|
Techpubs Home
Report an Error
Short Contents
Entire manual as PDF [2278 KB]
|
 |
- Chapter:
About This Guide
[PDF 39 KB]
- ERX Edge Routers
- Audience
- Conventions
- Documentation
- MIBs
- Release Notes
- Abbreviations
- Web Access
- Comments About the Documentation
- Contacting Customer Support
- Chapter:
Configuring Remote Access to the ERX System
[PDF 393 KB]
- Overview
- B-RAS Protocol Support
- B-RAS Data Flow
- Configuring IP Addresses for Remote Clients
- AAA Overview
- References
- Before You Configure B-RAS
- Configuration Tasks
- Configuring a B-RAS License
- Mapping a User Domain Name to a Virtual Router
- Mapping User Requests Without a Valid Domain Name
- Mapping User Requests Without a Configured Domain Name
- Preauthenticating Users
- Redirected Authentication
- IP Hinting
- Setting Up Domain Name and Realm Name Usage
- Using the Realm Name as the Domain Name
- Using Delimiters Other Than @
- Using Either the Domain or the Realm as the Domain Name
- Stripping the Domain Name
- Specifying a Single Name for Users from a Domain
- Configuring Authentication and Accounting Servers
- Server Access
- Server Request Processing Limit
- SNMP Traps and System Log Messages
- SNMP Traps
- System Log Messages
- UDP Checksums
- Configuring AA Servers
- Configuring SNMP Traps
- Configuring Name Server Addresses
- Configuration Tasks
- Configuring Local Address Servers
- Local Address Pool Ranges
- SNMP Thresholds
- Configuring a Local Address Server
- Configuring DHCP Features
- DHCP Overview
- Integrated DHCP Access Server
- Configuring a DHCP Proxy Client
- Configuring DHCP Relay and BOOTP Relay
- Creating an IP Interface
- Single Clients per ATM Subinterface
- Multiple Clients per ATM Subinterface
- Configuring AAA Profiles
- Allowing or Denying Domain Names
- Configuration Example
- Using Domain Name Aliases
- Configuration Example 1
- Configuration Example 2
- Using VSAs for Dynamic IP Interfaces
- Traffic Shaping for PPP over ATM Interfaces
- Configuring Timeout
- Limiting Active Subscribers
- Notifying RADIUS of AAA Failure
- Configuring the SDX Client
- Setting Baselines
- Monitoring Remote Access
- Chapter:
Configuring RADIUS Attributes
[PDF 231 KB]
- Overview
- RADIUS Services
- RADIUS Attributes
- References
- Subscriber AA Access Messages
- Access-Request Messages
- Access-Accept Messages
- Access-Reject Message
- Subscriber AA Accounting Messages
- Acct-Start Messages
- Acct-Stop Messages
- Interim-Acct Messages
- Acct-On Messages
- Acct-Off Messages
- Acct-Tunnel-Start Messages
- Acct-Tunnel-Stop Messages
- Acct-Tunnel-Reject Messages
- Acct-Tunnel-Link-Start Messages
- Acct-Tunnel-Link-Stop Messages
- Acct-Tunnel-Link-Reject Messages
- CLI AA Messages
- Access-Request Messages
- Access-Accept Messages
- Access-Challenge Messages
- Access-Reject Messages
- CLI Commands Used to Modify RADIUS Attributes
- Chapter:
Configuring TACACS+
[PDF 61 KB]
- Overview
- AAA Overview
- Administrative Login Authentication
- Privilege Authentication
- References
- Before You Configure TACACS+
- Configuring TACACS+
- Monitoring TACACS+
- Chapter:
Configuring L2TP
[PDF 224 KB]
- Overview
- References
- Terminology
- Implementing L2TP
- Sequence of Events on the LAC
- Sequence of Events on the LNS
- Packet Fragmentation
- Before You Configure the LAC or LNS
- Configuring the LAC
- Modules Supported by the LAC
- Mapping a User Domain Name to an L2TP Tunnel
- LNS Round-Robin Selection
- Configuring the LNS
- Host Profile Attributes
- Modules Supported by the LNS
- Enabling Tunnel Switching
- Enabling Tunnel Selection
- Enabling Tunnel Selection Failover Within a Preference Level
- Configuring Maximum Sessions per Tunnel
- Enabling Weighted Load Balancing
- Creating Persistent Tunnels
- Testing Tunnel Configuration
- Managing L2TP
- Monitoring Tunnels and Sessions
- Chapter:
Configuring L2F
[PDF 168 KB]
- Overview
- Terms
- Implementing L2F
- How L2F Works
- References
- Functionality
- L2F Encapsulation Details
- Egress/Ingress Behavior
- Egress/Ingress Rate Limiting
- Packet Fragmentation
- AAA Support
- Tunnel Authentication
- Connection Shutdown
- Configuring L2F
- Before You Begin
- Mapping a User Domain Name to an L2F Tunnel
- Configuration Steps
- Optional Tasks
- Managing L2F
- Monitoring L2F
- Chapter:
Configuring DHCP Local Server
[PDF 166 KB]
- Overview
- Line Module Support
- References
- DHCP Local Server Modes
- Equal-Access Mode
- Service Deployment System
- HTTP Local Server
- Local Pool Selection and Address Allocation
- The Connection Process
- Standalone Mode
- Local Pool Selection and Address Allocation
- Before You Configure DHCP Local Server
- Configuration Tasks
- Configuring the DHCP Local Server
- Configuring the System to Work with a RADIUS Server
- Configuring the System to Work with the SDX Application
- Configuring the HTTP Local Server
- Configuration Example
- Monitoring DHCP Local Server
- Monitoring the HTTP Local Server
- Monitoring the DHCP Local Server
- Chapter:
ERX-Supported RADIUS Attribute Descriptions
[PDF 88 KB]
- Chapter:
Index
[]
|
