Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Creating a Point-to-Multipoint VPLS Service Definition

    This procedure provides the steps to create a definition for a point-to-multipoint Ethernet service. Point-to-multipoint services are also known as hub and spoke services.

    The standard service definitions that came with your initial software installation are designed to be appropriate for most requirements. You can also create a customized service definition—for example, to set different bandwidth limits on the service than those offered in the standard service definitions.

    When the new service definition is complete and published, network operators or service provisioners can use the completed service definition as a base for creating and then activating point-to-multipoint Ethernet services on the network.

    The windows appear in the order stated. You can, however, perform these steps in any order by accessing them through the task list in the right panel. If the panel is not visible, click the snap tool on the right side of the main display area.

    Specifying General Information for Point-to-Multipoint VPLS Service Definitions

    In the Network Activate task pane, select Service Design > Manage Service Definitions > Create VPLS Service Definition. The General settings window appears.

    To specify the general information for a point-to-multipoint service definition:

    1. Fill in the fields in the General window.

      Field

      Action

      Name

      Type a name for the service definition.

      Service type

      Select Point-to-Multipoint Ethernet (VPLS)

      Signaling

      Select signaling type:

      • BGP— If BGP signaling is selected, the following fields are available in the connectivity window:
        • Route target
        • Route distinguisher
        • VLAN normalization
        • Allow Multihoming
        • Mac Security Settings
        • VCID, if Enable PW Extension is enabled
      • LDP—If LDP signaling is selected, the following fields are available in the connectivity window:
        • Auto Discovery
        • Route target, if Auto Discovery is enabled
        • Route distinguisher, if Auto Discovery is enabled
        • VPLS ID, if Auto Discovery is disabled
        • VPN ID, if Auto Discovery is enabled
        • VLAN normalization
        • Mac Security Settings

      Note: The Signaling is not editable in the service order.

      Comments (Optional)

      Type a brief description or other comment that you want to appear in the Service Definition table.

      Enable QoS

      When you enable QoS in the service definition, you must specify a QoS profile in the service order to classify traffic into defined service groups to provide the special treatment of traffic across the network service. For example, voice traffic can be sent across certain links, and data traffic can use other links.

      Enable L3 Access

      Select this check box to create the link into Layer 3. If you enable the Layer 3 access, the available Ethernet option in the UNI Settings are:

      • port-port
      • dot1q
      • qinq
      • asymmetric tag depth

      Enable PW Extension

      Select this check box to enable pseudowire extension. You cannot edit this check box in the service order.

      Enable PW Resiliency

      Select this check box to enable resiliency. You cannot edit this field in the service order.

      If the Signaling type is BGP, you need to select the Enable PW Extension check box to enable the Enable PW Resiliency check box.

      For more information of pseudowire redundancy, see Redundant Pseudowires for Layer 2 Circuits and VPLS.

      Enable Static PW Labels

      Select this check box to enable a pseudowire connection by configuring static values.

      Note: The Enable Static PW Labels check box is enabled for both signaling types: LDP and BGP.

      When the signaling type is BGP, selection of this checkbox enables the Enable PW Resiliency checkbox and automatically selects the Enable PW Extension checkbox.

      Service Template Definition

      (Optional) To include a service template for the service, select a service template from the Service Template list.

      The selected service template appears in the Default Service Template field.

      You can select one or more service templates as the default service template. By default, the default service templates are attached to the endpoints.

      Note: You cannot add or delete a service template while creating a service order.

      The remaining service templates on the Service Template list are termed as optional service templates. You can attach the optional service templates to the endpoints on a need basis.

      In the View Service Definition Details window, the value for the default service template in the Default Service Template column is True.

      For instructions on creating a service template, see Creating a Service Template.

    2. Click Next to save the information. Continue with Specifying UNI Settings.

    Specifying UNI Settings

    In this step, you provide the UNI service attributes for this service definition. The attributes you set depend on whether you are setting attributes for ports, 802.1Q interfaces, or Q-in-Q interfaces:

    Specifying UNI Settings for Port-to-Port Services

    Note: You can select the port-port option only for services that are not normalized. That is, you must select Not Normalized when specifying the connectivity.

    To set UNI attributes for port UNIs:

    1. Fill in the fields as indicated in the table.

      Field

      Action

      Traffic Treatment Settings

      Ethernet option

      Select port-port from the drop-down list.

      The Ethernet option you choose determines the other options you can select and specify on the page.

      Customer traffic type

      Select N/A. For port-to-port services, all traffic is always transported.

      VLAN ID selection

      The VLAN ID cannot be selected. In port-to-port services, all traffic and all VLANs on one port are transported to all other ports.

      Editable in Service Order

      To allow the service provisioner to override the MTU setting, select the check box.

      Interface Settings

      Physical IF encapsulation

      In the Physical IF encapsulation box, select ethernet-vpls, which is the only valid physical interface encapsulation method for port-to-port services.

      The Logical IF encapsulation field cannot be selected because it is not relevant to port-to-port services.

      Logical IF encapsulation

      You cannot select a choice in this field because it is not relevant to port-to-port services.

      LDP PW Extension Settings

      Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General window.

      Physical IF encapsulation

      In the Physical IF encapsulation box, select ethernet-ccc, which is the only valid physical interface encapsulation method for port-to-port services.

      Logical IF encapsulation

      You can not select a choice in this field because it is not relevant to port-to-port services.

      MTU Settings

      In the MTU range boxes, type the lowest and highest values for MTU that the service provisioner can type.

      Calculation of Burst-Size

      Calculate Burst Size

      Select the preferred option for calculating the burst size:

      • MTU Based

        If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

        The default value for MTU Factor is 1.

      • Line Rate Based

        If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

        The default value for Burst Period is 1.

      Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

      The following illustration shows the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

      Bandwidth Settings

      The following illustration shows the Bandwidth Settings panel, which appears if you do not select the Enable QoS check box in the preceding General settings window.

      Enable rate limiting

      To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit.

      Note: Bandwidth settings are not available in the service definition when QoS Design software is installed.

      Default bandwidth (Mbps)

      Specify the default bandwidth value in Mbps.

      Default: 10 Mbps

      Range: 1 Mbps through 100,000 Mbps

      Min Bandwidth (Kbps)

      Specify the minimum bandwidth value in Kbps.

      Default: 1000 Kbps

      Range: 64 Kbps through 100,000 Kbps

      Max Bandwidth (Mbps)

      Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1

      Default: 100 Mbps

      Range: 1 Mbps through 100,000 Mbps

      Increment (Kbps)

      Specify a value that defines which values in the range is made available to the service provisioner.

      Default: 1000 Kbps

      Range: 64 Kbps through 100,000 Kbps

      The following table lists the Max Bandwidth (Mbps) for the M Series, MX Series, and ACX Series Routers:

      Table 1: Maximum Bandwidth for M Series, MX Series, and ACX Series Routers

      M Series IQ2E PIC

      M Series IQ2 PIC

      MX Series 3D PIC

      MX Series Non-3D PIC

      ACX 2000

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      GE Port (1G)

      XE Port (10G)

      32,000 Mbps or 32 Gbps

      32,000 Mbps or 32 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

      100,000 Mbps or 100 Gbps

      100,000 Mbps or 100 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

      50,000 Kbps or 50 Gbps

    2. Click Next to save the UNI settings. Continue with Specifying Connectivity and MAC Security Information.

    Specifying UNI Settings for Services with 802.1Q Interface Types

    To set UNI attributes for 802.1Q interfaces:

    1. Fill in the fields as indicated in the table.

      Field

      Action

      Traffic Treatment Settings

      Ethernet option

      Select dot1q from the drop-down list.

      The Ethernet option you choose determines the other options you can select and specify on the page.

      Customer traffic type

      Select a traffic type to restrict the traffic that can be transported across the network for the service:

      • Select Transport single vlan to transport the traffic for a specific VLAN across the network. Single VLAN is the only option for 802.1Q interface types. You need to specify the Outer Tag protocol ID.

        Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands:

        set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100
        set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8
        set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100
      • Select Transport vlan range to transport the traffic for a range of VLANs across the network.

      Note: Make sure to check Editable in Service Order if you want the service provisioner to be able to override this setting.

      VLAN ID selection

      In the VLAN ID selection box, specify how the VLAN ID is determined:

      • To allow the service provider to specify the VLAN ID, choose Select manually. This option is used typically when no VLAN normalization is applied.

        Specify the VLAN ID range in VLAN range for manual input.

        Range: 1 through 4094

        To enable the service provisioner to override this setting, select Editable in Service Order.

      • To cause the VLAN ID to be selected automatically from the VLAN ID pool, select Auto pick. This option is used typically when VLAN normalization is applied.

        Specify the VLAN ID pool in VLAN range for auto-pick

        Range: 1 through 4094

        To enable the service provisioner to override this setting in a service order, select Editable in Service Order.

      To enable the service provisioner to override this setting in a service order, select Editable in Service Order.

      VLAN range for auto-pick

      Specify the VLAN ID pool.

      Range: 1 through 4094

      VLAN range for manual input

      Specify the VLAN ID range.

      Range: 1 through 4094

      Outer Tag protocol ID

      Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN:

      • 0x88a8
      • 0x8100
      • 0x9100

      Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands:

      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100
      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8
      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100

      Editable in Service Order

      To allow the service provisioner to override the MTU setting, select the check box for those options.

      Interface Settings

      Physical IF encapsulation

      In the Physical IF encapsulation box, select the default physical encapsulation scheme to be used by service orders based on this service definition. For point-to-multipoint services with 802.1Q interfaces, the only option is flexible-ethernet-services.

      Logical IF encapsulation

      The Logical IF encapsulation field is constrained by your selection in the Physical IF encapsulation field. For the physical encapsulation mode of flexible-ethernet-services, your only option is to select vlan-vpls for the logical encapsulation method.

      LDP PW Extension Settings

      Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General window.

      Physical IF encapsulation

      In the Physical IF encapsulation box, select one of the following options:

      • vlan-ccc
      • extended-vlan-ccc
      • flexible-ethernet-services

      Logical IF encapsulation

      The Logical IF encapsulation field is constrained by your selection in the Physical IF encapsulation field.

      For the physical encapsulation mode of vlan-ccc or flexible-ethernet-services, your only option is to select vlan-ccc for the logical encapsulation method.

      For the physical encapsulation mode of extended-vlan-ccc, your only option is to select extended-vlan-ccc for the logical encapsulation method.

      MTU Settings

      In the Default MTU box, specify the MTU for each UNI.

      To allow the service provisioner to override the MTU setting, select Editable in Service Order and, in the MTU range boxes, type the highest and lowest MTU values that the service provisioner can type.

      Calculation of Burst-Size

      Calculate Burst Size

      Select the preferred option for calculating the burst size:

      • MTU Based

        If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

        The default value for MTU Factor is 1.

      • Line Rate Based

        If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

        The default value for Burst Period is 1.

      Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

      The following illustration shows the appearance of the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

      Bandwidth Settings

      The following illustration shows the Bandwidth Settings panel, which appears if you do not select the Enable QoS check box in the preceding General settings window.

      Enable rate limiting

      To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit.

      Note: Bandwidth settings are not available in the service definition when QoS Design software is installed.

      Default bandwidth (Mbps)

      Specify the default bandwidth value in Mbps.

      Default: 10 Mbps

      Range: 1 Mbps through 100000 Mbps

      Min Bandwidth (Kbps)

      Specify the minimum bandwidth value in Kbps.

      Default: 1000 Kbps

      Range: 64 Kbps through 100000 Kbps

      Max Bandwidth (Mbps)

      Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1

      Default: 100 Mbps

      Range: 1 Mbps through 100000 Mbps/100Gbps

      Increment (Kbps)

      Specify a value that defines which values in the range is made available to the service provisioner.

      Default: 1000 Kbps

      Range: 64 Kbps through 100000 Kbps

    2. Click Next to save the UNI settings. Continue withSpecifying Connectivity and MAC Security Information.

    Specifying UNI Settings for Services with Q-in-Q Interface Types

    To set UNI attributes for Q-in-Q interfaces:

    1. Fill in the fields as indicated in the table.

      Field

      Action

      Traffic Treatment Settings

      Ethernet option

      Select qinq from the drop-down list.

      The window expands to include options specific to Q-in-Q interfaces.

      Customer traffic type

      In the Customer traffic type box:

      • Select Transport all traffic to transport the traffic from all VLANs across the network. You need to specify only the Outer Tag protocol ID.

        Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100.

      • Select Transport single vlan to transport the traffic for a specific VLAN across the network. Single VLAN is the only option for 802.1Q interface types. You need to specify the Outer Tag protocol ID and the Inner Tag protocol ID.
      • Select Transport vlan range to limit the traffic across the network to a specific range of VLANs.

        If you select this option, the service provisioner will be prompted for the VLAN-ID range when creating a service order based on this service definition. You need to specify the Outer Tag protocol ID and the Inner Tag protocol ID.

      VLAN ID selection

      In the VLAN ID selection box, specify how the service VLAN ID is set during service order creation:

      • To cause the provisioning software to automatically select the service VLAN ID from the VLAN ID pool, select Auto pick. This option is used typically when no VLAN normalization is applied.

        Specify the VLAN ID pool in VLAN range for auto-pick

        Range: 1 through 4094

      • To allow the service provisioner to specify the service VLAN ID, choose Select manually. This option is used typically when VLAN normalization is applied.

        Specify the VLAN ID range in VLAN range for manual input.

        Range: 1 through 4094

      To enable the service provisioner to override this setting, select the Editable in Service Order check box.

      VLAN range for auto-pick:

      Specify the VLAN ID pool.

      Range: 1 through 4094

      VLAN range for manual input

      Specify the VLAN ID range.

      Range: 1 through 4094

      Outer Tag protocol ID

      Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN:

      • 0x88a8
      • 0x8100
      • 0x9100

      Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands:

      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100
      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8
      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100

      Inner Tag protocol ID

      Select the inner tag protocol ID:

      • 0x88a8
      • 0x8100
      • 0x9100

      Note: You cannot specify the Inner Tag protocol ID if the Customer traffic type is Transport single VLAN.

      Editable in Service Order

      To allow the service provisioner to override the MTU setting, select the check box for those options.

      Interface Settings

      Physical IF encapsulation

      In the Physical IF encapsulation box, select the default physical encapsulation scheme to be used by service orders based on this service definition. For point-to-multipoint services with Q-in-Q interfaces, the only option is flexible-ethernet-services.

      Logical IF encapsulation

      The Logical IF encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of flexible-ethernet-services, your only option is to select vlan-vpls for the logical encapsulation method.

      LDP PW Extension Settings

      Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General window.

      Physical IF encapsulation

      In the Physical IF encapsulation box, select one of the following options:

      • vlan-ccc
      • extended-vlan-ccc
      • flexible-ethernet-services

      Logical IF encapsulation

      The Logical IF encapsulation field is constrained by your selection in the Physical IF encapsulation field.

      For the physical encapsulation mode of vlan-ccc or flexible-ethernet-services, your only option is to select vlan-ccc for the logical encapsulation method.

      For the physical encapsulation mode of extended-vlan-ccc, your only option is to select extended-vlan-ccc for the logical encapsulation method.

      MTU Settings

      In the Default MTU box, specify the MTU for each UNI.

      To allow the service provisioner to override the MTU setting, select the Editable in Service Order check box and, in the MTU range boxes, type the lowest and highest values for the MTU that the service provisioner can type.

      Calculation of Burst-Size

      Calculate Burst Size

      Select the preferred option for calculating the burst size:

      • MTU Based

        If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

        The default value for MTU Factor is 1.

      • Line Rate Based

        If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

        The default value for Burst Period is 1.

      Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

      The following illustration shows the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

      Bandwidth Settings

      The following illustration shows the Bandwidth Settings panel, which appears if you do not select the Enable QoS check box in the preceding General settings window.

      Enable rate limiting

      To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit.

      Note: Bandwidth settings are not available in the service definition when QoS Design software is installed.

      Default bandwidth (Mbps)

      Specify the default bandwidth value in Mbps.

      Default: 10 Mbps

      Range: 1 Mbps through 100000 Mbps

      Min Bandwidth (Kbps)

      Specify the minimum bandwidth value in Kbps.

      Default: 1000 Kbps

      Range: 64 Kbps through 100000 Kbps

      Max Bandwidth (Mbps)

      Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1

      Default: 100 Mbps

      Range: 1 Mbps through 100000 Mbps

      Increment (Kbps)

      Specify a value that defines which values in the range is made available to the service provisioner.

      Default: 1000 Kbps

      Range: 64 Kbps through 100000 Kbps

    2. Click Next to save the UNI settings. Continue withSpecifying Connectivity and MAC Security Information.

    Specifying UNI Settings for Services with Flexible VLAN Tagging (Asymmetric Interface Types)

    You can specify the Ethernet option asymmetric tag depth to create a service that includes any combination of port-based interfaces, 802.1Q interfaces, and Q-in-Q, interfaces.

    To set UNI attributes for asymmetric interfaces:

    1. Fill in the fields as indicated in the table.

      Field

      Action

      Traffic Treatment Settings

      Ethernet option

      Select asymmetric tag depth from the drop-down list.

      Customer traffic type

      In the Customer traffic type box:

      • Select Transport all traffic to transport the traffic from all VLANs across the network. You need to Specify only the Outer Tag protocol ID.

        Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100.

      • Select Transport single vlan to transport the traffic for a specific VLAN across the network. Single VLAN is the only option for 802.1Q interface types. You need to specify the Outer Tag protocol ID and the Inner Tag protocol ID.
      • Select Transport vlan range to limit the traffic across the network to a specific range of VLANs.

        If you select this option, the service provisioner will be prompted for the VLAN-ID range when creating a service order based on this service definition. You need to specify the Outer Tag protocol ID and the Inner Tag protocol ID.

      VLAN ID selection

      In the VLAN ID selection box, specify how the service VLAN ID is set during service order creation:

      • To cause the provisioning software to automatically select the service VLAN ID from the VLAN ID pool, select Auto pick. This option is used typically when no VLAN normalization is applied.

        Specify the VLAN ID pool in VLAN range for auto-pick

        Range: 1 through 4094

      • To allow the service provisioner to specify the service VLAN ID, choose Select manually. This option is used typically when VLAN normalization is applied.

        Specify the VLAN ID range in VLAN range for manual input.

        Range: 1 through 4094

      To enable the service provisioner to override this setting, select the Editable in Service Order check box.

      VLAN range for auto-pick:

      Specify the VLAN ID pool.

      Range: 1 through 4094

      VLAN range for manual input

      Specify the VLAN ID range.

      Range: 1 through 4094

      Outer Tag protocol ID

      Select the outer tag protocol ID if the Customer traffic type is Transport single VLAN:

      • 0x88a8
      • 0x8100
      • 0x9100

      Note: For an interface, you must configure a physical port with the possible Tag Protocol Identifiers (TPID) either manually or through a template. Otherwise, the service creation fails for all TPIDs except 0x8100. To configure the TPIDs manually, use the following commands:

      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x9100
      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x88a8
      set interfaces ae0 aggregated-ether-options ethernet-switch-profile tag-protocol-id 0x8100

      Inner Tag protocol ID

      Select the inner tag protocol ID:

      • 0x88a8
      • 0x8100
      • 0x9100

      Note: You cannot specify the Inner Tag protocol ID if the Customer traffic type is Transport all traffic.

      Editable in Service Order

      To allow the service provisioner to override the MTU setting, select the check box for those options.

      Interface Settings

      Physical IF encapsulation

      Select the default physical encapsulation scheme to be used by service orders based on this service definition. We recommend you select flexible-ethernet-services.

      For multipoint-to-multipoint services with Q-in-Q interfaces, the only option is flexible-ethernet-services

      Logical IF encapsulation

      The Logical IF encapsulation field is constrained by your selection in the Physical Interface Encapsulation field. For the physical encapsulation mode of flexible-ethernet-services, your only option is to select vlan-vpls for the logical encapsulation method.

      LDP PW Extension Settings

      Note: The LDP PW Extension Settings is available only if you have selected the Enable PW Extension check box in the General window.

      Physical IF encapsulation

      In the Physical IF encapsulation box, select one of the following options:

      • vlan-ccc
      • extended-vlan-ccc
      • flexible-ethernet-services

      Logical IF encapsulation

      The Logical IF encapsulation field is constrained by your selection in the Physical IF encapsulation field.

      For the physical encapsulation mode of vlan-ccc or flexible-ethernet-services, your only option is to select vlan-ccc for the logical encapsulation method.

      For the physical encapsulation mode of extended-vlan-ccc, your only option is to select extended-vlan-ccc for the logical encapsulation method.

      MTU Settings

      In the Default MTU box, specify the MTU for each UNI.

      To allow the service provisioner to override the MTU setting, select the Editable in Service Order check box and, in the MTU range boxes, type the lowest and highest values for the MTU that the service provisioner can type.

      Calculation of Burst-Size

      Calculate Burst Size

      Select the preferred option for calculating the burst size:

      • MTU Based

        If you select the option MTU Based, you can specify a value for MTU Factor in the range 1 through 1087902.

        The default value for MTU Factor is 1.

      • Line Rate Based

        If you select the option Line Rate Based, you can specify a value for Burst Period in the range 1 through 7450 milliseconds.

        The default value for Burst Period is 1.

      Note: The Calculate Burst Size list is enabled only when you select the Enable rate limiting checkbox.

      The following illustration shows the Calculate Burst-Size panel parameters if you select the Line Rate Based option.

      Bandwidth Settings

      The following illustration shows the Bandwidth Settings panel, which appears if you do not select the Enable QoS check box in the preceding General settings window.

      Enable rate limiting

      To enable a service provisioner to limit the available bandwidth, select this check box, and type a default bandwidth limit.

      Note: Bandwidth settings are not available in the service definition when QoS Design software is installed.

      Default bandwidth (Mbps)

      Specify the default bandwidth value in Mbps.

      Default: 10 Mbps

      Range: 1 Mbps through 100000 Mbps

      Min Bandwidth (Kbps)

      Specify the minimum bandwidth value in Kbps.

      Default: 1000 Kbps

      Range: 64 Kbps through 100000 Kbps

      Max Bandwidth (Mbps)

      Specify the maximum bandwidth value in Mbps. For more information on maximum bandwidth see Table 1

      Default: 100 Mbps

      Range: 1 Mbps through 100000 Mbps

      Increment (Kbps)

      Specify a value that defines which values in the range is made available to the service provisioner.

      Default: 1000 Kbps

      Range: 64 Kbps through 100000 Kbps

    2. Click Next to save the UNI settings. Continue withSpecifying Connectivity and MAC Security Information.

    Specifying Connectivity and MAC Security Information

    In this step, you specify the attributes that define the connectivity among remote sites across the service provider network and the service security. The following is a sample Connectivity window.


    To configure connectivity between sites across the network:

    1. Fill in the fields in the Connectivity window.

      Field

      Action

      Route target

      Choose one of the following options from the list:

      • Auto pick
      • Select manually

      This field is available in either of the following cases:

      • The Signaling type is BGP.
      • The Signaling type is LDP and Auto Discovery is enabled.

      Route distinguisher

      Select a route distinguisher option:

      • Select manually—The service provider specifies the route distinguisher.
      • Auto pick—The route distinguisher is selected automatically.

      To override this setting in the service order, select the Editable in Service Order check box.

      This field is available in either of the following cases:

      • The Signaling type is BGP.
      • The Signaling type is LDP and Auto Discovery is enabled.

      VLAN normalization

      Select a value:

      • Normalize to VLAN all—To preserve customer VLAN IDs (and customer QoS priorities) across the network.

        Note: For services that transport a range of VLAN IDs, you must set VLAN Normalization to all. You cannot transport a range of VLAN IDs without normalization.

      • Normalized VLAN none—To preserve no VLAN IDs across the network
      • Not normalized—If VLAN IDs are to be provided manually and are required to match each endpoint
      • Normalized to Dot1q—To transport only single-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network.
      • Normalized to QinQ—To transport only double-tagged frames across the network core. All port, dot1q , and Q-in-Q traffic is transported across the network.
      • Normalization not required—To specify no normalization for port-to-port services

      For more information about VLAN normalization, see Junos Space Layer 2 Services Overview.

      For information about VLAN manipulation, see Understanding VLAN Manipulation (Normalization and VLAN Mapping) on Ethernet Services.

      Allow Multihoming

      This check box is available only if the signaling type is BGP.To enable a service provisioner to define primary and backup PE devices in a multihomed group that serves a single customer site, select Allow Multihoming.

      Auto Discovery

      You cannot enable or disable the Auto Discovery check box if you have enabled the Enable PW Extension or the Enable PW Resiliency check boxes.

      This check box is available only if the signaling type is LDP.

      Note: If the Enable Static PW Labels checkbox in the General window is checked for the LDP signaling, then the Auto Discovery checkbox is disabled in the Connectivity Settings page.

      The Auto Discovery checkbox is not available on the Connectivity Settings page when the signaling type is BGP.

      On enabling the auto discovery, the following fields are available:

      • Route target
      • Route distinguisher
      • VPN ID

      On disabling the auto discovery specify the VPLS ID.

      VPLS ID

      This field is available only if the signaling type is LDP and auto discovery is disabled.

      Identifies the virtual circuit identifier used for the VPLS routing instance.

      • Autopick
      • Select manually

      VPN ID

      This field is available only if the signaling type is LDP and auto discovery is enabled.

      Identifies the VPN ID associated with the router.

      • Autopick
      • Select manually

      Revert time (sec)

      This field is available only if the Enable PW Resiliency is enabled.

      Revert time for redundant Layer 2 circuits and VPLS pseudowires.

      Default: 5 seconds

      Range: 0 through 65,535 seconds

      Switch Over Delay (sec)

      This field is available only if the Enable PW Resiliency is enabled.

      Specify the delay to wait before the backup pseudowire takes over.

      Default: 0 second

      Range: 0 through 180 seconds

      VCID

      This field is available only if the Service type is point-to-multipoint, the Signaling is BGP, and the Enable PW Extension is enabled.

      The VCID can be either set automatically by the Junos Space software, or it can be set manually by the service provisioner in the service order.

      MAC learning

      To enable MAC learning, select the check box.

      Interface MAC limit

      Maximum number of MAC addresses learned from an interface.

      Range: 1 through 131071 MAC addresses per interface

      MAC statistics

      To enable MAC statistic, select the check box.

      MAC table size

      Modify the size of the MAC address table for the bridge domain.

      Range: 16 through 1048575

      To allow the service provisioner to override the MAC settings, select Editable in Service Order.

    2. Click Next to save the connectivity settings and continue with Specifying Advanced Settings.

    Specifying Advanced Settings

    In this step, you can specify the parameters that define advanced connectivity between sites across the service provider network. The following illustration shows the Advanced window.


    To specify advanced settings:

    1. Fill in the fields as indicated in the table.

      Field

      Action

      Include

      Select the Include check box for each advanced setting that you want to include in the service definition.

      Note: If you select any advanced parameters for a service definition, you must also select the Include check box for the Disable tunnel services parameter, and select or clear the Disable tunnel services check box.

      For MX Series devices, if you deploy a VPLS service without selecting the Include check box for Disable tunnel services parameter, the VPLS service is down. As a work around, you can push the configuration to each PE device for the service by running the following command:

      root@test_device# set chassis fpc 0 pic 1 tunnel-services bandwidth 1g

      Disable tunnel services

      Enable or disable tunnel-services to specify that traffic for particular VPLS routing instances be forwarded to specific virtual tunnel (VT) interfaces.

      • To enable tunnel-services, clear the Disable tunnel-services check box.
      • To disable tunnel-services, select the Disable tunnel-services check box (default).

      Disable local-switching

      Enable or disable local switching. In local switching mode, you can terminate multiple Layer 2 circuit pseudowires at a single VPLS mesh group:

      • To enable local switching across the network, clear the Disable local-switching check box.
      • To disable local switching across the network, select the Disable local-switching check box (default).

      fast-reroute-priority

      In the fast-reroute-priority, specify the reroute priority for a VPLS routing instance:

      • HIGH—Set the fast reroute priority for a VPLS routing instance to high. During a fast reroute event, the router repairs next hops for high-priority VPLS routing instances first.
      • MEDIUM—Set the fast reroute priority for a VPLS routing instance to medium. During a fast reroute event, the router repairs next hops for medium-priority VPLS instances after high-priority VPLS routing instances but before low-priority VPLS routing instances.
      • LOW—Set the fast reroute priority for a VPLS routing instance to low, which is the default. During a fast reroute event, the router repairs next hops for low-priority VPLS routing instances last.

      Label block size

      Configure the label block size for VPLS labels by using one of the following values.

      • 2—Allocate the label blocks in increments of 2. Use this setting for a VPLS domain that has only two sites with no future expansion plans.
      • 4—Allocate the label blocks in increments of 4.
      • 8 —Allocate the label blocks in increments of 8. This is the default.
      • 16—Allocate the label blocks in increments of 16. A label block size of 16 enables you to minimize the number of routes in the VPLS domain. Use this setting only if the number of routes is the primary concern.

      Note: This field is unavailable if the Signaling type is LDP and the Auto discovery is enabled.

      Connectivity type

      Select a connection-type to specify when a VPLS connection is taken down, depending on whether the interface for the VPLS routing instance is customer-facing or integrated routing and bridging (IRB):

      • ce—Require that for the VPLS connection to be up, the customer-facing interface for the VPLS routing instance must also be up. If the customer-facing interface fails, the VPLS connection is taken down. This is the default.
      • irb—Allow a VPLS connection to remain up so long as an IRB interface is configured for the VPLS routing instance.

      Note: This field is unavailable if the Signaling type is LDP and the Auto discovery is enabled.

      Editable in Service Order

      By default, each advanced setting that you include in the service definition can be edited in the service order. To prevent the service provisioner from overriding an advanced setting in the service order, clear the Editable in Service Order check box.

    2. Click Finish to save the advanced settings.

      The service definition is complete.

    Modified: 2017-02-21