Assigning a Fabric Profile to Devices and Ports
A Fabric profile contains configuration settings for a gateway Fibre Channel (FC) fabric. You can assign an existing user-created or system-created Fabric profile to devices and FC ports to configure FC fabrics, using the steps described in this topic. A Fabric profile can be assigned to a QFX3500 device in standalone mode or to a QFabric Node.
Gateway FC fabrics on a QFabric system are called local FC fabrics. A local FC fabric does not span Node devices and does not span the fabric Interconnect device. Local FC fabrics are entirely contained on a single Node device. You can assign multiple interfaces on one Node device to a gateway FC fabric.
This topic describes:
Assigning a Fabric Profile
To assign a Fabric profile:
- From the Network Director Banner, select Build mode.
- In the Tasks pane, select Wired > Profiles > Fabric.
The Manage Fabric profiles page appears. The page displays all the Fabric profiles that you configured as well as the system-created profiles detected during device discovery.
- Select a profile from the list of profiles and click Assign.
The Assign Fabric Profile wizard opens to the Device Selection page.
If Network Director fails to read the configuration of one or more devices after the device discovery, such devices are not displayed in the Assign Profile page. You will not be able to assign profiles to such devices. The Manage Jobs page in System mode displays details of the device discovery jobs. Use the information displayed on this page to take appropriate corrective steps to enable Network Director to reread the configuration of the failed device. For more information, see Discovering Devices in a Physical Network.
- Enable either Select Devices or Select Port Groups.
- If you enabled Select Port Groups, select one or more port groups from the Select Port Group list.
- If you enabled Select Devices during Object
Selection, expand the list of objects and select the objects that
contain the devices and interfaces you want to assign by clicking
the check box next to them.
If you select a container node, all devices under that node are selected. The list of objects is filtered to include only devices that match the profile’s family type. Be sure that a check mark appears in the corresponding check box—highlighting the object name is not sufficient.
- Click either Next or Profile Assignment.
The Profile Assignment page displays the list of existing assignments in the Assignments table.
- To assign the profile to an entire device, select the
device from the Assignments table, then click the Assign button, then select Assign to Device.
If you assign the profile to a device but not to ports on the device, the fabric will be created on the device, but no FC ports will be assigned to the fabric. You must assign FC ports to the profile to add them to the fabric.
- To assign the profile to ports within the selected objects:
- Select one or more container nodes or devices from the
To assign the profile to nonconsecutive interfaces or to aggregated Ethernet interfaces, select a single device.
To assign the profile to interfaces in the same consecutive interface range (for example, ge-0/0/0 through ge-0/0/15) on one or more devices, select one or more devices. To make multiple selections, press Shift or Ctrl while making the selections.
To assign a profile to ports within a QFabric system select the member node group or groups that contain the ports.
To assign a profile to ports within a Virtual Chassis Fabric (VCF), you can select any container nodes or member devices within the VCF, including the VCF container node.
To assign a profile to aggregated Ethernet ports within a Virtual Chassis or VCF, select the Virtual Chassis or VCF container node. To assign a profile to physical device ports within a Virtual Chassis or VCF, select one or more member devices.
Channelized ports are only applicable for Data Center Switching ELS devices and only XE interfaces can be used as channelized ports.
- Click the Assign to Port button.
The Assign Profile to Ports window opens.
- Select either Ports (default) or Port Range. If you selected multiple devices in the previous step, you cannot choose the Port option.
- If you selected the Port option, select the ports from the list of ports.
- If you selected the Port Range option, enter the port
- In the Normal Ports section, enter a first and last port name in the text boxes, then click the Add button. The port range appears in the Selected Port Range section.
- Repeat the add process to add any additional port ranges.
- To delete a port range, select its check box, then click the Delete button.
At least one port within the port range must be available on each selected device for the port range to succeed. Assignments are created for the ports within the port range that are available. You can assign the profile to the same interface on multiple devices by entering the interface name in both fields of the port range.
- Click Assign to complete the port assignments and close the window.
- Select one or more container nodes or devices from the Assignments list:
- To configure object-specific attributes for an interface:
- Click Define from the interface’s Attributes column in the Assignments table.
The Configure attributes page opens.
- Configure the attributes.
For information about these attributes, see Table 1.
- Click Save.
- Click Define from the interface’s Attributes column in the Assignments table.
- On the Profile Assignment page, you can view the assignment
details for the selected device and also remove any assignments:
To view the assignment details, select the device and click View Assignments.
The Profile Details page for selected device appears. Expand the Device name to view the details of the assignment. The assignment status displays the status whether the device is deployed or is pending device update, and so on.
To delete a device from the assignment list, select the device from the Assignments table and click Remove.
- Click Next or click Review from the top wizard workflow to review the assignments. Use the Edit button if you want to edit the profile assignment.
- Click Finish once you are done reviewing the
After you click Finish, the Create Profile Assignments Job Details dialog box appears, which reports on the status of the profile assignment job. If you have assigned the profile to a large number of objects, the profile assignment job can take some time to complete. Instead of waiting for the Job Details dialog box to report job completion status, you can close it and check the details of the profile assignment job at a later time using the Manage Job task in System mode.
If any assignment fails, the profile assignment job fails and none of the assignments are created. Check the details for the profile assignment job for information about why the assignment failed.
Table 1: Fabric Profile Object-Specific Interface Attributes
Keep Alive Interval
Set the global interval between periodic FIP keepalive advertisements, in milliseconds. The range is 250 through 90,000 milliseconds. The default is 8000 milliseconds.
Set the global priority value associated with the switch FCF-MAC. CNAs use the priority value to determine the switch with which they will perform FIP FLOGI. The lower the value, the higher the priority. The switch advertises this value to the server ENodes on the FCoE network.
The range is 0 through 255. The default value is 128.
After you assign a Fabric profile to a device, you can deploy the profile from the Deploy mode. For details, see Deploying Configuration to Devices.
To view the details of a profile, select the profile from the Manage Fabric Profiles page and click the Details button.
Editing the Assignments of a Fabric Profile
To edit a Fabric profile’s device and port assignments:
- Select a profile from the Manage Fabric Profile page and
click Edit Assign.
The Edit Assignments page opens.
- Expand the nodes in the list to locate the devices and ports you want to change.
- To delete a device or port from a profile, click Delete in the Operation column of the device or
An X appears in the Record Status column.
- To delete multiple devices or ports from a profile, select
the devices or ports, then click the Delete button.
An X appears in the Record Status column of the deleted devices or ports.
- To change a device or port’s attributes, click Define in the Attributes column of the device or
port, then modify the attributes using the Configure attributes window.
A pencil icon appears in the Record Status column of the edited device or port.
- When you are done making assignment changes, click Apply.
The Manage Fabric Profile page opens.