Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Example: Base Configuration for BX7000 Multi-Access Gateway Supporting ATM and TDM Pseudowires

    The configuration shown here is the base configuration required for a BX7000 Multi-Access Gateway to support ATM and TDM Pseudowires. This configuration shows 3 Gigabit Ethernet interfaces and 16 T1 interfaces that can be used for ATM or TDM pseudowires.

    root@bx-csr0> show configuration 
    system { 
        host-name bx-csr0;
        services ntp ;
        framer-mode t1;
        manual-mode config disable;
        zerotouch config disable;
        ssh protocol-version both;
        services ssh enabled;
    } 
    interface {
        ge-1/0/0 {                      #ge interfaces are NNI interfaces
            admin-state enable;
            unit 0 {
                family inet address 192.168.183.138/25;
            }
        }
        ge-1/0/1 {
            admin-state enable;
            unit 0 {
                family inet address 10.10.183.138/25;
            }
        }
        ge-1/0/2 {
            admin-state enable;
            unit 0 {
                family inet address 10.0.88.2/30;
            }
        }
        lo0 {                                #lookback 
            admin-state enable;
            unit 0 {
                family inet address 100.100.200.1/32;
            }
        }
        t1-0/0/0 { #t1-0/0/0, t1-0/0/1,t1-0/0/10-t1-0/0/15 here are for TDM P/W service deployment
            admin-state enable;
        }
        t1-0/0/1 {
            admin-state enable;
        }
        t1-0/0/10 {
            admin-state enable;
        }
        t1-0/0/11 {
            admin-state enable;
        }
        t1-0/0/12 {
            admin-state enable;
        }
        t1-0/0/13 {
            admin-state enable;
        }
        t1-0/0/14 {
            admin-state enable;
        }
        t1-0/0/15 {
            admin-state enable;
        }
        t1-0/0/2 { #t1-0/0/2 -t1-0/0/9 here are for ATM P/W service deployment
            admin-state enable;
            encapsulation atm;
        }
        t1-0/0/3 {
            admin-state enable;
            encapsulation atm;
        }
        t1-0/0/4 {
            admin-state enable;
            encapsulation atm;
        }
        t1-0/0/5 {
            admin-state enable;
            encapsulation atm;
        }
        t1-0/0/6 {
            admin-state enable;
            encapsulation atm;
        }
        t1-0/0/7 {
            admin-state enable;
            encapsulation atm;
        }
        t1-0/0/8 {
            admin-state enable;
            encapsulation atm;
       }
        t1-0/0/9 {
            admin-state enable;
            encapsulation atm;
        }
    }
    protocols {
        ospf {
            admin-state enable;
            spf-delay 200;
            traffic-engineering enable;
            area 0.0.0.0 {
                interface ge-1/0/2 {
                    admin-state enable;
                } 
                interface lo0 {
                    admin-state enable;
                    mode passive;
                } 
            }
        }
        ldp {
            admin-state enable;			 
            mpls ldp targeted-hello send remote-peer-ip; #this needs to be added manually 
    			interface ge-1/0/2 {
                admin-state enable;
            } 
            interface ge-1/0/1 {
                admin-state enable;
            } 
            interface ge-1/0/0 {
                admin-state enable;
            } 
    }
    
    rsvp {
            admin-state enable;
            interface ge-1/0/2 {
                admin-state enable;
                reliable enable;
                hello-interval 20;
            }
    }
    mpls {
            label-switch-path p2pdbx1_32793 { #existing LSP is optional; one may use Space Transport Activate to create such
                to-address 192.168.5.1;
                from-address 100.100.200.1;
                primary p2pdbx1_32793 {
                    priority 7 0;
                } 
                path 10.100.200.100 loose;
            }
            
            static-path-inet st1_32770 { #existing static LSP is optional; one may use Space Transport Activate to create such
                push 3;
                next-hop-address 10.0.88.1;
                out-interface ge-1/0/2;
                ingress-address 100.100.200.1;
                egress-address 192.168.5.1;
            }
            
            interface ge-1/0/2 {
                admin-state enable;
            } 
            interface ge-1/0/1 {
                admin-state enable;
            } 
            interface ge-1/0/0 {
                admin-state enable;
            }
    }
        snmp { 
            community-name public
            contact bx-admin;
        }
    } 
    connection { 
    } 
    policy-options {
    } 
    bridge-domains {
    } 
    static-route {
        route 0.0.0.0/0 {
            next-hop 192.168.183.254;
        }
    } 
    routing-options {
        autonomous-system 65410;
    }
    
    

    Modified: 2017-02-02