Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

Creating a Service Definition for VPLS Access into Layer 3 Networks

 

You can configure an Integrated Routing and Bridging (IRB) interface to provide access from VPLS Layer 2 networks and services into Layer 3 networks. If the IRB interface configured as a Layer 3 interface is being used in a routing instance, that routing instance will specifically declare it as routing-interface rather than a regular VPLS interface (which acts like the interface on a specific VPLS site). This feature requires a normalized VLAN (vlan-id=xxx which is the same as the unit name on which the inet4 address is specified)

Junos Space uses the two peer subinterfaces of the IRB to create the link between an existing VLAN and the Layer 3 network. An extra VPLS node is required to support the IRB interface which allows the rest of the VPLS nodes to be able to access all Layer 3 networks reachable through that interface. Providing the VPLS access into Layer 3 networks enhances basic VPLS services. Because this feature requires a normalized VLAN, it is available only on the Juniper Networks MX 3D Router series.

Prerequisites for VPLS Access into Layer 3 Networks

  • The PE device with the IRB must be a Juniper Networks MX 3D Series Router to accommodate the normalized VLAN requirement.

  • In addition to the PE device used for the IRB, 2 or more PEs must exist on the VPLS network for a minimum of 3 PE devices.

  • A VLAN must already exist to configure this feature.

To begin the configuration of the IRB interface, in the Network Activate task pane, select Service Design > Manage Service Definitions > Create VPLS Service Definition.

Field

Action

Name

Provide a name for the VPLS service definition you want to create.

Service Type

Select the type of service from the menu list. To create the VPLS into Layer 3 service, use either of the following service type:

  • Multipoint-to-Multipoint Ethernet (VPLS)

  • Point-to-Multipoint Ethernet (VPLS)

Comments

Provide any comments or a description that will help explain the purpose of this definition.

Enable L3 Access

Check the box to create the link into Layer 3.

  1. Click Next to display the next page, UNI Settings, and continue creating the service definition.

Specifying UNI Settings

UNI Settings Field

Action

Traffic Treatment Settings

Ethernet option

Indicate the Ethernet option to use for this VPLS service definition. Choices are qinq or dot1q.

Customer traffic type

The only option for VPLS service definitions is Transport single VLAN.

VLAN ID selection

The only option for VPLS service definitions is Select manually.

Interface Settings

Physical IF encapsulation

The only option for VPLS service definitions is flexible-ethernet-services

Logical IF encapsulation

The only option for VPLS service definitions is vlan-vpls.

MTU Settings

Default MTU (Bytes)

This field is populated with the default MTU value of 1522. If you are not using the default value, enter the MTU value in bytes.

MTU range (Bytes)

If you are specifying a custom MTU value, indicate the range of values in bytes.

  1. Click Next to continue creating the VPLS service definition and specify the connectivity settings.

Specifying Connectivity Settings

Connectivity Settings Field

Action

Route target

The Route target field is prepopulated with the Auto pick option.

Route distingquisher

The Route distinguisher field is prepopulated with the Auto pick option.

VLAN normalization

All VPLS service definitions require VLAN normalization.

Allow Multihoming

If you are using multihoming features, check the box.

MAC Security Settings

MAC learning

MAC learning is on by default for VPLS service definitions.

Interface MAC limit

The default value for Interface MAC limit is 1024. If you are using a different value, enter that value.

MAC table size

The table size is predetermined to correspond to the default MAC limit. If you are using a value other than the default, specify that value.

  1. Click Finish to see the service definition inventory list.
  2. Click on the unpublished service definition you just created.
  3. Right-click on the selected service definition to choose publishing options.
  4. Select the service definition and click Publish to save and publish the definition.
  5. The next step is to create the service order. In the Network Activate task pane, select Service Provisioning.