Selecting Firewall Destination

The following procedures provides various methods using which you can chose a firewall destination end point:

Adding an End Point as Firewall Destination

Procedure

1. Click on Destination. A list of relevant end points are displayed.
2. Click on View more results link provided at the bottom of the destination end points. The complete list of addresses, departments, sites, and site groups is displayed in the End Points panel on the right.
3. (Optional) Click the edit icon to edit the address, department, or site group end point. You cannot edit a site end point.
4. Click check mark icon (√) to select the end point as a destination.

Selecting Firewall Destination Using Abbreviations

Enter an abbreviation in the Destination field to select the destination end point from a filtered list of destination endpoints.

• To view a filtered list of addresses, enter ADDR or addr.
• To view a filtered list of addresses, enter APPS or apps.
• To view a filtered list of departments, enter DEPT or dept.
• To view a filtered list of services, enter SVCS or svcs.
• To view a filtered list of sites, enter SITE or site.
• To view a filtered list of site groups, enter STGP or stgp.

Click the endpoints in the filtered list to select them. You can also select the end point from the complete list of addresses, departments, sites, and site groups. See Adding an End Point as Firewall Destination.

Selecting a Firewall Destination from the End Points Panel

You can select a firewall destination end point from the End Points panel. Alternately, you can create a new firewall destination end point from the End Points panel, see Creating and Selecting a Firewall Destination from the End Points Panel.

Procedure

1. Click on the Destination field.
2. Click the lesser-than icon (<) on the right.

   The End Points panel appears, displaying the list of available addresses, departments, sites, and site groups.

3. (Optional) To view more information about a destination end point, click the details icon on the right of the end point. To edit the destination end point, click the edit icon (pencil symbol) on the right of the end point.

   Note: You can only edit or view details of a destination end point if these options appear on right side of the end point when you hover over it. Not all endpoints provide these options.

4. Click the check mark icon (√) to add the end point as a destination.

Creating and Selecting a Firewall Destination from the End Points Panel

Procedure

1. Click the add icon (+) on the top right of the panel and select the type of end point you want to create, among the options provided.

   Based on the option you select, the respective page appears. Fill in the required details to create a new end point.

   • To create a new address, see Creating Addresses or Address Groups.
   • To create a new department, seeCreating a Department.
   • To create a site or site group department, see Creating Site Groups.

   After the end point is created, it appears in the Endpoints panel.

2. Click the check mark icon (√) to add the new end point as a destination.

Creating Addresses from Destination

You can use one of the following ways to create a new address from the Destination and use the newly created address as a destination end point:

• Type the address directly in the Destination field. If the address is valid, it is created immediately and added as a destination end point.
• Create an address from the Destination field, using the following steps:

  Procedure

  1. In the Destination field, type addr. The Add new address link appears at the bottom of the list of addresses.
  2. Click Add new address to create a new address.

     The Create Addresses page appears.

  3. Configure the new address. See Creating Addresses or Address Groups.
  4. Click Save to save the new address.

     The new address is created, and will be listed as an option for the destination. Select the new address to add it to the destination.

Creating Departments from Destination

Create a new department from the Destination field and use the newly created department as a destination end point:

Procedure

1. In Destination, type dept. The link Add new department appears at the bottom of the list of departments.
2. Click on Add new department, to create a new department.

   The Create Department page appears.

3. Configure the new department. See Creating a Department.
4. Click Save to save the new department.

   The new department is created, and will be listed as an option for the destination. Select the new department to add it to the destination.

Related Documentation

• Creating Firewall Policy Intents
• Firewall Policy Overview
• About the Firewall Policy Page
• Editing, Cloning, and Deleting Firewall Policy Intents