[
Contents]
[
Prev]
[
Next]
[
Index]
[
Report an Error]
Configuring General Settings
AIM General Settings allow the user
to do the following:
- Set the interval used by AIM to scan device archive locations
for Juniper Message Bundles (JMBs).
- Set the interval used by AIM to poll JSS for case status
updates.
- Set the interval used by AIM to poll JSS for intelligence
updates specific to your site.
- Set the amount of information sharing included in informational
JMBs. The default is Send only configuration indexes, which
indicates the technologies present in the device configuration. (See JMB Send Only Configuration Indexes Filter Example for an example of the
JMB Send only configuration indexes output.)
- Set the interval used to send newly detected information
JMBs to JSS.
- Set the port on which the AIM Service listens for requests
from the client. The default port number is the value set during the
AIM installation.
To configure AIM
General settings, follow these steps:
- In AIM, click the Settings Tab. The General Settings page
appears.
- Add the required AIM General settings. See AIM General Settings Page Description.
- Click Save Settings. This action saves the AIM General
settings that you modify and updates the AIM service with these new
settings.
AIM General Settings Page Description
Table 13 describes the General
Settings page command button.
Table 13: General Settings
Command Button
|
Button Name
|
Description
|
Privileges
|
Enabled/Disabled
|
Results
|
|
Save Settings
|
Saves any modified AIM general settings and updates the AIM
service with these new settings.
|
AIM Admin Settings
|
Enabled if admin privileges
|
Saves settings that were modified.
|
Table 14 describes the AIM
General Settings parameters.
Table 14: General Settings
Parameters
|
Name
|
Description
|
Privileges
|
Range/Length
|
Default
|
|
Incident Scan Interval (min):
|
Interval used to scan for new incidents in AIM archive locations.
|
AIM Admin Settings
|
0 = Off, 1 - 1440
(60 seconds - 24 hours)
|
3 minutes
|
|
Case Status Update Interval (min)
|
Interval used to poll for JTAC Case status updates from JSS
Case Manager
|
AIM Admin Settings
|
1 - 1440 minutes (60 seconds - 24 hours)
|
4 minutes
|
|
Intelligence Update Scan Interval (min)
|
Interval used to poll for intelligence updates for this site
in AIM archive locations.
|
AIM Admin Settings
|
1 - 1440 minutes (60 seconds - 24 hours)
|
3 minutes
|
|
Information JMB Config Filter Level
|
Specifies the amount of device configuration information in
Juniper Message Bundles to share with Juniper:
- Do not send—Sends no configuration information.
- Send all information except configuration—Sends
all device information except the configuration.
- Send only configuration indexes—Sends only the device
configuration technologies. (See JMB Send Only Configuration Indexes Filter Example
- Send all information with IP Addresses overwritten—Sends
all device information, without IP addresses
- Send all information—Sends all device information.
|
AIM Admin Settings
|
N/A
|
Do not send
|
|
Upload Information JMB Interval
|
Interval used to send any newly detected Intelligence JMBs to
JSS:
- On Detection
- Daily
- Weekly
- Monthly
|
AIM Admin Settings
|
N/A
|
Monthly
|
|
Local RMI Port
|
Port on which the AIM Service listens for requests from the
client
|
AIM Admin Settings
|
1-65535
|
1022
|
JMB Send Only Configuration Indexes Filter Example
If you select the Send Only Configuration Indexes Information
JMB Config Filter Level option in AIM General Settings, the device
configuration output displays only the hierarchy tags. The following
is an example of the Send Only Configuration Indexes option output.
[
Contents]
[
Prev]
[
Next]
[
Index]
[
Report an Error]
