Managing Information for a Network Element
Use this procedure to view or update system-related information for an individual network element.
- Right-click a network element in the Network tree or in
the Topology Map view, and then select System Info.
The System Info tab appears.
- Click one of the following tabs to view or change information
for the selected topic.
System
Management
SNMP
Time/Date/NTP
Craft Eth/Serial
Note Depending on the network element type, some fields can be edited, some cannot be edited, and some do not apply to that type. The information that cannot be edited, or that is not applicable, is greyed out.
Table 1: System Info Tab for BTI7000 Series NE
Panel Name
Description
Parameters
System
Provides access to general information.
System Settings
Name
Location
Uptime - not editable
Vendor - not editable
Model - not editable
Active SW Version - not editable
Inactive SW Version - not editable
Serial Number - not editable
Element Number
Site Number
Contact
System Wide Settings
Auto-Provisioning Mode - this is the AINS mode
Auto-In Service Timer
Auto Deprovisioning Timer - not applicable for NEs running release 8.2 and higher
Filler Plate Detection
Customer Logging Facility ID
Management
Provides access to management information.
Note: When Management information for an NE is modified, the NE is deleted from PSM and rediscovered using the updated settings.
Management Settings
Outband IP Address
Outband IP Mask
System Gateway
Mac Address - not editable
OSC Settings
Enable OSC 1 Port
Enable OSC 2 Port
Secondary Gateway
OSPF Management: OSPF
Router ID
Route Redistribution
Area ID
State
Delete OSPF
Add OSPF
OSPF Management: OSPF Interfaces
This is the list of OSPF interfaces configured on the network element.
Add, edit, or delete interfaces as desired.
OSPF Management: LSDB
This is the link state database. It is read-only.
OSPF Management: Neighbors
This is the list of OSPF neighbors. It is read-only.
Note: For more information on provisioning OSPF, see Provisioning OSPF on a BTI7000 Series Management Network
SNMP
Provides access to read-only community and trap receiver information.
Communities
Private - not editable
Public - not editable
Trap Receivers
Trap Receivers - not editable
IP Address - not editable
Community - not editable
Version - not editable
Port - not editable
Notification - not editable
Time/Date/NTP
Provides access to time, date, and NTP (Network Timing Protocol) settings.
Time and Date Settings
Adjust time for daylight savings changes
Time
Time Zone
Date
NTP Settings
Poll Period
Authorization Key (0 to 65535)
Sync State - not editable
Stratum - not editable
Reference IP - not editable
NTP Associations (NTP Client IP addresses)
Craft Eth/Serial
Provides access to Craft Ethernet and Craft Serial information.
Craft Serial Settings
Baud Rate
Data Bits
Parity
Stop Bits
Craft Ethernet Settings
Craft IP Address
Craft Mask
Media Rate - not editable
Custom
Craft MAC Address - not editable
Broadcast Address - not editable
Interface Speed - not editable
MTU Size - not editable
Table 2: System Info Tab for BTI7800 Series NE
Panel Name
Description
Parameters
System
Provides access to general information.
System Settings
Name
Location
Uptime - not editable
Vendor - not editable
Model - not editable
Active SW Version - not editable
Inactive SW Version - not applicable
Serial Number - not applicable
Element Number - not applicable
Site Number - not applicable
Contact
System Wide Settings
Auto-Provisioning Mode - this is the AINS mode
Auto-In Service Timer
Auto Deprovisioning Timer - not applicable
Filler Plate Detection - not applicable
Customer Logging Facility ID
Management
Provides access to management information.
Note: When Management information for an NE is modified, the NE is deleted from PSM and rediscovered using the updated settings.
Management Settings
The following are the out-of-band management settings:
Outband IP Address - not editable
Outband IP Mask - not editable
System Gateway - not editable
Mac Address - not applicable
In-band Management Settings
This panel displays the in-band management interfaces.
Add or delete interfaces as desired.
Proxy ARP
IS-IS and NET
Note: For more information on provisioning in-band management, see Configuring In-Band Management on a BTI7800 Network Element
SNMP
Provides access to read-only community and trap receiver information.
Communities
Private - not editable
Public - not editable
Trap Receivers
Trap Receivers - not editable
IP Address - not editable
Community - not editable
Version - not editable
Port - not editable
Notification - not editable
Time/Date/NTP
Provides access to time, date, and NTP (Network Timing Protocol) settings.
Time and Date Settings
Adjust time for daylight savings changes - not editable
Time - not editable
Time Zone - not editable
Date - not editable
NTP Settings
NTP Status - not editable
NTP Servers - not editable
Table 3: System Info Tab for BTI800 Series NE
Panel Name
Description
Parameters
System
Provides access to general information.
System Settings
Name
Location
Uptime - not editable
Vendor - not editable
Model - not editable
Active SW Version - not editable
Inactive SW Version - not applicable
Serial Number - not applicable
Element Number - not applicable
Site Number - not applicable
Contact
System Wide Settings - not applicable
Management
Provides read-only access to management information.
Management Settings
Outband IP Address - not editable
Outband IP Mask - not editable
System Gateway - not editable
Mac Address - not editable
In-band Settings
IP Address - not editable
IP Mask - not editable
Outer VLAN Name - not editable
Inner VLAN Name - not editable
Network Address - not editable
Mac Address - not editable
Outer VLAN Id (Priority) - not editable
Inner VLAN Id (Priority) - not editable
SNMP
Provides access to read-only community and trap receiver information.
Communities
Private - not editable
Public - not editable
Trap Receivers
Trap Receivers - not editable
IP Address - not editable
Community - not editable
Port - not editable
Time/Date/NTP
Provides access to time and date settings.
Time and Date Settings
Time
Time Zone
Date
NTP Settings
Note: You must disable NTP on the BTI810 prior to making any changes.
Note: NTP is always enabled on the BTI805, BTI821, and BTI822 devices.
Poll Period - read-only for the BTI805, BTI821, and BTI822.
Status - read-only for the BTI805, BTI821, and BTI822.
Preferred Server
Server1 IP Address
Server2 IP Address
Server3 IP Address
Craft Eth/Serial
Provides read-only access to Craft Serial information.
Craft Serial Settings
Baud Rate - not editable
Data Bits - not editable
Parity - not editable
Stop Bits - not editable
Table 4: System Info Tab for MX Series and PTX Series Routers and QFX Series Switches
Panel Name
Description
Parameters
System
Provides access to general information.
System Settings
Name
Location
Uptime - not applicable
Vendor - not applicable
Model - not applicable
Active SW Version - not applicable
Inactive SW Version - not applicable
Serial Number - not applicable
Element Number - not applicable
Site Number - not applicable
Contact
Management
Not supported.
SNMP
Not supported.
Time/Date/NTP
Not supported.
Craft Eth/Serial
Not supported.
Table 5: System Info Tab for BTI700 Series NE
Panel Name
Description
Parameters
System
Provides access to general information.
System Settings
Name
Location
Uptime - not editable
Vendor - not editable
Model - not editable
Active SW Version - not editable
Inactive SW Version - not applicable
Model - not editable
Serial Number - not editable
Element Number - not applicable
Site Number - not applicable
Contact
System Wide Settings - not applicable
Management
Provides read-only access to management information.
Management Settings
Outband IP Address - not editable
Outband IP Mask - not editable
System Gateway - not editable
Mac Address - not editable
SNMP
Provides access to read-only community and trap receiver information.
Communities
Private - not editable
Public - not editable
Trap Receivers
Trap Receivers - not editable
IP Address - not editable
Community - not editable
Version - not editable
Port - not editable
Notification - not applicable
Time/Date/NTP
Provides access to time, date, and NTP (Network Timing Protocol) settings.
Time and Date Settings
Adjust time for daylight savings changes - not applicable
Time
Time Offset - not editable
Date
NTP Settings (BTI700 Series except for BTI718E)
NTP VLANs - with Mode set to Client
Mode set to Client
NTP Server IP
Static IP Address in CIDR notation (e.g. 10.0.0.1/24)
Time Flag
Time Offset
Non NTP VLANs - with Mode set to None
Mode set to None
NTP Server IP - not applicable
Static IP Address in CIDR notation (e.g. 10.0.0.1/24)
Time Flag - not applicable
Time Offset - not applicable
NTP Settings (BTI718E)
Sntp Master - not editable
Sntp Stratum - not editable
Sntp Server Send Interval - enter the power (of 2) seconds (e.g. enter 4 for 24 seconds)
Sntp Client Send Interval - enter the power (of 2) seconds
Peer - can add or delete a peer; cannot edit an existing peer
Peer Work Mode - not editable
Peer IP - specify for a new peer; not editable for an existing peer
Peer SNTP Version - not editable
Peer ReceivedTime - not editable
Table 6: System Info Tab for OPS, EDFA, and RAMAN Devices
Panel Name
Description
Parameters
System
Provides access to general information.
System Settings
Name
Location
Uptime - not editable
Vendor - not editable
Model - not editable
Active SW Version - not editable
Inactive SW Version - not applicable
Model - not editable
Serial Number - not editable
Element Number - not applicable
Site Number - not applicable
Contact
System Wide Settings - not applicable
Management
Provides read-only access to management information.
Management Settings
Outband IP Address - not editable
Outband IP Mask - not editable
System Gateway - not editable
Mac Address - not editable
SNMP
Provides read-only access to community and trap receiver information.
Communities - not editable
Trap Receivers - not editable
Time/Date/NTP
Provides read-only access to time and date settings.
Time and Date Settings - not editable
Table 7: System Info Tab for PSM Server
Panel Name
Description
Parameters
System
Provides access to general information.
System Settings
Name - not editable
Location - not editable
Uptime - not editable
Vendor - not editable
Model - not editable
Active SW Version - not editable
Element Number - not editable
Site Number - not editable
Contact - not editable
Management
Provides read-only access to IP information.
Management Settings
Outband IP Address - not editable
Outband IP Mask - not editable
System Gateway - not editable
Mac Address - not editable
SNMP
Not supported.
Time/Date/NTP
Not supported.
Craft Eth/Serial
Not supported.
- Click Apply Changes to save the settings or Discard Edits to revert to the previous settings.