installed on the FPC. If only those service interfaces that belong to the removed PIC are added to service-device-pool, this results in no LNS subscribers being able to log in. Note that once the MIC is inserted into the FPC, the features could be used. PR1063024
  • When configuring RADIUS authentication for Layer 2 Tunneling Protocol (L2TP), the RADIUS server cannot be recognized because the source address is not being read correctly. As a result, the L2TP session cannot be established. PR1064817
  • The trigger for the crash is when the MS-DPCs Service PIC is in a low memory zone and it receives two SYN messages from the the same client IP within a very short time gap in between the two SYNs. So this race condition is tied to running out of memory, failing to allocating a timer for a conversation, and having rapid SYNs on a TCP connection where the second TCP SYN is matched on flow which is being deleted due to a failed timer allocation for that. This scenario is very difficult to hit and should not be seen in production often. PR1069006
  • Service PIC daemon (spd) might crash with core-dumps due to CGNAT pool's snmp-trap-thresholds configuration. PR1070370
  • Earlier output from "show service l2tp tunnel" will not display tunnels with no sessions. This behavior have been changed, now empty tunnels are also displayed in this command. PR1071923

Software Installation and Upgrade

  • Add "on <host>" argument to "request system software validate" to allow validation on a remote host/Routing Engine running Junos OS. PR1066150

User Interface and Configuration

  • Due to a change in an existing PR, group names in the configuration must be a string of alphanumericals, dashes, or underscores. There is no workaround other than following the group name instructions. PR1087051

VPNs

  • In the l2circuit environment, when l2ckt configuration has backup-neighbor, the flow-label operation is blocked at the configuration level. PR1056777
  • On dual Routing Engines, if mvpn protocol itself is not configured, and nonstop active routing is enabled, the show command "show task replication" on the master Routing Engine will list the MVPN protocol even though it is not configured. Other than the misleading show output which may be slightly confusing to the user/customer, there is no functional impact due to this issue as such. There is no workaround available. PR1078305

Related Documentation

Modified: 2017-07-06