Help Center User GuideGetting StartedFAQ
User Guide
Getting Started

SLA Profiles and SD-WAN Policies Overview

Contrail Service Orchestration (CSO) enables you to create service-level agreement (SLA) profiles and map them to software-defined WAN (SD-WAN) policies for traffic management.

SLA Profiles

SLA profiles are created for applications or groups of applications for all tenants. An SLA profile consists of a set of configurable constraints that can be defined in the unified portal for both the Administration and Customer Portals. Table 116 lists the categories of configurable constraints that are defined in an SLA profile.

Table 116: SLA Profile Categories


Path preference and priority

Paths are the WAN links to be used for the SLA profile. You can select an MPLS or Internet link as the preferred path. For SLA profiles you must select a path preference or configure at least one SLA parameter. MPLS is more latency-sensitive than Internet.

You can define priority or precedence for the SLA profile. A value of one (1) indicates highest priority. SLA profiles with higher priorities are given precedence over SLA profiles with lower priorities. Priority is used when SLA requirements are not met on a WAN link and the site switches WAN links to meet the SLA requirements.

SLA parameters

You can also define one or more than one of the following SLA parameters:

  • Throughput—Amount of data (in Mbps) that is sent upstream and received downstream by the site during the selected time period

  • Latency—Amount of time (in ms) that a packet of data takes to travel from one designated point to another

  • Packet loss—Percentage of data packets dropped by the network to manage congestion

  • Jitter—Difference between the maximum and minimum round-trip times (in ms) of a packet of data

SLA parameters have precedence over path preference. Even if one SLA parameter is defined, then it is given a higher priority and will override the path preference. SD-WAN policies mapped to an SLA profile with defined SLA parameters are called dynamic policies. Dynamic policies applied to sites enable the site to override the path preference and switch WAN links when the preferred WAN link is not meeting SLA requirements as defined in the SLA parameters.

Class of service

Class of service (CoS) provides different levels of service assurances to various forms of traffic. CoS enables you to divide traffic into classes and offer an assured service level for each class. The classes of service listed in increasing order of priority and sensitivity to latency are best effort, voice, interactive video, streaming audio or video, control, and business essential. The default CoS is voice.

Rate limiters

Rate limiters are defined for traffic shaping and efficient bandwidth utilization. You can define the following rate limiters:

  • Maximum upstream and downstream rates—The maximum upstream and downstream rate for all applications associated with the SLA profile.

  • Maximum upstream and downstream burst sizes—The maximum size of a steady stream of traffic sent at average rates that exceed the upstream and downstream rate limits for short periods.

Note You must define at least one of the SLA parameters or path preference. You cannot leave both path preference and SLA parameters fields blank at the same time.

SD-WAN Policies

SD-WAN policy intents help in optimum utilization of the WAN links and efficient load distribution of traffic. SD-WAN policy intents are applied to source endpoints (such as sites and departments) and destination endpoints (applications or application groups) and can be defined for site-to-site traffic (by using SLA profiles) or for breakout traffic (by using breakout profiles).

Applications are classified into the following categories:

Policy intents consist of the following parameters:

SD-WAN supports advanced policy-based routing (APBR). APBR enables you to dynamically define the routing behavior of the SD-WAN network based on applications. Dynamic application-based routing makes it possible to define policies and to switch WAN links on the fly based on the application's defined SLA parameters. The APBR mechanism classifies sessions based on applications and application signatures and uses policy intents to identify the best possible route for the application. When the best possible route does not meet the application's defined SLA requirements, the SD-WAN network finds the next best possible route to meet SLA requirements.

For example, consider an application in a site. If you want the application group to use custom throughput, latency, or jitter, you can create an SLA profile with these custom values. You can then create an intent and configure the intent with the application and apply the custom SLA profile. When the intent is deployed, CSO determines the best suited WAN link to route traffic based in the application. If the WAN link fails to meet SLA requirements in runtime, the SD-WAN network switches WAN links to the next best suited path.

On the basis of the configured SLA profile constraints, you can categorize SD-WAN policies into two types:

Related Documentation

Ask questions in TechWiki

Check documentation in TechLibrary

Rating by you:      

Additional Comments

800 characters remaining

May we contact you if necessary?


Need product assistance? Contact Juniper Support