Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Specifying UNI Settings for Port-to-Port Services

    To set UNI attributes for a port-to-port service, complete the following procedure.

    1. Enter information in the UNI Settings window.
    2. Fill in the fields in the UNI Settings window according to the following table.

      Field

      Action

      Traffic Treatment Settings

      Ethernet option

      Select port-port from the list.

      The Ethernet option you choose determines the other options you can select and specify on the page.

      Customer traffic type

      Select N/A. For port-to-port services, all traffic is always transported.

      VLAN ID selection

      In port-to-port services, all traffic and all VLANs on one port are transported to all other ports.

      Editable in Service Order

      Select this check box to allow the service provisioner to override the MTU setting.

      Interface Settings

      Physical IF encapsulation

      Select ethernet-vpls, the only valid physical interface encapsulation method allowed for port-to-port services.

      Logical IF encapsulation

      You cannot change this field because it is not relevant to port-to-port services.

      MTU Settings

      Default MTU (Bytes)

      You can specify an MTU value in this field. The default value for MTU is 1522 bytes.

      To see the permitted range for the MTU value, select the Editable in Service Order check box. The MTU range is 1522 through 9192.

      MTU Range (Bytes)

      If you select the check box Editable in Service Order, you can specify a value range for MTU (in bytes). The permitted range for MTU is 1522 through 9192.

      Note: Ultimately, the system establishes the MTU by multiplying the value you specify in the Default MTU (Bytes) field by the value you specify for MTU Factor.

      Calculation of Burst-Size

      Calculate Burst Size

      Select the preferred option for calculating the burst size:

      • MTU Based

        If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

        The default value for MTU Factor is 1.

      • Line Rate Based

        If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

        The default value for Burst Period is 1.

      Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

      The following illustration shows the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

      Bandwidth Settings

      The following illustration shows the Bandwidth Settings panel, which appears if you do not select the Enable QoS check box in the preceding General settings window.

      Enable rate limiting (check box)

      If you select this check box, you can override the MTU setting.

      Default bandwidth (Mbps)

      Specify the default bandwidth value, in Mbps.

      Default: 10 Mbps

      Range: 1 Mbps through 100,000 Mbps

      Min Bandwidth (Kbps)

      To override the default bandwidth value, select the Editable in Service Order check box.

      Specify the minimum bandwidth value in Kbps:

      Default: 1000 Kbps

      Range: 64 Kbps through 100,000 Kbps

      Max Bandwidth (Mbps)

      Specify the maximum bandwidth value, in Mbps.

      Default: 100 Mbps

      Range: 1 Mbps through 100,000 Mbps

      The following table lists the Max Bandwidth (Mbps) for the M Series, MX Series, and ACX Series Routers:

      Table 1: Maximum Bandwidth for M Series, MX Series, and ACX Series Routers

      M Series IQ2E PIC

      M Series IQ2 PIC

      MX Series 3D PIC

      MX Series Non-3D PIC

      ACX 2000

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      32,000 Mbps or 32 Gbps

      32,000 Mbps or 32 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

      100,000 Mbps or 100 Gbps

      100,000 Mbps or 100 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

      Increment (Kbps)

      Specify a value in the range that is made available to the service provisioner.

    3. Click Next to continue with Connectivity settings.

    Modified: 2017-01-19