Managing Information for a Network Element

Use this procedure to view or update system-related information for an individual network element.

1. Right-click a network element in the Network tree or in the Topology Map view, and then select System Info.

   The System Info tab appears.

   

2. Click one of the following tabs to view or change information for the selected topic.
   • System
   • Management
   • SNMP
   • Time/Date/NTP
   • Craft Eth/Serial

   Note: Depending on the network element type, some fields can be edited, some cannot be edited, and some do not apply to that type. The information that cannot be edited, or that is not applicable, is greyed out.

   Table 1: System Info Tab for BTI7000 Series NE

   Panel Name	Description	Parameters
   System	Provides access to general information.	System Settings Name Location Uptime - not editable Vendor - not editable Model - not editable Active SW Version - not editable Inactive SW Version - not editable Serial Number - not editable Element Number Site Number Contact System Wide Settings Auto-Provisioning Mode - this is the AINS mode Auto-In Service Timer Auto Deprovisioning Timer - not applicable for NEs running release 8.2 and higher Filler Plate Detection Customer Logging Facility ID
   Management	Provides access to management information. Note: When Management information for an NE is modified, the NE is deleted from PSM and rediscovered using the updated settings.	Management Settings Outband IP Address Outband IP Mask System Gateway Mac Address - not editable OSC Settings Enable OSC 1 Port Enable OSC 2 Port Secondary Gateway OSPF Management: OSPF Router ID Route Redistribution Area ID State Delete OSPF Add OSPF OSPF Management: OSPF Interfaces This is the list of OSPF interfaces configured on the network element. Add, edit, or delete interfaces as desired. OSPF Management: LSDB This is the link state database. It is read-only. OSPF Management: Neighbors This is the list of OSPF neighbors. It is read-only. Note: For more information on provisioning OSPF, see Provisioning OSPF on a BTI7000 Series Management Network
   SNMP	Provides access to read-only community and trap receiver information.	Communities Private - not editable Public - not editable Trap Receivers Trap Receivers - not editable IP Address - not editable Community - not editable Version - not editable Port - not editable Notification - not editable
   Time/Date/NTP	Provides access to time, date, and NTP (Network Timing Protocol) settings.	Time and Date Settings Adjust time for daylight savings changes Time Time Zone Date NTP Settings Poll Period Authorization Key (0 to 65535) Sync State - not editable Stratum - not editable Reference IP - not editable NTP Associations (NTP Client IP addresses)
   Craft Eth/Serial	Provides access to Craft Ethernet and Craft Serial information.	Craft Serial Settings Baud Rate Data Bits Parity Stop Bits Craft Ethernet Settings Craft IP Address Craft Mask Media Rate - not editable Custom Craft MAC Address - not editable Broadcast Address - not editable Interface Speed - not editable MTU Size - not editable

   Table 2: System Info Tab for BTI7800 Series NE

   Panel Name	Description	Parameters
   System	Provides access to general information.	System Settings Name Location Uptime - not editable Vendor - not editable Model - not editable Active SW Version - not editable Inactive SW Version - not applicable Serial Number - not applicable Element Number - not applicable Site Number - not applicable Contact System Wide Settings Auto-Provisioning Mode - this is the AINS mode Auto-In Service Timer Auto Deprovisioning Timer - not applicable Filler Plate Detection - not applicable Customer Logging Facility ID
   Management	Provides access to management information. Note: When Management information for an NE is modified, the NE is deleted from PSM and rediscovered using the updated settings.	Management Settings The following are the out-of-band management settings: Outband IP Address - not editable Outband IP Mask - not editable System Gateway - not editable Mac Address - not applicable In-band Management Settings This panel displays the in-band management interfaces. Add or delete interfaces as desired. Proxy ARP IS-IS and NET Note: For more information on provisioning in-band management, see Configuring In-Band Management on a BTI7800 Network Element
   SNMP	Provides access to read-only community and trap receiver information.	Communities Private - not editable Public - not editable Trap Receivers Trap Receivers - not editable IP Address - not editable Community - not editable Version - not editable Port - not editable Notification - not editable
   Time/Date/NTP	Provides access to time, date, and NTP (Network Timing Protocol) settings.	Time and Date Settings Adjust time for daylight savings changes - not editable Time - not editable Time Zone - not editable Date - not editable NTP Settings NTP Status - not editable NTP Servers - not editable

   Table 3: System Info Tab for BTI800 Series NE

   Panel Name	Description	Parameters
   System	Provides access to general information.	System Settings Name Location Uptime - not editable Vendor - not editable Model - not editable Active SW Version - not editable Inactive SW Version - not applicable Serial Number - not applicable Element Number - not applicable Site Number - not applicable Contact System Wide Settings - not applicable
   Management	Provides read-only access to management information.	Management Settings Outband IP Address - not editable Outband IP Mask - not editable System Gateway - not editable Mac Address - not editable In-band Settings IP Address - not editable IP Mask - not editable Outer VLAN Name - not editable Inner VLAN Name - not editable Network Address - not editable Mac Address - not editable Outer VLAN Id (Priority) - not editable Inner VLAN Id (Priority) - not editable
   SNMP	Provides access to read-only community and trap receiver information.	Communities Private - not editable Public - not editable Trap Receivers Trap Receivers - not editable IP Address - not editable Community - not editable Port - not editable
   Time/Date/NTP	Provides access to time and date settings.	Time and Date Settings Time Time Zone Date NTP Settings Note: You must disable NTP on the BTI810 prior to making any changes. Note: NTP is always enabled on the BTI805, BTI821, and BTI822 devices. Poll Period - read-only for the BTI805, BTI821, and BTI822. Status - read-only for the BTI805, BTI821, and BTI822. Preferred Server Server1 IP Address Server2 IP Address Server3 IP Address
   Craft Eth/Serial	Provides read-only access to Craft Serial information.	Craft Serial Settings Baud Rate - not editable Data Bits - not editable Parity - not editable Stop Bits - not editable

   Table 4: System Info Tab for MX Series and PTX Series Routers and QFX Series Switches

   Panel Name	Description	Parameters
   System	Provides access to general information.	System Settings Name Location Uptime - not applicable Vendor - not applicable Model - not applicable Active SW Version - not applicable Inactive SW Version - not applicable Serial Number - not applicable Element Number - not applicable Site Number - not applicable Contact
   Management	Not supported.
   SNMP	Not supported.
   Time/Date/NTP	Not supported.
   Craft Eth/Serial	Not supported.

   Table 5: System Info Tab for BTI700 Series NE

   Panel Name	Description	Parameters
   System	Provides access to general information.	System Settings Name Location Uptime - not editable Vendor - not editable Model - not editable Active SW Version - not editable Inactive SW Version - not applicable Model - not editable Serial Number - not editable Element Number - not applicable Site Number - not applicable Contact System Wide Settings - not applicable
   Management	Provides read-only access to management information.	Management Settings Outband IP Address - not editable Outband IP Mask - not editable System Gateway - not editable Mac Address - not editable
   SNMP	Provides access to read-only community and trap receiver information.	Communities Private - not editable Public - not editable Trap Receivers Trap Receivers - not editable IP Address - not editable Community - not editable Version - not editable Port - not editable Notification - not applicable
   Time/Date/NTP	Provides access to time, date, and NTP (Network Timing Protocol) settings.	Time and Date Settings Adjust time for daylight savings changes - not applicable Time Time Offset - not editable Date NTP Settings (BTI700 Series except for BTI718E) NTP VLANs - with Mode set to Client Mode set to Client NTP Server IP Static IP Address in CIDR notation (e.g. 10.0.0.1/24) Time Flag Time Offset Non NTP VLANs - with Mode set to None Mode set to None NTP Server IP - not applicable Static IP Address in CIDR notation (e.g. 10.0.0.1/24) Time Flag - not applicable Time Offset - not applicable NTP Settings (BTI718E) Sntp Master - not editable Sntp Stratum - not editable Sntp Server Send Interval - enter the power (of 2) seconds (e.g. enter 4 for 24 seconds) Sntp Client Send Interval - enter the power (of 2) seconds Peer - can add or delete a peer; cannot edit an existing peer Peer Work Mode - not editable Peer IP - specify for a new peer; not editable for an existing peer Peer SNTP Version - not editable Peer ReceivedTime - not editable

   Table 6: System Info Tab for OPS, EDFA, and RAMAN Devices

   Panel Name	Description	Parameters
   System	Provides access to general information.	System Settings Name Location Uptime - not editable Vendor - not editable Model - not editable Active SW Version - not editable Inactive SW Version - not applicable Model - not editable Serial Number - not editable Element Number - not applicable Site Number - not applicable Contact System Wide Settings - not applicable
   Management	Provides read-only access to management information.	Management Settings Outband IP Address - not editable Outband IP Mask - not editable System Gateway - not editable Mac Address - not editable
   SNMP	Provides read-only access to community and trap receiver information.	Communities - not editable Trap Receivers - not editable
   Time/Date/NTP	Provides read-only access to time and date settings.	Time and Date Settings - not editable

   Table 7: System Info Tab for PSM Server

   Panel Name	Description	Parameters
   System	Provides access to general information.	System Settings Name - not editable Location - not editable Uptime - not editable Vendor - not editable Model - not editable Active SW Version - not editable Element Number - not editable Site Number - not editable Contact - not editable
   Management	Provides read-only access to IP information.	Management Settings Outband IP Address - not editable Outband IP Mask - not editable System Gateway - not editable Mac Address - not editable
   SNMP	Not supported.
   Time/Date/NTP	Not supported.
   Craft Eth/Serial	Not supported.

3. Click Apply Changes to save the settings or Discard Edits to revert to the previous settings.