 |
Note: The maximum number of redundancy groups is equal to the number of redundant Ethernet interfaces that you configure. |
Chassis clustering provides high availability of interfaces and services through redundancy groups and primacy within groups.
Before You Begin |
|---|
This topic includes:
A redundancy group is an abstract construct that includes and manages a collection of objects. A redundancy group contains objects on both nodes. A redundancy group is primary on one node and backup on the other at any time. When a redundancy group is said to be primary on a node, its objects on that node are active.
Redundancy groups are independent units of failover. Each redundancy group fails over from one node to the other independent of other redundancy groups. When a redundancy group fails over, all its objects fail over together.
Three things determine the primacy of a redundancy group: the priority configured for the node, the node ID (in case of tied priorities), and the order in which the node comes up. If a lower priority node comes up first, then it will assume the primacy for a redundancy group (and will stay as primary if preempt is not enabled).
A chassis cluster can include many redundancy groups, some of which might be primary on one node and some of which might be primary on the other. Alternatively, all redundancy groups can be primary on a single node. One redundancy group's primacy does not affect another redundancy group's primacy. You can create up to 128 redundancy groups.
|
Note: The maximum number of redundancy groups is equal to the number of redundant Ethernet interfaces that you configure. |
You can configure redundancy groups to suit your deployment. You configure a redundancy group to be primary on one node and backup on the other node. You specify the node on which the group is primary by setting priorities for both nodes within a redundancy group configuration. The node with the higher priority takes precedence, and the redundancy group's objects on it are active.
If a redundancy group is configured so that both nodes have the same priority, the node with the lowest node ID number always takes precedence, and the redundancy group is primary on it. In a two-node cluster, node 0 always takes precedence in a priority tie.
When you initialize a device in chassis cluster mode, the system creates a redundancy group referred to in this document as redundancy group 0. Redundancy group 0 manages the primacy and failover between the Routing Engines on each node of the cluster. As is the case for all redundancy groups, redundancy group 0 can be primary on only one node at a time. The node on which redundancy group 0 is primary determines which Routing Engine is active in the cluster. A node is considered the primary node of the cluster if its Routing Engine is the active one.
The redundancy group 0 configuration specifies the priority for each node. Below is how redundancy group 0 primacy is determined. Note that the three seconds value is the interval if the default heartbeat-threshold and heartbeat-interval values are used.
The above priority scheme applies to redundancy groups x as well, provided preempt is not configured.
You cannot enable preemption for redundancy group 0. If you want to change the primary node for redundancy group 0, you must do a manual failover.
 |
Caution: Be cautious and judicious in your use of redundancy group 0 manual failovers. A redundancy group 0 failover implies a Routing Engine failover, in which case all processes running on the primary node are killed and then spawned on the new primary Routing Engine. This failover could result in loss of state, such as routing state, and degrade performance by introducing system churn. |
You can configure one or more redundancy groups numbered 1 through 128, referred to in this chapter as redundancy group x. Each redundancy group x acts as an independent unit of failover and is primary on only one node at a time.
Each redundancy group x contains one or more redundant Ethernet interfaces. A redundant Ethernet interface is a pseudo interface that contains a pair of physical Gigabit Ethernet interfaces or a pair of Fast Ethernet interfaces. If a redundancy group is active on node 0, then the child links of all the associated redundant Ethernet interfaces on node 0 are active. If the redundancy group fails over to node 1, then the child links of all redundant Ethernet interfaces on node 1 become active.
On J-series and SRX-series chassis clusters, you can configure multiple redundancy groups to load-share traffic across the cluster. For example, you can configure some redundancy groups x to be primary on one node and some redundancy groups x to be primary on the other node. You can also configure a redundancy group x in a one-to-one relationship with a single redundant Ethernet interface to control which interface traffic flows through.
The traffic for a redundancy group is processed on the node where the redundancy group is active. Because more than one redundancy group can be configured, it is possible that the traffic from some redundancy groups will be processed on one node while the traffic for other redundancy groups is processed on the other node (depending on where the redundancy group is active). Multiple redundancy groups make it possible for traffic to arrive over an interface of one redundancy group and egress over an interface that belongs to another redundancy group. In this situation, the ingress and egress interfaces might not be active on the same node. When this happens, the traffic is forwarded over the fabric link to the appropriate node.
When you configure a redundancy group x, you must specify a priority for each node to determine the node on which the redundancy group x is primary. The node with the higher priority is selected as primary. The primacy of a redundancy group x can fail over from one node to the other. When a redundancy group x fails over to the other node, its redundant Ethernet interfaces on that node are active and their interfaces are passing traffic.
Table 66 gives an example of redundancy group x in an SRX-series chassis cluster and indicates the node on which the group is primary. It shows the redundant Ethernet interfaces and their interfaces configured for redundancy group x.
|
Note: SRX 210 devices have both Gigabit Ethernet ports and Fast Ethernet ports. |
Table 66: Redundancy Groups Example for an SRX-series Chassis Cluster (SRX 3000 and 5000 Lines)
As the example for an SRX-series chassis cluster in Table 66 shows:
Table 67 gives an example of redundancy groups x in a J-series chassis cluster and indicates the node on which each group is primary. It shows the redundant Ethernet interfaces and their interfaces configured for each redundancy group x.
Table 67: Redundancy Groups Example for a J-series Chassis Cluster
As the example for a J-series chassis cluster in Table 67 shows:
|
Note: Interface monitoring is not supported for redundancy group 0. |
For a redundancy group x to automatically fail over to another node, its interfaces must be monitored. When you configure a redundancy group x, you can specify a set of interfaces that the redundancy group x is to monitor for status (or “health”) to determine whether the interface is up or down. A monitored interface can be a child interface of any of its redundant Ethernet interfaces. When you configure an interface for a redundancy group x to monitor, you give it a weight.
Every redundancy group x has a threshold tolerance value initially set to 255. When an interface monitored by a redundancy group x becomes unavailable, its weight is subtracted from the redundancy group x's threshold. When a redundancy group x's threshold reaches 0, it fails over to the other node. For example, if redundancy group 1 was primary on node 0, on the threshold-crossing event, redundancy group 1 becomes primary on node 1. In this case, all the child interfaces of redundancy group 1's redundant Ethernet interfaces begin handling traffic.
A redundancy group x failover occurs because the cumulative weight of the redundancy group x's monitored interfaces has brought its threshold value to 0. When the monitored interfaces of a redundancy group x on both nodes reach their thresholds at the same time, the redundancy group x is primary on the node with the lower node ID, in this case node 0.
