ADMINISTRATION PORTAL
Help Center User GuideGetting StartedFAQsRelease Notes
 
X
User Guide
Getting Started
FAQs
Release Notes
Contents  

Selecting NAT Destination

The following procedures provides various methods that you can use to choose an endpoint as a NAT destination:

Adding an Endpoint as NAT Destination

Procedure

View and select the destination endpoint from the complete list of addresses, interfaces, services, zones, routing instances, or ports.

  1. Click the Destination field. A list of relevant endpoints are displayed.
  2. Click the View more results link provided at the bottom of the destination endpoints. The complete list of addresses, interfaces, services, zones, and routing instances, is displayed in the End Points panel on the right.
  3. (Optional) Click the edit icon to edit the address, service, or port endpoint.
  4. Click check mark icon () to select the endpoint as a destination.

Selecting Interfaces when GWR Resides Inside an NFX Box

The physical interfaces of an NFX box are mapped to the virtual interfaces of the Gateway Router (GWR) (vSRX) as given in Table 214. These are the default mappings provided by CSO. You may change these interface mappings based on your requirements.

Table 214: NFX and GWR Interface Mapping

NFX Physical Interface

GWR Virtual Interface

WAN 0 (ge-0/0/10)

ge-0/0/2

WAN 1 (ge-0/0/11)

ge-0/0/3

WAN 2 (xe-0/0/12)

ge-0/0/7

WAN 3 (xe-0/0/13)

ge-0/0/8

LAN-X (ge-0/0/X)

Ge-0/0/06.<vlan-id-for-X>

When you create a new NAT rule and an NFX physical interface is intended as the destination endpoint, select the respective mapped GWR interface.

Selecting NAT Destination Using Abbreviations

Enter an abbreviation in the Destination field to select the destination endpoint from a filtered list of destination endpoints.

Click the endpoints in the filtered list to select them.

Procedure

You can add a port number as a destination endpoint. To do so:

  1. Enter PORT or port in Destination.
  2. Press Tab.
  3. Enter the port number and press Enter.

    You can also enter a range of ports by using the separator -. For example, you can enter 10-20.

The entered port value is selected as a destination endpoint.

You can also select the endpoint from the complete list of addresses, interfaces, services, zones, and routing instances. See Adding an Endpoint as NAT Destination.

Selecting a NAT Destination from the End Points Panel

You can select a NAT destination endpoint from the End Points panel. Alternately, you can create a new NAT destination endpoint from the End Points panel, see Creating and Selecting a NAT Destination from the End Points Panel.

Procedure

To select a NAT destination endpoint from the End Points panel:

  1. Click the Destination field.
  2. Click the lesser-than icon (<) on the right.

    The End Points panel appears, displaying the list of available addresses, interfaces, services, zones, and routing instances.

  3. (Optional) To view more information about a destination endpoint, click the details icon on the right of the endpoint. To edit the destination endpoint, click the edit icon (pencil symbol) on the right of the endpoint.

    Note You can only edit or view details of a destination endpoint if these options appear on right side of the endpoint when you hover over it. Not all endpoints provide these options.

  4. Click the check mark icon () to add the endpoint as a destination.

Creating and Selecting a NAT Destination from the End Points Panel

Procedure

To create a new destination endpoint from the End Points panel:

  1. Click the add icon (+) on the top right of the panel and select the type of endpoint you want to create, among the options provided.

    Based on the option you select, the respective page appears. Fill in the required details to create a new endpoint.

    After the endpoint is created, it appears in the Endpoints panel.

  2. Click the check mark icon () to add the new endpoint as a destination.

Creating Addresses from Destination Field

You can use one of the following ways to create a new address from the Destination and use the newly created address as a destination endpoint:

Creating Services from Destination Field

Procedure

To create a new service from the Destination field and use the newly created service as a destination endpoint:

  1. In the Destination link, type svcs. The Add new service link appears at the bottom of the list of services.
  2. Click Add new service to create a new service.

    The Create Services page appears.

  3. Configure the new service. See Creating Services and Service Groups.
  4. Click Save to save the new service.

    The new service is created, and will be listed as an option for the destination. Select the new service to add it to the destination.

Related Documentation

Ask questions in TechWiki

Check documentation in TechLibrary

Rating by you:      
X

Additional Comments

800 characters remaining

May we contact you if necessary?

Name:
Email:

Need product assistance? Contact Juniper Support

Submit