Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Creating a Point-to-Point Ethernet Service Definition

 

Use this procedure to create a definition for a point-to-point VPN service. The standard service definitions that came with your initial software installation are designed to be appropriate for most requirements. You can also create a customized service definition—for example, to set different bandwidth limits on the service than those offered in the standard service definitions.

After the new service definition is complete and published, network operators or service provisioners can use the completed service definition as a base for creating and then activating point-to-point VPN services on the network.

The pages appear in the order stated. You can, however, perform these steps in any order by accessing them through the task list in the right panel. If the panel is not visible, click the snap tool on the right side of the main display area.

To create a point-to-point service definition, complete these tasks, in the order shown:

Specifying General Information

To specify the general information for a point-to-point Ethernet service definition:

  1. In the Network Activate task pane, select Service Design > Manage Service Definitions > Create P2P Service Definition. The General settings page appears.
  2. Fill in the fields in the General page.

    Field

    Action

    Name

    Enter a name for the service definition.

    Service type

    By default, the service type is Point-to-Point Pseudowire.

    Signaling

    Select a signaling type:

    • BGP

    • LDP

    You cannot edit the Signaling type in the service order.

    Note: If the signaling type is BGP, the Static pseudowire and the Enable PW access to L3 VPN network check boxes are not available. You cannot edit the Signaling type in the service order.

    Comments (Optional)

    Enter a brief description or other comment that you want to appear in the Service Definition table.

    Range: 0 through 200 characters. Spaces and special characters are allowed.

    Enable QoS

    When you enable QoS in the service definition, you must specify a QoS profile in the service order to classify traffic into defined service groups to provide the special treatment of traffic across the network service. For example, voice traffic can be sent across certain links, and data traffic can use other links.

    Interface type

    Select the interface type:

    • Ethernet

    • TDM

    • ATM

    Static pseudowire

    To enable static pseudowire, select the Static pseudowire check box. This check box is disabled if the signaling type is BGP.

    Enable PW access to L3 VPN network

    To enable the pseudowire access to L3 VPN network, select the Enable PW access to L3 VPN network check box. This check box is disabled if the signaling type is BGP, or if you have selected the interface type as TDM/ATM.

    If you select this check box, the Enable Multi Segment Pseudowire check box is disabled.

    Enable Multi Segment Pseudowire

    Select this check box to enable multi-segment pseudowire.

    If you select this check box, the Enable PW access to L3 VPN network check box is disabled.

    A multi-segment pseudowire (MS-PW) is a static or dynamically configured set of two or more contiguous pseudowire segments that behave and function as a single point-to-point pseudowire. Each end of an MS-PW, by definition, terminates on a T-PE.

    Note: The number of pseudowire segments that you can stitch is limited to two.

    For more information on point-to-point pseudowire stitching, see Stitching Two Point-to-Point Pseudowires.

    Enable PW Resiliency

    To enable the pseudowire resiliency, select the Enable PW Resiliency check box. For more information on pseudowire redundancy, see Redundant Pseudowires for Layer 2 Circuits and VPLS.

    Decouple Service Status From Port Status

    By default, all the events are saved in the OpenNMS database. To isolate the events related to an interface in the OpenNMS, select the Decouple Service Status From Port Status check box.

    Note: When you select this check box, only the pseudowire traps are monitored, not the jnxVpnIfVpn traps.

    Service Template

    (Optional) To include a service template for the service, select a service template from the Service Template list.

    The selected service template appears in the Default Service Template field.

    You can select one or more service templates as the default service template. By default, the default service templates are attached to the endpoints.

    Note: You cannot add or delete a service template while creating a service order.

    The remaining service templates on the Service Template list are termed as optional service templates. You can attach the optional service templates to the endpoints on a need basis.

    In the View Service Definition Details page, the value for the default service template in the Default Service Template column is True.

    For instructions on creating a service template, see Creating a Service Template.

    Threshold alarm profile

    If you intend to run performance tests on services based on this service definition, select a TCA Profile.

  3. Click Next to save the information. Continue with Specifying UNI Settings.

Specifying UNI Settings

In this step, you provide the UNI service attributes for this service definition. The attributes you set depend on whether you are setting attributes for a port, an 802.1Q interface, a Q-in-Q interface, or a flexible VLAN tagging:

Specifying UNI Settings for Port-to-Port Services

To set UNI attributes for a port-to-port service, complete the following procedure.

  1. Enter information in the UNI Settings page.
  2. Fill in the fields in the UNI Settings page according to the following table.

    Field

    Action

    Traffic Treatment Settings

    Ethernet option

    Select port-port from the list.

    The Ethernet option you choose determines the other options you can select and specify on the page.

    Customer traffic type

    Select N/A. For port-to-port services, all traffic is always transported.

    VLAN ID selection

    In port-to-port services, all traffic and all VLANs on one port are transported to all other ports.

    Editable in Service Order

    Select this check box to allow the service provisioner to override the MTU setting.

    Interface Settings

    Physical IF encapsulation

    Select ethernet-vpls, the only valid physical interface encapsulation method allowed for port-to-port services.

    Logical IF encapsulation

    You cannot change this field because it is not relevant to port-to-port services.

    MTU Settings

    Default MTU (Bytes)

    You can specify an MTU value in this field. The default value for MTU is 1522 bytes.

    To see the permitted range for the MTU value, select the Editable in Service Order check box. The MTU range is 1522 through 9192.

    MTU Range (Bytes)

    If you select the check box Editable in Service Order, you can specify a value range for MTU (in bytes). The permitted range for MTU is 1522 through 9192.

    Note: Ultimately, the system establishes the MTU by multiplying the value you specify in the Default MTU (Bytes) field by the value you specify for MTU Factor.

    Calculation of Burst-Size

    Calculate Burst Size

    Select the preferred option for calculating the burst size:

    • MTU Based

      If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

      The default value for MTU Factor is 1.

    • Line Rate Based

      If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

      The default value for Burst Period is 1.

    Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

    The following illustration shows the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

    Bandwidth Settings

    The following illustration shows the Bandwidth Settings panel, which appears if you do not select the Enable QoS check box in the preceding General settings page.

    Enable rate limiting (check box)

    If you select this check box, you can override the MTU setting.

    Default bandwidth (Mbps)

    Specify the default bandwidth value, in Mbps.

    Default: 10 Mbps

    Range: 1 Mbps through 100,000 Mbps

    Min Bandwidth (Kbps)

    To override the default bandwidth value, select the Editable in Service Order check box.

    Specify the minimum bandwidth value in Kbps:

    Default: 1000 Kbps

    Range: 64 Kbps through 100,000 Kbps

    Max Bandwidth (Mbps)

    Specify the maximum bandwidth value, in Mbps.

    Default: 100 Mbps

    Range: 1 Mbps through 100,000 Mbps

    The following table lists the Max Bandwidth (Mbps) for the M Series, MX Series, and ACX Series Routers:

    Table 1: Maximum Bandwidth for M Series, MX Series, and ACX Series Routers

    M Series IQ2E PIC

    M Series IQ2 PIC

    MX Series 3D PIC

    MX Series Non-3D PIC

    ACX 2000

    GE Port (1G)

    XE Port (10G)

    GE Port (1G)

    XE Port (10G)

    GE Port (1G)

    XE Port (10G)

    GE Port (1G)

    XE Port (10G)

    GE Port (1G)

    XE Port (10G)

    32,000 Mbps or 32 Gbps

    32,000 Mbps or 32 Gbps

    50,000 Kbps or 50 Gbps

    50,000 Kbps or 50 Gbps

    100,000 Mbps or 100 Gbps

    100,000 Mbps or 100 Gbps

    50,000 Kbps or 50 Gbps

    50,000 Kbps or 50 Gbps

    50,000 Kbps or 50 Gbps

    50,000 Kbps or 50 Gbps

    Increment (Kbps)

    Specify a value in the range that is made available to the service provisioner.

  3. Click Next to continue with Connectivity settings.

Specifying UNI Settings for Services with 802.1Q Interface Types

To set UNI attributes for 802.1Q interfaces complete the following procedure.

  1. Enter information in the UNI Settings page.
  2. Fill in the fields in the UNI Settings page according to the following table:

    Field

    Action

    Traffic Treatment Settings

    Ethernet option

    Select dot1q from the list.

    The Ethernet option you choose determines the other options you can select and specify on the page.

    Customer traffic type

    Single VLAN is the only option for 802.1Q interface types.

    Select Transport single vlan to transport the traffic for a specific VLAN across the network. When you select this option, the service provisioner is prompted for the VLAN-ID when creating a service order based on this service definition. You need to specify the Outer Tag protocol ID.

    Select Transport VLAN range to limit the traffic across the network to a specific range of VLANs.

    If you select this option, the service provisioner is prompted for the VLAN-ID range when creating a service order based on this service definition.

    Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

    VLAN ID selection

    Indicate how the VLAN ID is determined:

    • Select manually—Allows the service provider to specify the VLAN ID. This option is normally used when no VLAN normalization is applied. Specify the VLAN ID range in VLAN range for manual input.

      Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

    • Auto pick—This option is normally used when VLAN normalization is applied. Specify the VLAN ID pool in VLAN range for auto-pick.

      Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

    VLAN range for auto-pick

    Specify the VLAN ID pool.

    Range: 1 through 4094

    VLAN range for manual input

    Specify the VLAN ID range.

    Range: 1 through 4094

    Outer Tag protocol ID

    Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN:

    • 0x88a8

    • 0x8100

    • 0x9100

    Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPIDs) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands:

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100

    Editable in Service Order

    To allow the service provisioner to override the MTU setting, select the check box for those options.

    Interface Settings

    Physical IF encapsulation

    Select the default physical encapsulation scheme to be used by service orders based on this service definition. We recommend you select flexible-ethernet-services.

    Logical IF encapsulation

    Constrained by your selection in the Physical IF encapsulation box. If you selected the recommended physical encapsulation mode of flexible-ethernet-services, then your only option is to select vlan-vpls for the logical encapsulation method.

    MTU Settings

    Default MTU (Bytes)

    You can specify an MTU value in this field. The default value for MTU is 1522.

    To see the permitted range for the MTU value, select the Editable in Service Order check box. The MTU range is 1522 through 9192.

    MTU Range (Bytes)

    If you select the check box Editable in Service Order, you can specify a value range for MTU (in bytes). The permitted range for MTU is 1522 through 9192.

    Note: Ultimately, the system establishes the MTU by multiplying the value you specify in the Default MTU (Bytes) field by the value you specify for MTU Factor.

    Calculation of Burst-Size

    Specify the default bandwidth value, in Mbps.

    Default: 10 Mbps

    Range: 1 Mbps through 100,000 Mbps

    Calculate Burst Size

    Select the preferred option for calculating the burst size:

    • MTU Based

      If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

      The default value for MTU Factor is 1.

    • Line Rate Based

      If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

      The default value for Burst Period is 1.

    Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

    The following illustration shows the appearance of the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

  3. Click Next to continue with connectivity settings.

Specifying UNI Settings for Services with Q-in-Q Interface Types

To set UNI attributes for a Q-in-Q service, complete the following procedure.

  1. To set UNI attributes for Q-in-Q interfaces:
  2. Fill in the fields in the UNI Settings page according to the following table:

    Field

    Action

    Traffic Treatment Settings

    Ethernet option

    Select qinq from the list.

    The page expands to include options specific to Q-in-Q interfaces.

    Customer traffic type

    Specify the customer traffic type:

    • Transport all traffic—Transports the traffic from all VLANs across the network. When you select this option, the service provisioner is prompted for the VLAN-ID when creating a service order based on this service definition. You need to specify only the Outer Tag protocol ID.

    • Transport single vlan—Transports traffic for a specific VLAN across the network. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID.

    • Transport VLAN range—Limits the traffic across the network to a specific range of VLANs.

      If you select this option, the service provisioner is prompted for the VLAN-ID range when creating a service order based on this service definition. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID.

    Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

    VLAN ID selection

    Indicate how the VLAN ID is selected during service order creation.

    • Select manually—Allows the service provider to specify the VLAN ID. This option is normally used when no VLAN normalization is applied.

      Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting. Specify the VLAN ID range in VLAN range for manual input.

    • Auto pick—This option is normally used when VLAN normalization is applied. Specify the VLAN ID pool in VLAN range for auto-pick.

      Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

    VLAN range for auto-pick:

    Specify the VLAN ID pool.

    Range: 1 through 4094

    VLAN range for manual input

    Specify the VLAN ID range.

    Range: 1 through 4094

    Outer Tag protocol ID

    Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN:

    • 0x88a8

    • 0x8100

    • 0x9100

    Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPIDs) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands:

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100

    Inner Tag protocol ID

    Select the inner tag protocol ID:

    • 0x88a8

    • 0x8100

    • 0x9100

    Note: You cannot specify the Inner Tag protocol ID if the Customer traffic type is Transport single VLAN.

    Editable in Service Order

    Select this check box to allow the service provisioner to override the MTU setting.

    Interface Settings

    Physical IF encapsulation

    Select the default physical encapsulation scheme to be used by service orders based on this service definition. We recommend you select flexible-ethernet-services.

    Logical IF encapsulation

    Constrained by your selection in the Physical IF encapsulation box. If you selected the recommended physical encapsulation mode of flexible-ethernet-services, then your only option is to select vlan-vpls for the logical encapsulation method.

    MTU Settings

    Default MTU (Bytes)

    You can specify an MTU value in this field. The default value for MTU is 1522.

    To see the permitted range for the MTU value, select the Editable in Service Order check box. The MTU range is 1522 through 9192.

    MTU Range (Bytes)

    If you select the check box Editable in Service Order, you can specify a value range for MTU (in bytes). The permitted range for MTU is 1522 through 9192.

    Note: Ultimately, the system establishes the MTU by multiplying the value you specify in the Default MTU (Bytes) field by the value you specify for MTU Factor.

    Calculation of Burst-Size

    Calculate Burst Size

    Select the preferred option for calculating the burst size:

    • MTU Based

      If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

      The default value for MTU Factor is 1.

    • Line Rate Based

      If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

      The default value for Burst Period is 1.

    Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

    The following illustration shows the appearance of the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

  3. Click Next to continue with Connectivity settings.

UNI Settings for Services with Flexible VLAN Tagging (Asymmetric Interface Types)

You can specify the Ethernet option asymmetric tag depth to create a service that includes any combination of port-based interfaces, 802.1Q interfaces, and Q-in-Q interfaces.

  1. Enter information in the UNI Settings page.
  2. Specify the UNI Settings for asymmetric tag depth according to the following table:

    Field

    Action

    Traffic Treatment Settings

    Ethernet option

    Select asymmetric tag depth from the list.

    Customer traffic type

    Select the customer traffic type:

    • Transport all traffic—Transports the traffic from all VLANs across the network. When you select this option, the service provisioner is prompted for the VLAN-ID when creating a service order based on this service definition. You need to specify only the Outer Tag protocol ID and Inner Tag protocol ID.

    • Transport single vlan—Transports traffic for a specific VLAN across the network. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID.

    • Transport VLAN range—Limits the traffic across the network to a specific range of VLANs. You need to specify both Outer Tag protocol ID and Inner Tag protocol ID.

      If you select this option, the service provisioner is prompted for the VLAN-ID range when creating a service order based on this service definition.

    Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

    VLAN ID selection

    Indicate how the VLAN ID is selected during service order creation.

    • Select manually—Allows the service provider to specify the VLAN ID. This option is normally used when no VLAN normalization is applied. Specify the VLAN ID range in VLAN range for manual input.

      Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

    • Auto pick—This option is normally used when VLAN normalization is applied. Specify the VLAN ID pool in VLAN range for auto-pick.

      Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting. Specify the VLAN ID pool in VLAN range for auto-pick.

    VLAN range for auto-pick:

    Specify the VLAN ID pool.

    Range: 1 through 4094

    VLAN range for manual input

    Specify the VLAN ID range.

    Range: 1 through 4094

    Outer Tag protocol ID

    Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN:

    • 0x88a8

    • 0x8100

    • 0x9100

    Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPIDs) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands:

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8

    set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100

    Inner Tag protocol ID

    Select the inner tag protocol ID:

    • 0x88a8

    • 0x8100

    • 0x9100

    Note: You cannot specify the Inner Tag protocol ID if the Customer traffic type is Transport all traffic.

    Editable in Service Order

    To allow the service provisioner to override the MTU setting, select the check box for those options.

    Interface Settings

    Physical IF encapsulation

    Select the default physical encapsulation scheme to be used by service orders based on this service definition. We recommend you select flexible-ethernet-services.

    Logical IF encapsulation

    Constrained by your selection in the Physical IF encapsulation box. If you selected the recommended physical encapsulation mode of flexible-ethernet-services, then your only option is to select vlan-vpls for the logical encapsulation method.

    MTU Settings

    Default MTU (Bytes)

    You can specify an MTU value in this field. The default value for MTU is 1522.

    To see the permitted range for the MTU value, select the Editable in Service Order check box. The MTU range is 1522 through 9192.

    MTU Range (Bytes)

    If you select the check box Editable in Service Order, you can specify a value range for MTU (in bytes). The permitted range for MTU is 1522 through 9192.

    Note: Ultimately, the system establishes the MTU by multiplying the value you specify in the Default MTU (Bytes) field by the value you specify for MTU Factor.

    Calculation of Burst-Size

    Calculate Burst Size

    Select the preferred option for calculating the burst size:

    • MTU Based

      If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

      The default value for MTU Factor is 1.

    • Line Rate Based

      If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

      The default value for Burst Period is 1.

    Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

    The following illustration shows the appearance of the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

  3. Click Next to continue with Connectivity settings.

Specifying Connectivity Information When Signaling Is LDP

The fields displayed in the Connectivity page depend on the Signaling type (LDP or BGP) that you selected in the General settings page.

To specify connectivity between sites across the network when signaling is LDP:

  1. Fill in the fields in the Connectivity page.

    Field

    Action

    VC ID selection

    The VC ID selection is available only if the Signaling type is LDP.

    In the VC ID selection box, specify how you want the VC ID to be chosen during service order creation:

    • To allow the service provisioner to enter the VC ID, choose Select manually.

    • To cause the Junos Space software to assign a VC ID automatically from the VC ID pool, select Auto pick.

    To allow the service provisioner to override the setting in the VC ID box, select Editable in Service Order.

    Default MTU

    In the Default MTU box, specify the MTU across the service provider network.

    To allow the service provisioner to override the MTU setting, select Editable in Service Order. In the MTU range, enter the highest and lowest MTU that the service provisioner can enter.

    Revert time (sec)

    This field is available if you selected the Enable PW Resiliency check box and if the Signaling is LDP in the General settings.

    Revert time (sec)—Revert time for redundant Layer 2 circuits and VPLS pseudowires.

    Default: 5 seconds

    Range: 0 through 65,535 seconds

    Switch Over Delay (sec)

    This field is available if you selected the Enable PW Resiliency check box and if the Signaling is LDP, in the General settings.

    Switch Over Delay (sec)—Delay to wait before the backup pseudowire takes over.

    Default: 0 second

    Range: 0 through 180 seconds

    VLAN Normalization

    The options available in the VLAN normalization are based on the value set for the Ethernet interface.

    Outgoing label selection

    This field is available if you selected the Static pseudowire check box in the General settings. By default, the outgoing label selection is limited to manual.

    The following table presents the available VLAN normalization options:

    Ethernet Option

    Customer Traffic Type

    VLAN Normalization

    port-port

    N/A

    Normalization not required

    Normalization to Dot1q tag

    Normalization to QinQ tags

    dot1q

    Transport single vlan

    Swap

    Normalize to None

    Normalization to Dot1q tag

    Normalization to QinQ tags

     

    Transport vlan range

    Normalization not required

    qinq

    Transport all traffic

    Swap

    Normalize to None

    Normalization to Dot1q tag

    Normalization to QinQ tags

     

    Transport single vlan

    Swap

    Normalize to None

    Normalization to Dot1q tag

    Normalization to QinQ tags

     

    Transport vlan range

    Normalization not required

    Asymmetric

    (Identical to qinq)

    (Identical to qinq)

  2. Click Finish to complete the service definition.

Specifying Connectivity Information When Signaling Is BGP

To specify connectivity between sites across the network when signaling is BGP, fill in the fields in the Connectivity page:

  1. When the signaling type is BGP, fill in the fields in the Connectivity page.
    • Route Distinguisher—Identifier attached to a route, enabling you to distinguish to which VPN the route belongs. Each routing instance must have a unique route distinguisher associated with it.

      Note

      The IPv4 and IPv6 addresses that you use must be valid addresses. Refer to http://www.iana.org/assignments/ipv4-address-space for the list of restricted IPv4 addresses and http://www.iana.org/assignments/ipv6-address-space for the list of restricted IPv6 addresses.

    • Route Target—Allows you to distribute VPN routes to only the routers that need them.

      Note

      The IPv4 and IPv6 addresses that you use must be valid addresses. Refer to http://www.iana.org/assignments/ipv4-address-space for the list of restricted IPv4 addresses and http://www.iana.org/assignments/ipv6-address-space for the list of restricted IPv6 addresses.

    • Default MTU (Bytes)—The default MTU established by the system.

    • MTU range (Bytes)—Specify the range, in bytes, for the MTU.

    • VLAN normalization—The options available in the VLAN normalization field are based on the value set for the Ethernet interface. The following table presents the options.

      Ethernet Option

      Customer Traffic Type

      VLAN Normalization

      port-port

      N/A

      Normalization not required

      Normalization to Dot1q tag

      Normalization to QinQ tags

      dot1q

      Transport single vlan

      Swap

      Normalize to None

      Normalization to Dot1q tag

      Normalization to QinQ tags

       

      Transport vlan range

      Normalization not required

      qinq

      Transport all traffic

      Swap

      Normalize to None

      Normalization to Dot1q tag

      Normalization to QinQ tags

       

      Transport single vlan

      Swap

      Normalize to None

      Normalization to Dot1q tag

      Normalization to QinQ tags

       

      Transport vlan range

      Normalization not required

      Asymmetric

      (Identical to qinq)

      (Identical to qinq)

      Note

      For a description of how the Network Activate software manipulates VLANs, see Understanding VLAN Manipulation (Normalization and VLAN Mapping) on Ethernet Services.

  2. Click Finish to complete the service definition.