Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

100-Gigabit Ethernet PIC with CFP2 (PTX Series)

 

Software Release

  • PTX5000: Junos OS Release 14.1 and later

Hardware Features

  • Four 100-Gigabit Ethernet ports

  • Model number: P2-100GE-CFP2

  • Name in the CLI: 4x100GE CFP2

  • Power requirements: 1.66A@ –48 V (90W)

  • Large maximum transmission units (MTUs): up to 9500 bytes

Software Features

Table 1 shows the first supported release for each software feature.

Table 1: Software Features Supported

Software Feature

PTX5000 First Supported Junos OS Release

Flexible-ethernet-services encapsulation

14.1

Flexible VLAN tagging

14.1

IFINFO / IFMON

14.1

IEEE 802.1 ag OAM

14.1

IEEE 802.3 ah OAM

14.1

IEEE 802.3ad link aggregation

14.1

Interrupt-driven link-down detection for MPLS FRR

14.1

MAC accounting per logical interface for source addresses

14.1

MAC filter per port for destination addresses and source addresses

14.1

MAC filter per logical interface for source addresses

14.1

SNMP

14.1

Up to 4000 logical interfaces share across all ports on a single PFE

14.1

Cables and Connectors

The following transceivers are supported on this PIC:

  • CFP2-100G-LR4-D—Supports 100GBASE-LR4

    • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

    • Connector: LC

  • CFP2-100G-SR10-D—Supports 100GBASE-SR10

    • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

    • Connector: 24-fiber MPO

  • CFP2-100GBASE-LR4—Supports 100GBASE-LR4

    • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

    • Connector: LC

  • CFP2-100GBASE-SR10—Supports 100GBASE-SR10

    • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

    • Connector: 24-fiber MPO

Note

The dual-rate transceiver (CFP2-100G-LR4-D) cannot be configured to use OTN framing when used in this PIC. The 100-Gigabit Ethernet OTN PIC with CFP2 (P2-100GE-OTN) supports OTN framing.

LEDs

The STATUS LED is located to the left of the ONLINE/OFFLINE button. One LED is located next to each port to indicate the link activity of the port. Table 2 describes the functions of these LEDs.

Table 2: 100-Gigabit Ethernet PIC with CFP2 LEDs

Label

Color

State

Description

STATUS

Green

On steadily

PIC is online with no alarms or failures.

Yellow

On steadily

PIC is initializing.

Red

On steadily

PIC has an error or failure.

Off

PIC is offline or not enabled and safe to remove from the router.

Single LED per port

Green

On steadily

Port is online with no alarms or errors, and the link is up.

Blinking

There is link activity on the port.

Red

On steadily

Port is on but the link is down, and the port has detected a failure.

Off

Port is off or not enabled.

Alarms, Errors, and Events

  • Laser bias current high/low alarms and warnings

  • Laser Rx power high/low alarms and warnings

  • Module not ready alarm

  • Module low power alarm

  • Module temperature high/low alarms and warnings

  • Rx CDR loss of lock alarm

  • Rx loss of signal alarm

  • Module not ready alarm

  • Tx CDR loss of lock alarm