Help Center User GuideGetting StartedFAQ
 
X
User Guide
Getting Started
FAQ
Contents  

Adding Spoke Sites for Hybrid WAN Deployment

You add a spoke site from the Site page. This page describes how to create a spoke site for a tenant in hybrid WAN deployment.

Procedure

To add a spoke site:

  1. Select Sites > Site Management.

    The Sites page appears.

  2. Click Add and select Spoke Site.

    The Add Site for Tenant-Name page appears.

  3. Complete the configuration settings in the General and Connectivity Requirements section according to the guidelines provided in Table 169.

    Table 169: Fields on the Add Spoke Site Page

    Field

    Description

    General

    Site Name

    Enter a site name. You can use any number of alphanumeric characters, including special characters. The maximum length is 15 characters.

    Site Type

    Displays the site type. This field cannot be modified.

    Example: Spoke

    Tenant Topology

    Displays the topology of the tenant that was selected during the creation of the tenant. This field cannot be modified.

    Example: standalone

    Site Group

    Select a site group to which you want to assign the site.

    Example: hybridwan-spoke

    Address

    Street Address

    Enter the street address of the site.

    City

    Enter the city where the site is located.

    State/Province

    Enter the state or province where the site is located.

    ZIP/Postal Code

    Enter the postal code for the locality of the site.

    Country

    Select the country where the site is located. Click the Validate button to verify the address. The site address verification successful message is displayed if the address is correct. You can click the View location on a map link to see the address location. If you enter the wrong address and click the Validate button to verify the address, the Site address could not be validated message is displayed .

    Contact Information

    Contact Name

    Enter the name of a contact person for the site.

    Email

    Enter the e-mail ID of the contact person.

    Phone

    Enter the phone number of the contact person.

    Connectivity Requirements

    Click a connection plan to select the plan for WAN connectivity.

    A connection plan contains information prepopulated from the device template, and includes the device information, a list of supported features and the number of WAN links supported.

    Based on the connection plan, the following fields are populated:

    WAN Underlay Links

    WAN_0

    WAN_1

    Displays the WAN link. Depending on the connection plan selected, you can configure up to two WAN links per site that support the hybrid WAN. You can configure these links as MPLS or Internet links.

    Name

    Displays the name of the WAN link. This field cannot be modified.

    Type

    Displays the link type for WAN underlays. The default link types supported by the device templates are listed below:

    • NFX250 as Hybrid WAN CPE—Link type for WAN_0 is MPLS and WAN_1 is Internet.

    • NFX150 as Hybrid WAN CPE—Link type for WAN_0 is MPLS and WAN_1 is Internet.

    • SRX as Hybrid WAN CPE—Link type for WAN_0 is MPLS and WAN_1 is Internet.

    • SRX as Managed Internet CPE—Link type for WAN_0 is Internet.

    • NFX250 as Managed Internet CPE—Link type for WAN_0 is Internet.

    • NFX150 as Managed Internet CPE—Link type for WAN_0 is Internet.

    • NFX250 as Secure Internet CPE—Link type for WAN_0 is Internet.

    • NFX150 as Secure Internet CPE—Link type for WAN_0 is Internet.

  4. Review the configuration and modify the settings, if needed, from the Summary tab.
  5. Click OK.

    The newly added spoke site is displayed on the Sites page.

Related Documentation

Help us to improve. Rate this article.
Feedback Received. Thank You!

Ask questions in TechWiki

Check documentation in TechLibrary

Rating by you:      
X

Additional Comments

800 characters remaining

May we contact you if necessary?

Name:
Email:

Need product assistance? Contact Juniper Support

Submit