Beispiel: VPLS-Konfiguration (BGP-Signaling)
In Abbildung 1 ist eine einfache VPLS-Topologie zwischen den Routern PE1 und PE2 aktiviert. CE-Router CE1 und CE2 verwenden Ethernet-basierte Schnittstellen, um VLAN 600 mit ihrem lokalen PE-Router zu verbinden. Die PE-Router PE1 und PE2 sind durch LSPs miteinander verbunden, die über ein Service Provider-Backbone mit MPLS, BGP, RSVP und OSPF aktiviert sind.
In einer VPLS-Routing-Instanz namens greenPE1 verfügt über eine lokale Schnittstelle fe-0/1/0 und einen virtuellen Port von vt-0/3/0.32770 (der virtuelle Port wird dynamisch auf dem Tunnel Services PIC erstellt, wenn VPLS konfiguriert ist). PE2 verfügt über eine lokale Schnittstelle fe-0/1/0 und einen virtuellen Port von vt-0/3/0.32771 in derselben green Instanz. Infolgedessen senden die Router CE1 und CE2 Ethernet-Datenverkehr aneinander, als ob sie physisch in einem LAN miteinander verbunden wären.
Auf Router CE1 müssen Sie nur die Fast-Ethernet-Schnittstelle konfigurieren, die mit PE1 verbunden wird. Achten Sie darauf, die VLAN-Kennung und die IP-Adresse aufzuschreiben, damit Sie sie später am CE2 abgleichen können.
Router CE1
[edit]
interfaces {
fe-0/1/0 {
vlan-tagging; # Configure VLAN tagging for VLAN VPLS or extended VLAN VPLS.
unit 0 {
vlan-id 600; # The Ethernet interface on CE2 must use the same VLAN ID.
family inet {
address 10.11.3.1/24; # The interface on CE2 must use the same prefix.
}
}
}
}
Wenn Router PE1 ein Gerät der MX-Serie ist, müssen Sie eine Tunnelserviceschnittstelle konfigurieren.
Um Tunnelschnittstellen auf einem Router der MX-Serie zu erstellen, fügen Sie die tunnel-services Anweisung auf der Hierarchieebene [edit chassis fpc slot-number pic number] ein. Um die Bandbreite für eine Tunnelschnittstelle zu konfigurieren, fügen Sie die bandwidth Anweisung auf der Hierarchieebene [edit chassis fpc slot-number pic number tunnel services] ein.
Das folgende Beispiel zeigt eine Tunnelschnittstelle mit einer Bandbreite von 1 Gbit/s, die auf PFE 3 der in Steckplatz 0 eines Routers der MX-Serie installierten DPC konfiguriert ist:
[edit chassis]
fpc 0 {
pic 3 {
tunnel services {
bandwidth 1g;
}
}
}
Bereiten Sie den Router auf Router PE1 auf VPLS vor, indem Sie BGP, MPLS, OSPF und RSVP konfigurieren. (Diese Protokolle sind die Grundlage für die meisten Layer-2-VPN-bezogenen Anwendungen, einschließlich VPLS.) Fügen Sie die signaling Anweisung auf Hierarchieebene [edit protocols bgp group group-name family l2vpn] ein, da VPLS dieselbe Infrastruktur für interne BGP wie Layer-2-VPNs verwendet.
In Junos OS Version 7.3 und höher ersetzt die signaling Anweisung die unicast Anweisung auf [edit protocols bgp group group-name family l2vpn] Hierarchieebene. Sie müssen die signaling Anweisung verwenden, wenn Sie VPLS-Domänen und Layer-2-VPNs gleichzeitig konfigurieren möchten.
Konfigurieren Sie als Nächstes die VLAN-Tagging auf der Fast-Ethernet-Schnittstelle, die mit Dem Router CE1 verbunden ist. Schließen Sie die VLAN-VPLS-Kapselung sowohl auf physischer als auch auf logischer Schnittstellenebene ein. Achten Sie darauf, dieselbe VLAN-ID für alle Ethernet-Schnittstellen zu verwenden, die Teil einer einzelnen VPLS-Instanz sind. Fügen Sie schließlich die Fast-Ethernet-Schnittstelle einer VPLS-Routing-Instanz hinzu und geben Sie den Standortbereich, die Standort-ID-Nummer und den Standortnamen an.
Router PE1
[edit]
interfaces {
fe-0/1/0 {
vlan-tagging;# Configure VLAN tagging for VLAN VPLS or extended VLAN VPLS.
encapsulation vlan-vpls; # Configure VPLS encapsulation on both the
unit 0 { # physical interface and the logical interface.
encapsulation vlan-vpls;
vlan-id 600;# The VLAN ID is the same one used by the CE routers.
}
}
so-1/1/0 {
unit 0 {
family inet {
address 10.11.1.5/30;
}
family mpls;
}
}
lo0 {
unit 0 {
family inet {
address 10.245.14.218/32;
}
}
}
}
routing-options {
autonomous-system 69;
forwarding-table {
export exp-to-fwd; # Apply a policy that selects an LSP for the VPLS instance.
}
}
protocols {
rsvp {
interface all {
aggregate;
}
}
mpls {
label-switched-path pe1-to-pe2 { # Configure an LSP to reach other VPLS PEs.
to 10.245.14.219;
}
interface all;
}
bgp {
group vpls-pe {
type internal;
local-address 10.245.14.218;
family l2vpn { # VPLS uses the same infrastructure as Layer 2 VPNs
signaling; # for internal BGP.
}
neighbor 10.245.14.217;
neighbor 10.245.14.219;
}
}
ospf {
traffic-engineering;
area 0.0.0.0 {
interface so-1/1/0.0 {
metric 11;
}
interface lo0.0 {
passive;
}
}
}
}
policy-options {
policy-statement exp-to-fwd {
term a {
from community grn-com; # Matches the community in the VPLS instance.
then {
install-nexthop lsp pe1-to-pe2; # If there are multiple LSPs that exist
accept; # between VPLS PE routers, this statement sends VPLS traffic
} # over a specific LSP.
}
}
community grn-com members target:11111:1; # Adds the instance to a BGP
} # community.
routing-instances {
green {
instance-type vpls; # Configure a VPLS routing instance.
interface fe-0/1/0.0;
route-distinguisher 10.245.14.218:1;
vrf-target target:11111:1; # This value is important to the BGP community.
protocols {
vpls { # Configure a VPLS site range, site name, and site identifier.
site-range 10;
site greenPE1 {
site-identifier 1;
}
}
}
}
}
Konfigurieren Sie auf Router P0 BGP, MPLS, OSPF und RSVP zur Verbindung von PE1 und PE2.
Router P0
[edit]
interfaces {
so-0/0/0 {
unit 0 {
family inet {
address 10.11.2.6/30;
}
family mpls;
}
}
so-1/1/0 {
unit 0 {
family inet {
address 10.11.1.6/30;
}
family mpls;
}
}
lo0 {
unit 0 {
family inet {
address 10.245.14.217/32;
}
}
}
}
routing-options {
autonomous-system 69;
}
protocols {
rsvp {
interface all {
aggregate;
}
}
mpls {
interface all;
}
bgp {
group vpls-pe {
type internal;
local-address 10.245.14.217;
family l2vpn { # VPLS uses the same infrastructure as Layer 2 VPNs
signaling; # for internal BGP.
}
neighbor 10.245.14.218;
neighbor 10.245.14.219;
}
}
ospf {
traffic-engineering;
area 0.0.0.0 {
interface so-1/1/0.0 {
metric 11;
}
interface so-0/0/0.0 {
metric 15;
}
interface lo0.0 {
passive;
}
}
}
}
Wenn es sich bei Router PE2 um ein Gerät der MX-Serie handelt, müssen Sie eine Tunnelserviceschnittstelle konfigurieren.
Um Tunnelschnittstellen auf einem Router der MX-Serie zu erstellen, fügen Sie die tunnel-services Anweisung auf der Hierarchieebene [edit chassis fpc slot-number pic number] ein. Um die Bandbreite für eine Tunnelschnittstelle zu konfigurieren, fügen Sie die bandwidth Anweisung auf der Hierarchieebene [edit chassis fpc slot-number pic number] ein.
Das folgende Beispiel zeigt eine Tunnelschnittstelle mit einer Bandbreite von 1 Gbit/s, die auf PFE 3 der in Steckplatz 0 eines Routers der MX-Serie installierten DPC konfiguriert ist:
[edit chassis]
fpc 0 {
pic 3 {
tunnel services {
bandwidth 1g;
}
}
}
Konfigurieren Sie auf Router PE2 BGP, MPLS, OSPF und RSVP, um die Konfiguration auf PE1 zu ergänzen. Konfigurieren Sie als Nächstes VLAN-Tagging auf der Fast Ethernet-Schnittstelle, die mit Router CE2 verbunden ist. Schließen Sie die VLAN-VPLS-Kapselung sowohl auf physischer als auch auf logischer Schnittstellenebene ein. Achten Sie darauf, dieselbe VLAN-ID für alle Ethernet-Schnittstellen zu verwenden, die Teil einer einzelnen VPLS-Instanz sind. Fügen Sie schließlich die Fast-Ethernet-Schnittstelle einer VPLS-Routing-Instanz hinzu und geben Sie den Standortbereich, die Standort-ID-Nummer und den Standortnamen an.
Router PE2
[edit]
interfaces {
fe-0/1/0 {
vlan-tagging; # Configure VLAN tagging for VLAN VPLS or extended VLAN VPLS.
encapsulation vlan-vpls; # Configure VPLS encapsulation on both the
unit 0 { # physical interface and logical interface.
encapsulation vlan-vpls;
vlan-id 600;# The VLAN ID is the same one used by the CE routers.
}
}
so-0/0/0 {
unit 0 {
family inet {
address 10.11.2.5/30;
}
family mpls;
}
}
lo0 {
unit 0 {
family inet {
address 10.245.14.219/32;
}
}
}
}
routing-options {
autonomous-system 69;
forwarding-table {
export exp-to-fwd; # Apply a policy that selects an LSP for the VPLS instance.
}
}
protocols {
rsvp {
interface all {
aggregate;
}
}
mpls {
label-switched-path pe2-to-pe1 { # Configure an LSP to other VPLS PE routers.
to 10.245.14.218;
}
interface all;
}
bgp {
group vpls-pe {
type internal;
local-address 10.245.14.219;
family l2vpn { # VPLS uses the same infrastructure as Layer 2 VPNs
signaling; # for internal BGP.
}
neighbor 10.245.14.217;
neighbor 10.245.14.218;
}
}
ospf {
traffic-engineering;
area 0.0.0.0 {
interface so-0/0/0.0 {
metric 15;
}
interface lo0.0 {
passive;
}
}
}
}
policy-options {
policy-statement exp-to-fwd {
term a {
from community grn-com; # Matches the community with the VPLS instance.
then {
install-nexthop lsp pe2-to-pe1; # If there are multiple LSPs that exist
accept; # between VPLS PE routers, this statement sends VPLS traffic
} # over a specific LSP.
}
}
community grn-com members target:11111:1; # This adds the instance into a BGP community.
}
routing-instances {
green {
instance-type vpls; # Configure a VPLS routing instance.
interface fe-0/1/0.0;
route-distinguisher 10.245.14.219:1;
vrf-target target:11111:1; # This value is important for the BGP community.
protocols {
vpls { # Configure a VPLS site range, site name, and site identifier.
site-range 10;
site greenPE2 {
site-identifier 2;
}
}
}
}
}
Vervollständigen Sie auf dem Router CE2 Ihr VPLS-Netzwerk, indem Sie die Fast-Ethernet-Schnittstelle konfigurieren, die mit PE2 verbunden wird. Verwenden Sie dieselbe VLAN-Kennung und dasselbe IP-Adresspräfix, das auch auf Router CE1 verwendet wird.
Router CE2
[edit]
interfaces {
fe-0/1/0 {
vlan-tagging; # Configure VLAN tagging for VLAN VPLS or extended VLAN VPLS.
unit 0 {
vlan-id 600; # The Ethernet interface on CE1 must use the same VLAN ID.
family inet {
address 10.11.3.2/24; # The interface on CE1 must use the same prefix.
}
}
}
}
Ihre Arbeit verifizieren
Verwenden Sie die folgenden Befehle, um die ordnungsgemäße Funktion von VPLS zu überprüfen:
clear vpls mac-address instance instance-nameshow interfaces terseshow route forwarding-table family mplsshow route forwarding-table family vpls (destination | extensive | matching | table)show route instance (detail)show system statistics vplsshow vpls connectionsshow vpls statistics
Der folgende Abschnitt zeigt die Ausgabe dieser Befehle auf Router PE1 als Ergebnis des Konfigurationsbeispiels:
user@PE1> show interfaces terse
Interface Admin Link Proto Local Remote
so-1/1/0 up up
so-1/1/0.0 up up inet 10.11.1.5/30
mpls
so-1/1/1 up up
so-1/1/2 up up
so-1/1/3 up up
fe-0/1/0 up up
fe-0/1/0.0 up up vpls # This is the local Fast Ethernet
# interface.
fe-0/1/1 up up
fe-0/1/2 up up
fe-0/1/3 up up
gr-0/3/0 up up
ip-0/3/0 up up
mt-0/3/0 up up
pd-0/3/0 up up
pe-0/3/0 up up
vt-0/3/0 up up
vt-0/3/0.32770 up up # This is the dynamically generated virtual port.
dsc up up
fxp0 up up
fxp0.0 up up inet 192.186.14.218/24
fxp1 up up
fxp1.0 up up tnp 4
gre up up
ipip up up
lo0 up up
lo0.0 up up inet 10.245.14.218 --> 0/0
127.0.0.1 --> 0/0
inet6 fe80::2a0:a5ff:fe28:13e0
feee::10:245:14:218
lsi up up
mtun up up
pimd up up
pime up up
tap up up
user@PE1> show system statistics vpls
vpls:
0 total packets received
0 with size smaller than minimum
0 with incorrect version number
0 packets for this host
0 packets with no logical interface
0 packets with no family
0 packets with no route table
0 packets with no auxiliary table
0 packets with no corefacing entry
0 packets with no CE-facing entry
6 mac route learning requests # This indicates that VPLS is working.
6 mac routes learnt
0 mac routes aged
0 mac routes moved
Um VPLS-Quell- und Ziel-MAC-Adressen-Buchhaltungsinformationen anzuzeigen, verwenden Sie die destination, extensive, matchingoder table Option mit dem show route forwarding-table family vpls Befehl. Beachten Sie bei der Analyse der Anzeigeausgaben Folgendes:
DIE VPLS MAC-Adressenabrechnung wird für jede VPLS-Instanz auf Mac-Adresse-Basis abgewickelt. Alle Informationen werden aus MAC-Adresseinträgen in der MAC-Adresstabelle abgerufen. VPLS MAC Address Accounting wird nur auf lokalen CE-Routern durchgeführt.
Die VPLS-Zähler für Quell- und Ziel-MAC-Adressen nehmen kontinuierlich zu, bis die ältesten MAC-Adresseneinträge aus dem Speicherpuffer entfernt werden, entweder wenn die Einträge eine Zeit überschritten oder die VPLS-Instanz neu gestartet wird.
user@PE1> show route forwarding-table family vpls extensive Routing table: green.vpls [Index 2] VPLS: Destination: default Route type: dynamic Route reference: 0 Flags: sent to PFE Next-hop type: flood Index: 353 Reference: 1 Destination: default Route type: permanent Route reference: 0 Flags: none Next-hop type: discard Index: 298 Reference: 1 Destination: fe-0/1/0.0 Route type: dynamic Route reference: 0 Flags: sent to PFE Next-hop type: flood Index: 355 Reference: 1 Destination: bb:bb:bb:bb:bb:bb/48 # This MAC address belongs to remote CE2. Route type: dynamic Route reference: 0 Flags: sent to PFE, prefix load balance Next-hop type: indirect Index: 351 Reference: 4 Next-hop type: Push 800000, Push 100002(top) Next-hop interface: so-1/1/0.0 Destination: aa:aa:aa:aa:aa:aa/48 # This MAC address belongs to local CE1. Route type: dynamic Route reference: 0 Flags: sent to PFE, prefix load balance Next-hop type: unicast Index: 354 Reference: 2 Next-hop interface: fe-0/1/0.0 user@PE1> show route forwarding-table family vpls Routing table: green.vpls VPLS: Destination Type RtRef Next hop Type Index NhRef Netif default dynm 0 flood 353 1 default perm 0 dscd 298 1 fe-0/1/0.0 dynm 0 flood 355 1 bb:bb:bb:bb:bb:bb/48 # This MAC address belongs to remote CE2. dynm 0 indr 351 4 Push 800000, Push 100002(top) so-1/1/0.0 aa:aa:aa:aa:aa:aa/48 # This MAC address belongs to local CE1. dynm 0 ucst 354 2 fe-0/1/0.0 user@PE1> show route forwarding-table family mpls Routing table: mpls MPLS: Destination Type RtRef Next hop Type Index NhRef Netif default perm 0 dscd 19 1 0 user 0 recv 18 3 1 user 0 recv 18 3 2 user 0 recv 18 3 100000 user 0 10.11.1.6 swap 100001 so-1/1/0.0 800002 user 0 Pop vt-0/3/0.32770 vt-0/3/0.32770 (VPLS) user 0 indr 351 4 Push 800000, Push 100002(top) so-1/1/0.0 user@PE1> show route instance green detail green: Router ID: 0.0.0.0 Type: vpls State: Active Interfaces: fe-0/1/0.0 # This is the local Fast Ethernet interface. vt-0/3/0.32770 # This is the dynamically generated VPLS virtual port. Route-distinguisher: 10.245.14.218:1 Vrf-import: [ __vrf-import-green-internal__ ] Vrf-export: [ __vrf-export-green-internal__ ] Vrf-import-target: [ target:11111:1 ] Vrf-export-target: [ target:11111:1 ] Tables: green.l2vpn.0 : 2 routes (2 active, 0 holddown, 0 hidden) user@PE1> show vpls connections L2VPN Connections: Legend for connection status (St) OR -- out of range WE -- intf encaps != instance encaps EI -- encapsulation invalid Dn -- down EM -- encapsulation mismatch VC-Dn -- Virtual circuit down CM -- control-word mismatch -> -- only outbound conn is up CN -- circuit not present <- -- only inbound conn is up OL -- no outgoing label Up -- operational NC -- intf encaps not CCC/TCC XX -- unknown NP -- interface not present Legend for interface status Up -- operational Dn -- down Instance: green Local site: greenPE1 (1) connection-site Type St Time last up # Up trans 2 rmt Up Jan 24 06:26:49 2003 1 Local interface: vt-0/3/0.32770, Status: Up, Encapsulation: VPLS Remote PE: 10.245.14.219, Negotiated control-word: No Incoming label: 800002, Outgoing label: 800000 user@PE1> show system statistics vpls vpls: 0 total packets received 0 with size smaller than minimum 0 with incorrect version number 0 packets for this host 0 packets with no logical interface 0 packets with no family 0 packets with no route table 0 packets with no auxiliary table 0 packets with no corefacing entry 0 packets with no CE-facing entry 7 mac route learning requests 7 mac routes learnt 0 mac routes aged 0 mac routes moved user@PE1> show route instance green detail green: Router ID: 0.0.0.0 Type: vpls State: Active Interfaces: fe-0/1/0.0 vt-0/3/0.32770 Route-distinguisher: 10.245.14.218:1 Vrf-import: [ __vrf-import-green-internal__ ] Vrf-export: [ __vrf-export-green-internal__ ] Vrf-import-target: [ target:11111:1 ] Vrf-export-target: [ target:11111:1 ] Tables: green.l2vpn.0 : 2 routes (2 active, 0 holddown, 0 hidden) user@PE1> show vpls statistics Layer-2 VPN Statistics: Instance: green Local interface: fe-0/1/0.0, Index: 351 Remote provider edge router: 10.245.14.219 Multicast packets: 363 Multicast bytes : 30956 Flood packets : 0 Flood bytes : 0 Local interface: vt-0/3/0.32770, Index: 354 Remote provider edge router: 10.245.14.219 Multicast packets: 135 Multicast bytes : 12014 Flood packets : 135 Flood bytes : 12014
Um alle MAC-Adresseinträge für eine VPLS-Instanz aus der VPLS-Tabelle zu löschen, erteilen Sie den clear vpls mac-address instance instance-name Befehl. Fügen Sie die Option zum Löschen von logical-system logical-system-name Einträgen in einer VPLS-Instanz innerhalb eines logischen Systems hinzu. Verwenden Sie die mac-address Option, um einzelne MAC-Adressen zu entfernen.