Adding an On-Premise Spoke Site with Hybrid WAN Capability
You add an on-premise spoke site with Hybrid WAN capability from the Site page. The Hybrid WAN sites can have a maximum of two WAN links. You cannot apply intent policies for Hybrid WAN sites.
To add an on-premise spoke site with Hybrid WAN capability:
- Select Resources > Site Management .
The Sites page appears.
- Click Add and select Add On-Premise Spoke
The Add Site for Tenant-Name page appears.
- Complete the configuration settings in the General and WAN sections according to the guidelines provided in Table 1.
- Review the configuration and modify the settings, if needed, from the Summary tab.
- Click OK.
You are returned to the Sites page and a message indicating that the site creation job was triggered is displayed. You can click the job ID link to view the progress of the job. After the job is completed successfully, a confirmation message is displayed and the site that you added is displayed on the Sites page.
Table 1: Fields on the Add Spoke Site Page
Enter a site name. You can use any number of alphanumeric characters, including special characters. The maximum length is 10 characters.
Select a site group to which you want to assign the site.
Select Hybrid WAN to include Hybrid WAN capability in the on-premise spoke site.
This option is disabled for Hybrid WAN.
|Address and Contact Information|
Enter the street address of the site.
Enter the city where the site is located.
Enter the state or province where the site is located.
Enter the postal code for the locality of the site.
Select the country where the site is located.
Click the Validate button to verify the address.
Enter the name of a contact person for the site.
Enter the e-mail address of the contact person for the site.
Enter the phone number of the contact person for the site.
Name Server IP List
Specify one or more IPv4 addresses of the DNS server. To enter more than one DNS server address, type the address, press Enter, and then type the next address, and so on.
DNS servers are used to resolve hostnames into IP addresses.
Specify the fully qualified domain names (FQDNs) or IP addresses of one or more NTP servers.
The site must have DNS reachability to resolve the FQDN during site configuration.
Select the time zone of the site.
Select the device series to which the CPE belongs—SRX, NFX150, or NFX250.
Select a device template for the selected device series.
The device template contains information for configuring a device.
Select the device model for NFX150 device.
Enter the serial number of the CPE device.
The serial number is a 12-digit number present on the rear panel of the device. Serial numbers are case-sensitive.
Click the toggle button to enable or disable automatic activation of the CPE device.
When you enable this field, zero-touch provisioning (ZTP) of the CPE device is automatically triggered after the site is added to CSO.
The device template that you select determines whether this option is enabled or disabled by default.
Enter the activation code of the CPE device that your service provider supplied. If you do not want to specify an activation code, then disable the ACTIVATION_CODE_ENABLED field in the device template and save the changes.
Select the boot image from the drop-down list if you want to upgrade the image for the CPE device.
The boot image is the latest build image uploaded to the image management system. The boot image is used to upgrade the device when the CSO starts the ZTP process.
If the boot image is not provided, then the device skips the procedure to upgrade the device image. The boot image (NFX or SRX) is populated based on the device template that you have selected while creating a site. See Uploading a Device Image.
CPE AS Number
Specify the autonomous system(AS) number.
Specify the router name.
Router AS Number
Specify the AS number for the router.
OAM Traffic Information
Select this option if the management connectivity is initiated by Contrail Service Orchestration (CSO).
Enter an OAM VLAN ID for in-band management of the site. If you specify an OAM VLAN ID, then an in-band OAM traffic reaches the site through the selected OAM interface. The range is 0 through 65535.
Enter an IPv4 address prefix for the loopback interface on the CPE device. The IP address prefix must be a /32 IP address prefix and must be unique across the entire management network. If you do not specify an IPv4 address prefix, CSO automatically assigns the IP prefix from the reserved pool 100.124.0.0/14.
If you configured the address assignment method as STATIC, enter the IP address of the gateway of the WAN service provider.
Select whether the link would be an MPLS link or Internet link.
Specify the identifier for the Layer 2 VLAN for the CPE device.
Local IP Prefix
Enter the local IP address prefix of the WAN link.
Remote IP Prefix
Enter the remote IP address prefix of the WAN link.
Refer to the fields described for WAN_0 for an explanation of the fields.
Specify the name of the virtual routing and forwarding (VRF) instance.
Ipsec Concentrator Name
Specify the name of the IPsec concentrator device.
Internet Gateway IP
If you specified that the device is an IPsec concentrator, then specify the IPv4 address of the Internet gateway.