This topic lists the Juniper Networks EX Series Ethernet Switches software features, the Juniper Networks Junos operating system (Junos OS) release in which they were introduced, and the first Junos OS release for each switch.
![]() | Note: For Virtual Chassis features, see EX Series Virtual Chassis Software Features Overview. |
The Junos OS release for software features on a switch cannot be earlier than the first Junos OS release for that switch.
Table 1: First Junos OS Release for Each EX Series Switch
Switch | Junos OS Release |
|---|---|
EX2200 switches* | Junos OS Release 10.1R1 *EX2200-C models: Junos OS Release 11.3R1 |
EX3200 switches | Junos OS Release 9.0R1 |
EX3300 switches | Junos OS Release 11.3R1 |
EX4200 switches | Junos OS Release 9.0R1 |
EX4500 switches* | Junos OS Release 10.2R1* *EX4500-C models: Junos OS Release 10.3R2 |
EX4550 switches | Junos OS Release 12.2R1 |
EX6200 switch | Junos OS Release 11.3R2 |
EX8208 switches | Junos OS Release 9.4R1 |
EX8216 switches | Junos OS Release 9.5R1 |
EX9200 switches | Junos OS Release 12.3R2 |
Table 2: Access Control Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
802.1X authentication (port-based, multiple supplicant) | 10.1R1 | 9.0R2 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.2R1 | Not sup- ported |
802.1X authentication with authentication bypass | 10.1R1 | 9.0R2 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.2R1 | Not sup- ported |
802.1X authentication with VLAN assignment, VoIP VLAN support | 10.1R1 | 9.0R1 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
802.1X user-based dynamic firewall filters | 10.1R1 | 9.0R2 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
802.1X user-based dynamic firewall filters on multiple-supplicant ports | 10.1R1 | 9.5R2 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
802.1X per-user statistics | 10.1R1 | 9.2R1 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R1 | 10.3R1 | Not sup- ported |
Authentication fallback | 11.3R1 | 10.3R1 | 12.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | Not sup- ported | Not sup- ported |
Captive portal authentication for Layer 3 interfaces | 11.3R1 | 10.1R1 | Not sup- ported | 12.1R1 | 12.2R1 | Not sup- ported | Not sup- ported | Not sup- ported |
Captive portal authentication for Layer 2 interfaces | 11.3R1 | 10.3R1 | 12.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | Not sup- ported | Not sup- ported |
Energy Efficient Ethernet (EEE) | Not supported | Not sup- ported | 12.2R1 | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported |
Infranet Controller (IC) as an external captive-portal server | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | Not sup- ported | Not sup- ported | Not sup- ported |
MAC RADIUS authentication | 10.1R1 | 9.3R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
NetBIOS snooping | 11.3R5 | 11.1R1 | 11.3R5 | Not sup- ported | Not sup- ported | 11.3R5 | 11.1R1 | Not sup- ported |
Server fail fallback | 10.1R1 | 9.3R2 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 10.2R1 | Not sup- ported |
TACACS+ | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | 12.3R2 |
Table 3: Administration Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
System logging (syslog) over IPv4 | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | 12.3R2 |
System logging (syslog) over IPv6 | 10.3R1 | 9.3R2 | 11.3R1 | 10.4R1 | 12.2R1 | 11.3R2 | 10.1R1 | 12.3R2 |
System snapshot | Not sup- ported | 10.0R1 | Not sup- ported | 10.2R1 | 12.2R1 | Not sup- ported | 10.0R1 | 12.3R2 |
Table 4: Class-of-Service (CoS) Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Class of service (CoS)—Class-based queuing with prioritization, Layer 2 and Layer 3 classification, rewrite, and queuing; strict priority queuing on egress | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | See Table 5 for a list of EX9200 CoS features |
CoS—DSCP, IEEE 802.1p, and IP precedence packet rewrites on routed VLAN interfaces (RVIs) | Not sup- ported | 9.5R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
CoS—Interface-specific classifiers on routed VLAN interfaces (RVIs) | Not sup- ported | 9.4R1 | 11.3R1 | 11.3R1 | 12.2R1 | Not sup- ported | 10.2R1 | |
CoS—Multidestination | – | – | – | – | – | Not sup- ported | 9.5R1 | |
CoS—Per-interface classification | Not sup- ported | 9.3R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 10.2R1 | |
CoS support on link aggregation groups (LAGs) | 10.1R1 | 9.2R1 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 9.4R1 | |
CoS support on routed VLAN interfaces (RVIs) | 10.3R1 | 9.4R1 | 11.3R1 | 10.4R1 | 12.2R1 | Not sup- ported | 9.4R1 | |
DSCP setting on ingress interface | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R1 | |
Flexible CoS-outer 802.1p marking | Not sup- ported | 9.6R1 | 12.3R1 | 12.1R1 | 12.2R1 | Not sup- ported | Not sup- ported | |
Interface-specific CoS rewrite rules | 10.3R1 | 9.4R1 | Not sup- ported | 11.2R1 | 12.2R1 | Not sup- ported | 10.2R1 | |
Junos EZQoS for CoS | 10.1R1 | 9.3R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Port shaping and queue shaping | 10.1R1 | 9.3R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 10.1R1 | |
Re-marking of bridged packets | 11.2R1 | 9.4R1 | Not sup- ported | 10.2R1 | 12.2R1 | 11.3R2 | 10.2R1 | |
Shaped-deficit weighted round-robin (SDWRR) | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Single-rate two-color marking | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 |
Table 5: Class-of-Service (CoS) Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Assigning forwarding class and DSCP value for Routing Engine generated traffic | 12.3R2 |
BA classification for VPLS based on IEEE 802.1p bits | 12.3R2 |
Classification—Associate packets with CoS servicing levels. Types of classification:
| 12.3R2 |
Classification and DSCP marking of distributed protocol handler traffic | 12.3R2 |
Classification of control-plane traffic | 12.3R2 |
CoS classification and rewrite for IRB and Layer 2 interfaces and for other Layer 3 interfaces. Port-level queuing, scheduling, and shaping are supported. | 12.3R2 |
Egress GRE classification based on DSCP | 12.3R2 |
IEEE 802.1p inheritance push and swap from transparent tags configuration | 12.3R2 |
Elevated packet drops during oversubscription | 12.3R2 |
Layer 2 policers for the ingress and egress interfaces. Policer types:
| 12.3R2 |
Independent values for DSCP and EXP bits | 12.3R2 |
Apply CoS schedulers on ingress interfaces | 12.3R2 |
Ingress DSCP bits for multicast traffic over Layer 3 VPNs | 12.3R2 |
Layer 2 traffic policing | 12.3R2 |
Policer support for aggregated Ethernet bundles (link aggregation groups, or LAGs) | 12.3R2 |
Queuing support for logical tunnel interfaces | 12.3R2 |
Rate-limit and excess rate or excess priority option | 12.3R2 |
Re-marking of MVPN GRE encapsulation DCSP at ASBR | 12.3R2 |
Scheduling | 12.3R2 |
Set IPv6 DSCP and MPLS EXP independently | 12.3R2 |
Set IPv6 DiffServ code point (DSCP) and MPLS EXP independently | 12.3R2 |
Support for Layer 2 policers at the VLAN level | 12.3R2 |
Support for applying a transmit rate limit to logical interfaces on Type 1, 2, or 3 Multiservices PICs | 12.3R2 |
Support for configuring ToS rewrite rules so that DCSP bits of GRE packets are consistent with service providers’ CoS policy | 12.3R2 |
Support for copying the TOS bits to the outer IP header on GRE tunnel traffic sent by the Routing Engine | 12.3R2 |
Support for setting the forwarding class and DSCP value for traffic generated by the Routing Engine | 12.3R2 |
Unified command to display all CoS statistics | 12.3R2 |
Table 6: Converged Networks (LAN and SAN) Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Note: The EX4500 switch models that support Fibre Channel over Ethernet features must be Converged Enhanced Ethernet (CEE) capable. The CEE-capable EX4500 switch models have a “–C” in the hardware model number. See EX4500 Switch Models. | ||||||||
Data Center Bridging Capability Exchange protocol (DCBX) | Not sup- ported | Not sup- ported | Not sup- ported | 11.3R1 | 12.2R1 | Not sup- ported | Not sup- ported | Not sup- ported |
DCBX application protocol TLV exchange | Not sup- ported | Not sup- ported | Not sup- ported | 12.1R1 | 12.2R1 | Not sup- ported | Not sup- ported | Not sup- ported |
FIP snooping | Not sup- ported | Not sup- ported | Not sup- ported | 10.4R1 | 12.2R1 | Not sup- ported | Not sup- ported | Not sup- ported |
Priority-based flow control (PFC) | Not sup- ported | Not sup- ported | Not sup- ported | 10.4R1 | 12.2R1 | Not sup- ported | Not sup- ported | Not sup- ported |
Table 7: Device Security Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Automatic recovery for port error disable conditions | 10.1R1 | 9.6R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 10.0R1 | Not sup- ported |
Storm control (broadcast and unicast) | 10.1R1 | 9.1R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | Not sup- ported |
Storm control (multicast) | 10.3R2 | 10.3R2 | Not sup- ported | 10.3R2 | 12.2R1 | 11.3R2 | 10.3R2 | Not sup- ported |
Unknown Layer 2 unicast forwarding | 10.1R1 | 9.3R2 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 10.0R1 | 12.3R2 |
Table 8: High Availability and Resiliency Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Note: For complete lists of Virtual Chassis features, see EX Series Virtual Chassis Software Features Overview. | SeeTable 9 for a list of EX9200 HA features. | |||||||
Graceful protocol restart for BGP | – | 9.0R2 | Not sup- ported | – | – | 11.3R2 | 9.4R1 | |
Graceful protocol restart for IS-IS | – | 9.3R2 | Not sup- ported | – | – | 11.3R2 | 9.4R1 | |
Graceful protocol restart for OSPF | – | 9.0R2 | Not sup- ported | – | – | 11.3R2 | 9.4R1 | |
Graceful protocol restart for RSVP and LDP | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R1 | |
GRES for ARP entries, forwarding database, and Layer 3 protocols | – | 9.2R1 | 11.3R1 | 11.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
GRES for IGMP snooping | – | 11.3R1 (Virtual Chassis only) | 12.1R1 (Virtual Chassis only) | 11.4R1 | 12.2R1 | Not sup- ported | 11.3R1 | |
GRES for LACP | Not sup- ported | 11.3R1 | Not sup- ported | 11.3R1 | 12.2R1 | Not sup- ported | 11.3R1 | |
GRES for Layer 2 and Layer 3 VPN LSPs | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R1 | |
GRES for port security (DHCP snooping, DAI, and IP source guard) | – | 9.2R1 | Not sup- ported | – | – | 11.3R2 | 9.6R1 | |
LACP support for dual-homing applications in data centers | 10.1R1 | 10.0R1 | Not sup- ported | 10.2R1 | 12.2R1 | Not sup- ported | 10.0R1 | |
Link Aggregation Control Protocol (LACP) | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Link aggregation groups (LAGs) | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Nonstop active routing (NSR) for BGP, IS-IS, IGMP with BFD, and RIP |
| 11.1R1 (Virtual Chassis only) | 12.1R1 (Virtual Chassis only) | 11.3R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) |
|
| |
Nonstop active routing (NSR) for IPv6 IS-IS, RIPng, and OSPFv3 with BFD | – | 12.2R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | Not sup- ported | 11.2R1 | |
Nonstop active routing (NSR) for OSPFv2 | – | 11.1R1 | 12.1R1 (Virtual Chassis only) | 11.2R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 11.3R2 | 10.4R1 | |
Nonstop active routing (NSR) for Protocol Independent Multicast (PIM) | Not sup- ported | 12.2R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | Not sup- ported | 11.4R2 | |
Nonstop active routing (NSR) for RSVP and LDP | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R1 | |
Nonstop bridging (NSB) for LAGs and LACP | – | 11.4R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 11.4R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.1R1 | 11.3R1 | |
Nonstop bridging (NSB) for LLDP and LLDP-MED | – | 11.3R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | Not sup- ported | Not sup- ported | Not sup- ported | 11.3R1 | |
Nonstop bridging (NSB) for spanning-tree protocols | – | 11.3R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.1R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.1R1 | 11.3R1 | |
Nonstop software upgrade (NSSU) | – | 12.1R1 (Virtual Chassis only) | 12.2R1 (Virtual Chassis only) | 12.1R1 (Virtual Chassis only) | 12.1R1 (Virtual Chassis only) | 12.2R1 | 10.4R1 | |
Power budget management | – | – | Not sup- ported | – | – | 11.3R2 | 10.2R1 | |
Virtual Router—Network Time Protocol (NTP), system logging, Simple Network Management Protocol (SNMP), RADIUS, and TACACS support in a virtual router | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 11.4R1 | |
Virtual Router Redundancy Protocol (VRRP) | 12.3R1 | 9.0R2 | 12.1R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Virtual Router Redundancy Protocol (VRRP)—Support for multiple VRRP owners per physical interface | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | Not sup- ported | 12.3R1 | |
Virtual Router Redundancy Protocol (VRRP) for IPv6 (except authentication type and authentication key) | Not sup- ported | 10.2R1 | 12.3R1 | 11.2R1 | 12.2R1 | 12.1R1 | 10.1R1 | |
Table 9: High Availability and Resiliency Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Graceful Routing Engine switchover (GRES) | 12.3R2 |
Nonstop active routing (NSR) support for Protocol Independent Multicast (PIM) for IPv4 and IPv6 | 12.3R2 |
Nonstop active routing (NSR) support for VPLS and for LDP-based VPLS | 12.3R2 |
Nonstop active routing (NSR) support for LDP OAM features | 12.3R2 |
Nonstop active routing (NSR) support for Layer 2 VPNs | 12.3R2 |
Virtual Router Redundancy Protocol version 3 (VRRPv3) | 12.3R2 |
Table 10: Interfaces Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Digital optical monitoring (DOM) | Not sup- ported | 10.0R1 | 11.3R1 | Not sup- ported | Not sup- ported | Not sup- ported | 10.0R1 | See Table 11 for a list of EX9200 interfaces features. |
Interface ranges | 10.1R1 | 10.0R1 | 11.3R1 | 10.2R | 12.2R1 | 11.3R2 | 10.1R1 | |
IPv4 over generic routing encapsulation (GRE) tunnels—encapsula-tion support | Not sup- ported | 12.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.1R1 | |
IPv4 over generic routing encapsulation (GRE) tunnels—de-encapsula-tion support | Not sup- ported | 12.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R1 | |
IPv6 over generic routing encapsulation (GRE) tunnels using IPv4 transport—encapsulation support | Not sup- ported | 12.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.1R1 | |
IPv6 over generic routing encapsulation (GRE) tunnels using IPv4 transport—de-encapsulation support | Not sup- ported | 12.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | |
IP directed broadcast | 11.3R1 | 9.4R1 | 12.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Time domain reflectometry (TDR) | 10.1R1 | 9.0R2 | 11.3R1 | Not sup- ported | Not sup- ported | 11.3R2 | 9.4R1 | |
Unicast reverse-path forwarding (RPF) | Not sup- ported | 9.3R2 | 12.3R1 | 11.2R1 | 12.2R1 | 11.3R2 | 10.1R1 | |
VLAN-tagged Layer 3 subinterfaces | Not sup- ported | 9.2R1 | Not sup- ported | 11.2R1 | 12.2R1 | 11.3R2 | 9.4R1 |
Table 11: Interfaces Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
ICMP redirect | 12.3R2 |
Clear MAC address information | 12.3R2 |
IPv6 subnet support on loopback interfaces | 12.3R2 |
IPv6 support for unnumbered Ethernet interfaces | 12.3R2 |
Multichassis link aggregation (MC-LAG) | 12.3R2 |
Nonstop active routing (NSR) support for Bidirectional Forwarding Detection (BFD) | 12.3R2 |
Protection against distributed denial-of-service (DDOS) attacks | 12.3R2 |
Software support for IPv4 to IPv6 transition | 12.3R2 |
Static mapping for port forwarding | 12.3R2 |
Support for active monitoring on logical systems | 12.3R2 |
Support for VRF in Routing Engine-based sampling | 12.3R2 |
Support for integrated routing and bridging (IRB) MAC synchronization in MC-LAG for aggregated Ethernet | 12.3R2 |
Targeted broadcast for virtual routing and forwarding (VRF) instances | 12.3R2 |
Trunk interface enhancements:
| 12.3R2 |
Unicast reverse-path forwarding (RPF) loose mode, with ability to discard packets with source addresses pointing to the discard interface | 12.3R2 |
Unnumbered Ethernet—Configure IPv4 processing on interfaces without assigning explicit IP addresses to the interfaces. | 12.3R2 |
VLAN rewrite operations on incoming and outgoing frames | 12.3R2 |
Table 12: IP Address Management Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
DHCP server and relay with option 82 for Layer 2 VLANs | 10.1R1 | 9.3R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | See Table 13 for a list
of EX9200 IP address manage- |
DHCP server and relay with option 82 for Layer 3 interfaces | 10.1R1 | 9.0R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
DNS for IPv6 | Not sup- ported | 9.3R2 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | |
Local DHCP server | 10.1R1 | 9.3R2 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Virtual router aware DHCP (VR-aware DHCP) | Not sup- ported | 12.3R1 | Not sup- ported | 12.3R1 | 12.3R1 | Not sup- ported | 12.3R1 | |
Virtual router aware DHCPv6 (VR-aware DHCPv6) | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R1 | 12.3R1 | 12.3R1 | Not sup- ported | |
Static addresses | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 9.4R1 |
Table 13: IP Address Management Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
DHCP server and relay | 12.3R2 |
DHCPv6 local server | 12.3R2 |
DHCPv6 support | 12.3R2 |
Distinguishing DHCP duplicate clients by subinterface | 12.3R2 |
Dynamic reconfiguration of extended DHCP and DHCPv6 local server clients | 12.3R2 |
Dynamic IPv6 filters | 12.3R2 |
Expression support for dynamic profiles | 12.3R2 |
Extended DHCP relay proxy | 12.3R2 |
Optional disabling of automatic ARP table population | 12.3R2 |
IPv6 address assignment pools | 12.3R2 |
Overriding DHCP settings on specific interfaces | 12.3R2 |
Per-interface DHCP tracing operations | 12.3R2 |
S-VLAN-based shaping for dynamic profiles | 12.3R2 |
Sending a DHCP relay and relay proxy release message | 12.3R2 |
Specifying the DHCP source address used for IP packets | 12.3R2 |
Support for MAC address validation | 12.3R2 |
Support for address pool threshold traps | 12.3R2 |
Address assignment pools | 12.3R2 |
Per-interface DHCP lease limits | 12.3R2 |
Table 14: IPv6 Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Note: A separate software license is required for IPv6. See Understanding Software Licenses for EX Series Switches. | ||||||||
Application identification (APPID) for IPv6 packets | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R2 |
BFD for IPv6 | Not sup- ported | 12.3R1 | Not sup- ported | 12.3R1 | 12.3R1 | Not sup- ported | 12.3R1 | 12.3R2 (also for static routes) |
BGP for IPv6 | Not sup- ported | 9.4R1 | 12.3R1 | 11.1R1 | 12.2R1 | 12.1R1 | 10.1R1 | 12.3R2 |
IPv6 CoS (multifield classification and rewrite) | Not sup- ported | 10.2R1 | 12.3R1 | 12.1R1 | 12.2R1 | 12.1R1 | 10.4R1 | 12.3R2 |
IPv6 management | 10.3R1 | 9.3R2 | 11.3R1 | 10.4R1 | 12.2R1 | Not sup- ported | 10.1R1 | 12.3R2 |
IPv6 multicast protocols (PIM, MLDv1/v2) | Not sup- ported | 10.1R1 | 12.3R1 | 11.2R1 | 12.2R1 | 12.1R1 | 10.2R1 | 12.3R2 |
IPv6 neighbor redirect compliance with RFC 4861 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R2 |
IPv6 path MTU discovery | 10.3R1 | 9.3R1 | 12.3R1 | 10.4R1 | 12.2R1 | Not sup- ported | 10.2R1 | 12.3R2 |
IS-IS for IPv6 | Not sup- ported | 9.4R1 | Not sup- ported | 11.2R1 | 12.2R1 | 12.1R1 | 10.1R1 | 12.3R2 |
MBGP for IPv6 | Not sup- ported | 9.3R1 | 12.3R1 | Not sup- ported | Not sup- ported | 12.1R1 | 10.1R1 | 12.3R2 |
OSPFv3 | Not sup- ported | 9.3R1 | 12.3R1 | 11.1R1 | 12.2R1 | 12.1R1 | 10.1R1 | 12.3R2 |
RFC 4291 Compliance | 12.3R1 See note at end of table | 12.3R1 See note at end of table | 12.3R1 See note at end of table | 12.3R1 See note at end of table | 12.3R1 See note at end of table | 12.3R1 See note at end of table | 12.3R1 See note at end of table | 12.3R2 See note at end of table |
RIPng | Not sup- ported | 9.3R1 | 12.3R1 | 11.1R1 | 12.2R1 | 12.1R1 | 10.1R1 | 12.3R2 |
VRRPv3 (RFC 5798 Compliance, ability to send SNMP traps) | Not sup- ported | 12.3R1 | Not sup- ported | 12.3R1 | 12.3R1 | Not sup- ported | 12.3R1 | 12.3R2 |
![]() | Note: Compliance with RFC 4291—EX Series switches drop the following types of illegal IPv6 packets:
|
Table 15: Layer 2 Network Protocols Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
802.1Q VLAN tagging | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | See Table 16for a list of EX9200 Layer 2 networking protocols features.
|
Edge virtual bridging (EVB) support with virtual Ethernet port aggregator (VEPA) | Not sup- ported | Not sup- ported | Not sup- ported | 12.1R1 | 12.2R1 | Not sup- ported | 12.1R1 | |
Ethernet ring protection switching (ERPS, G.8032/Y.1344) | 12.1R1 | 12.1R1 | 12.3R1 | 12.3R1 | 12.3R1 | Not sup- ported | 12.3R1 | |
Layer 2 protocol tunneling (L2PT) | 11.1R1 | 10.0R1 | 12.3R1 | 11.2R1 | 12.2R1 | 12.1R1 | Not sup- ported | |
Link Layer Discovery Protocol (LLDP) | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Link Layer Discovery Protocol–Media Endpoint Discovery (LLDP-MED) with voice over IP (VoIP) integration | 10.1R1 | 9.0R2 | 11.3R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | |
MAC-based VLANs | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Multiple VLAN Registration Protocol (MVRP, IEEE 802.1ak) | 11.3R1 | 10.0R1 | 12.3R1 | 11.2R1 | 12.2R1 | 12.1R1 | 10.0R1 | |
Private VLANs (PVLANs) | 11.1R1 | 9.3R2 | 12.1R1 | 11.2R1 | 12.2R1 | 11.3R2 | 10.1R1 | |
Private VLANs (PVLANs) support across switches | 11.1R1 | 10.4R1 | 12.1R1 | 11.2R1 | 12.2R1 | 11.3R2 | 11.2R1 | |
Proxy ARP—Restricted | 10.1R1 | 10.0R1 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 10.0R1 | |
Proxy ARP—Unrestricted | 10.1R1 | 9.6R1 | 11.3R1 | 10.2R1 | 12.2R1 | 12.1R1 | 10.0R1 | |
Proxy ARP per VLAN | 10.1R1 | 10.1R1 | Not sup- ported | 10.2R1 | 12.2R1 | Not sup- ported | 10.1R1 | |
Q-in-Q tunneling | 11.1R1 | 9.3R2 | 11.4R1 | 11.2R1 | 12.2R1 | 12.1R1 | 11.1R1 | |
Q-in-Q VLAN extended support for multiple S-VLANs per access interface, firewall-filter-based VLAN assignment, and routed VLAN interfaces (RVIs) | Not sup- ported | 9.6R1 | 12.3R1 | 11.2R1 | 12.2R1 | 12.1R1 | 11.1R1 | |
Redundant trunk groups | 10.1R1 | 9.0R2 | 11.3R1 | 11.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Routed VLAN interfaces(RVIs)—Also known as integrated routing and bridging (IRB) interfaces | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
VLAN ID translation | 11.1R1 | 10.0R1 | Not sup- ported | 11.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
VLAN ranges | 10.1R1 | 9.2R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 |
Table 16: Layer 2 Networking Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
VLANs and virtual switching | 12.3R2 |
DHCP support for integrated routing and bridging (IRB) | 12.3R2 |
MC-LAG support for IGMP snooping in IRB | 12.3R2 |
Hash-key load-balancing support for Layer 3 and Layer 4 fields | 12.3R2 |
IP multicast over Layer 2 trunk port support | 12.3R2 |
Integrated routing and bridging (IRB) | 12.3R2 |
Layer 2 Ethernet OAM:
| 12.3R2 |
Layer 2 address learning in logical systems | 12.3R2 |
Layer 2 forwarding support for bridging and VPLS | 12.3R2 |
Layer 2 policer statistics MIB | 12.3R2 |
Firewall filter match conditions for Layer 2 bridging and VPLS | 12.3R2 |
Next-hop groups using either IP addresses or Layer 2 addresses for the next hop | 12.3R2 |
Unicast reverse-path forwarding (RPF) loose mode, with ability to discard packets with source addresses pointing to the discard interface | 12.3R2 |
Spanning-tree protocols support for Layer 2 bridging and VPLS | 12.3R2 |
VLAN rewrite operations on incoming and outgoing frames | 12.3R2 |
STP root guard (root protection) | 12.3R2 |
Support for Layer 2 and Layer 2.5 features:
| 12.3R2 |
VPLS root protection topology change-action control | 12.3R2 |
VLAN ranges | 12.3R2 |
Q-in-Q VLAN extended support for multiple S-VLANs per access interface, firewall-filter-based VLAN assignment, and routed VLAN interfaces (RVIs) | 12.3R2 |
Q-in-Q tunneling | 12.3R2 |
Proxy ARP—Unrestricted and restricted | 12.3R2 |
MAC-based VLANs | 12.3R2 |
Link Layer Discovery Protocol (LLDP) | 12.3R2 |
Layer 2 protocol tunneling (L2PT) | 12.3R2 |
Table 17: Layer 3 Protocols Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Bidirectional Forwarding Detection (BFD) | 11.3R1 | 9.0R2 | 12.1R1 | 10.2R1 | 12.2R1 | 12.1R1 | 9.4R1 | See Table 18 for a list of EX9200 Layer 3 protocols features. |
Border Gateway Protocol (BGP) | Not sup- ported | 9.0R2 | 12.1R1 | 11.1R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Multiprotocol Border Gateway Protocol (MBGP) | Not sup- ported | 9.3R1 | 12.3R1 | 11.2R1 | 12.2R1 | 12.1R1 | 9.4R1 | |
A separate software license is required for BGP and MBGP. See Understanding Software Licenses for EX Series Switches. | ||||||||
Distributed periodic packet management (PPM) with BFD | Not sup- ported | 10.4R1 | Not sup- ported | Not sup- ported | Not sup- ported | 12.1R1 | 10.4R1 | |
Distributed periodic packet management (PPM) with LACP | Not sup- ported | 10.2R1 | Not sup- ported | 11.1R1 | 12.2R1 | 11.3R2 | 10.2R1 | |
Filter-based forwarding | Not sup- ported | 9.4R1 | 12.3R1 | 11.2R1 | 12.2R1 | 11.3R2 | 9.6R1 | |
Filter-based forwarding over IPv6 | Not sup- ported | 10.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 10.3R1 | |
Intermediate System-to- | Not sup- ported | 9.0R2 | Not sup- ported | 11.1R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
A separate software license is required for IS-IS. See Understanding Software Licenses for EX Series Switches. | ||||||||
IPv6 Layer 3 multicast protocols | Not sup- ported | 10.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 10.2R1 | |
Jumbo frames on routed VLAN interfaces (RVIs) | Not sup- ported | 9.4R1 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 9.4R1 | |
OSPF Multitopology Routing (MT-OSPF) | Not sup- ported | 9.5R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | |
OSPFv2 | 11.1R1 | 9.0R2 | 11.4R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
OSPFv3 IPsec support | Not sup- ported | 10.3R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | |
Routing Information Protocol version 1 (RIPv1) and RIPv2 | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Static routes | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Virtual routing and forwarding (VRF) with IPv4—Virtual routing instances | 12.3R1 | 9.2R1 | 12.3R1 | 11.1R1 | 12.2R1 | 11.3R2 | 9.6R1 | |
VRF with IPv4—Virtual routing instances for PIM and IGMP | Not sup- ported | 10.0R1 | Not sup- ported | 11.1R1 | 12.2R1 | 11.3R2 | 10.0R1 | |
VRF with IPv4—Virtual routing instances for IGMP snooping | Not sup- ported | 11.4R1 | Not sup- ported | 12.1R1 | 12.2R1 | Not sup- ported | 11.3R1 | |
VRF with IPv6—Virtual routing instances for multicast traffic | Not sup- ported | 10.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 10.1R1 | |
VRF with IPv6—Virtual routing instances for unicast traffic | Not sup- ported | 10.1R1 | 12.3R1 | Not sup- ported | Not sup- ported | Not sup- ported | 10.1R1 | |
Table 18: Layer 3 Protocols Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Accumulated IGP attribute for BGP | 12.3R2 |
Advertisement of the best external BGP path to internal peers | 12.3R2 |
Alias support for local autonomous system numbers for BGP | 12.3R2 |
BFD liveness detection | 12.3R2 |
BFD protocol support for OSPFv3 | 12.3R2 |
BGP remote next-hop support for single-hop EBGP peers | 12.3R2 |
BGP support for 4-byte autonomous system numbers | 12.3R2 |
BGP support for MDT-SAFI updates without a route target | 12.3R2 |
Behavior change for BGP-independent autonomous system (AS) domains | 12.3R2 |
Bidirectional Forwarding Detection (BFD) hold-down timer | 12.3R2 |
Distributed periodic packet management support for aggregate interfaces | 12.3R2 |
Egress filtering PIMv4/v6 join messages | 12.3R2 |
For internal BGP (IBGP), advertise multiple paths to a destination | 12.3R2 |
Frequent BGP keepalive messages and short BGP hold time | 12.3R2 |
Hitless authentication key rollover for IS-IS | 12.3R2 |
Hub-and-spoke support for multiprotocol BGP-based multicast VPNs with PIM-SSM GRE S-PMSI transport | 12.3R2 |
IPv4 subnet support on loopback interfaces | 12.3R2 |
IS-IS hold-down timer for subsequent SPF calculations | 12.3R2 |
Keepalive support for GRE interfaces | 12.3R2 |
Multitopology routing (MTR) | 12.3R2 |
Nonstop active routing (NSR) support for the Routing Information Protocol (RIP) and RIP next generation (RIPng) | 12.3R2 |
Nonstop active routing (NSR) support | 12.3R2 |
OSPF graceful restart enhancement | 12.3R2 |
OSPF hold-down timer for subsequent SPF calculations | 12.3R2 |
Only the system log notes failure to add routes | 12.3R2 |
Origin validation for BGP | 12.3R2 |
PIM join suppression support | 12.3R2 |
Priority assignment for prefixes in OSPF import policies | 12.3R2 |
Reduction in flooding of self-originated OSPF LSAs | 12.3R2 |
Support for BFD over multihop static routes | 12.3R2 |
Support for BFD on logical switches | 12.3R2 |
Support for IPSec authentication for OSPFv2 | 12.3R2 |
Support for OSPF database protection for OSPF and OSPFv3 | 12.3R2 |
Support for OSPF export and import policies for network-summary LSAs | 12.3R2 |
Support for alternate loop-free routes for IS-IS and OSPF | 12.3R2 |
Support for clearing the VPN tag | 12.3R2 |
Support for disabling the attribute set messages on independent AS domains for BGP loop detection | 12.3R2 |
Support for disabling traps for passive OSPFv2 interfaces | 12.3R2 |
Support for display of flood next-hop branch overflow condition | 12.3R2 |
Support for dropping and ignoring path attributes during BGP neighbor updates | 12.3R2 |
Support for the algorithm that determines the single best path to skip the step that evaluates an AS path | 12.3R2 |
Support for limiting the number of prefixes accepted from a BGP peer | 12.3R2 |
Support for multiarea adjacency in OSPFv2 | 12.3R2 |
Support for multiple address families in OSPFv3 | 12.3R2 |
Support for route leaking when the switch is in overload mode | 12.3R2 |
Support for route-filter-based BGP outbound route filtering | 12.3R2 |
Support for the BGP Monitoring Protocol | 12.3R2 |
Support to hold down BGP peering sessions after a nonstop active routing (NSR) switchover Timer to delay MED updates for routes advertised by BGP groups or peers configured with the metric-out igp statement Virtual Router Redundancy Protocol (VRRP) | 12.3R2 |
Timer to delay MED updates for routes advertised by BGP groups or peers configured with the metric-out igp statement | 12.3R2 |
Virtual Router Redundancy Protocol (VRRP) | 12.3R2 |
Table 19: Logical Systems Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
A separate software license is required for logical systems. See Understanding Software Licenses for EX Series Switches. | |
Logical systems | |
Layer 2 address learning in logical systems | 12.3R2 |
Table 20: MPLS Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
A separate software license is required for MPLS. See Understanding Software Licenses for EX Series Switches. | ||||||||
Aggregated Ethernet interfaces (LAGs) on circuit cross-connects (CCCs) | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | See Table 21 for a list of EX9200 MPLS features. |
BFD for an LDP-based LSP | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | |
BFD for an RSVP-based LSP | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | |
CCC between 2 interfaces in the same switch | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
Interior gateway protocol (IGP) IS-IS and OSPF shortcuts | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
IP over MPLS | Not sup- ported | 10.1R1 | Not sup- ported | 12.2R1 See Note at end of table | 12.2R1 See Note at end of table | Not sup- ported | 11.1R1 | |
IPv6 over MPLS label-switched paths (LSPs) | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 See Note at end of table | 12.2R1 See Note at end of table | Not sup- ported | 12.1R1 | |
LDP-based MPLS | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
LDP tunneling (LDP over RSVP) | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS-based circuit cross-connects (CCC) | Not sup- ported | 9.5R1 | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS label-switched router (LSR) support | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS Layer 2 CCC on Ethernet-encapsulated interfaces (RFC 6624) | Not sup- ported | 9.5R1 | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS Layer 2 CCC on VLAN-encapsulated interfaces (RFC 4905) | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS Layer 2 VLAN CCC on Ethernet-encapsulated interfaces (RFC 6624) | Not sup- ported | 9.5R1 | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.3R1 | |
MPLS Layer 2 VLAN CCC on VLAN-encapsulated interfaces (RFC 4905) | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.3R1 | |
MPLS Layer 2 VPN over CCC | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS Layer 2 VPN over VLAN CCC | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.3R1 | |
MPLS OAM-LSP ping | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 11.1R1 | |
MPLS over untagged Layer 3 interfaces | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS with class of service (CoS) | Not sup- ported | 9.5R1 | Not sup- ported | 12.2R5 | 12.2R5 | Not sup- ported | 12.1R1 | |
MPLS Layer 3 VPNs | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
MPLS with RSVP-based label-switched paths (LSPs) | Not sup- ported | 9.5R1 | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
Layer 3 subinterfaces as MPLS core interfaces | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 See Note at end of table. | 12.2R1 See Note at end of table. | Not sup- ported | 12.1R1 | |
Routed VLAN interfaces (RVIs) as MPLS core interfaces | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.1R1 | |
Path maximum transmission unit (MTU) and unicast reverse-path forwarding (RPF) checks for VPNs | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
Resource Reservation Protocol—traffic engineering (RSVP-TE) | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
Standby secondary path protection | Not sup- ported | 12.1R1 | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 11.1R1 | |
Static label-switched paths (LSPs) | Not sup- ported | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported | 12.1R1 | |
![]() | Note: Layer 3 subinterfaces as MPLS core interfaces—For EX4500 and EX4550 switches to support Layer 3 subinterfaces as MPLS core interfaces, the peer switch that the Layer 3 subinterfaces connect to, must be an EX8200 switch. IP over MPLS—The EX4500 and EX4550 switches do not support IP over MPLS (single MPLS label in the packet) when the switch is positioned as a non-penultimate-hop popping (non-PHP) switch. |
Table 21: MPLS Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
A separate software license is required for MPLS. See Understanding Software Licenses for EX Series Switches. | |
Bypass static LSPs | 12.3R2 |
LDP LSP action based on a BFD failure event | 12.3R2 |
LDP downstream on demand | 12.3R2 |
LDP, BGP, and VPLS interworking | 12.3R2 |
P2MP LSP traceroute | 12.3R2 |
Static LSP:
| 12.3R2 |
Statistics for P2MP LSPs | 12.3R2 |
Table 22: Multicast Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
IGMP (Internet Group Management Protocol) version 1 (IGMPv1) and IGMPv2 | 11.1R1 | 9.0R2 | 12.1R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | See Table 23 for a list of EX9200 multicast features |
IGMP filtering | 11.3R1 | 9.5R1 | 12.3R1 | 11.3R1 | 11.3R1 | 11.3R1 | 9.5R1 | |
IGMP snooping with routed VLAN interfaces (RVIs) | 10.1R1 | 9.2R1 | 12.1R1 | 10.2R1 | 12.2R1 | Not sup- ported | 9.4R1 | |
IGMPv3 | 11.1R1 | 9.3R2 | 12.1R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.6R1 | |
IGMPv1 and IGMPv2 snooping | 10.1R1 | 9.1R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
IGMPv3 snooping | 10.1R1 | 9.6R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.6R1 | |
Multicast Listener Discovery version 1 and 2 (MLDv1 and MLDv2) | Not sup- ported | 10.1R1 | Not sup- ported | 11.2R1 | 12.2R1 | 12.1R1 | 10.2R1 | |
Multicast Listener Discovery version 1 (MLDv1) snooping (MLDv1 snooping) | 12.1R1 | 12.1R1 | 12.1R1 | 12.1R1 | 12.2R1 | 12.1R1 | 12.1R1 | |
Multicast Listener Discovery version 2 (MLDv2) snooping (MLDv2 snooping) | 12.1R1 | 12.1R1 | 12.1R1 | 12.1R1 | 12.2R1 | 12.1R1 | 12.1R1 | |
Multicast Source Discovery Protocol (MSDP) | Not sup- ported | 9.4R1 | 12.3R1 | 10.2R1 | 12.2R1 | 12.1R1 | 9.4R1 | |
Multicast VLAN registration (MVR) | 11.3R1 | 9.6R1 | 12.1R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | |
Protocol Independent Multicast dense mode (PIM DM) | 11.1R1 | 9.2R1 | 12.1R1 | 11.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Protocol Independent Multicast sparse mode (PIM SM) | 11.1R1 | 9.0R2 | 12.1R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Protocol Independent Multicast source-specific multicast (PIM SSM) | 11.1R1 | 9.3R1 | 12.1R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Single-source multicast | Not sup- ported | 9.0R2 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 9.4R1 | |
Table 23: Multicast Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
BFD for PIM—IPv6 | 12.3R2 |
BFD support for ECMP LSPs signaled using LDP | 12.3R2 |
Bidirectional PIM (RFC 5015) | 12.3R2 |
Control of PIM resources for multicast VPNs | 12.3R2 |
Disable PIM for IPv6 only | 12.3R2 |
Dynamic reuse of data multicast distribution tree (MDT) group addresses | 12.3R2 |
Flexible configuration for IGMP or MLD static-join | 12.3R2 |
IGMPv3 and MLDv2 full support | 12.3R2 |
IGMP and MLD enhancements–
| 12.3R2 |
IGMP and PIM support for unnumbered interfaces | 12.3R2 |
IGMP join and leave recording for system or for specific interfaces | 12.3R2 |
IGMP and MLD source or group access lists and MLD join and leave recording | 12.3R2 |
IGMP and MLD support for dynamic interfaces | 12.3R2 |
Independently configurable loopback addresses for VRF VPNs | 12.3R2 |
Internet multicast using ingress replication provider tunnels | 12.3R2 |
Software support for configuring accept any-source multicast (ASM) join messages (*,G) for group addresses | 12.3R2 |
Software support for configuring a provider network to operate in source-specific multicast (SSM) mode | 12.3R2 |
LDP signaling for point-to-multipoint LSPs in next-generation MBGP multicast VPNs | 12.3R2 |
Load-balancing PIM join messages on multicast VPNs | 12.3R2 |
Multicast flow maps | 12.3R2 |
Nonstop active routing (NSR) PIM for Draft-Rosen VPNs | 12.3R2 |
PIM automatic make-before-break (MBB) join load balancing | 12.3R2 |
PIM join load balancing | 12.3R2 |
Source-specific multicast (SSM)-map definition for different groups to different sources | 12.3R2 |
Support for filtering unwanted PIM neighbors | 12.3R2 |
Support for multicast output interface (OIF) mapping | 12.3R2 |
Translation of PIM join/prune messages to IGMP or MLD report/leave messages | 12.3R2 |
Turn off spanning-tree interface state in multicast snooping | 12.3R2 |
Table 24: Network Management and Monitoring Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
802.1ag Ethernet OAM connectivity fault management (CFM) | 11.2R1 | 10.2R1 | 12.3R1 | 12.2R1 | 12.2R1 | Not sup- ported | 11.4R1 | See Table 25 for a list of
EX9200 network manage- |
Ethernet frame delay measurement (ETH-DM, Y.1731) | Not sup- ported | 11.4R1 (EX4200 only) | Not sup- ported | 11.4R1 | 12.2R1 | Not sup- ported | 11.4R1 | |
Ethernet OAM link fault management (LFM—also known as Ethernet in the First Mile, EFM) | 11.1R1 | 9.4R1 | 12.2R1 | 12.2R1 | 12.2R1 | Not sup- ported | 10.0R1 | |
Port mirroring | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Port mirroring enhancements
| Not sup- ported | 9.5R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 9.5R1 | |
Port mirroring enhancements
| Not sup- ported | 10.0R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | |
Port mirroring support for multiple analyzers per session | Not sup- ported | Not sup- ported | Not sup- ported | 11.2R1 | 12.2R1 | Not sup- ported | Not sup- ported | |
Real-time performance monitoring (RPM) | 10.1R1 | 9.3R2 | 12.2R1 | 10.2R1 | 12.2R1 | 12.1R1 | 10.1R1 | |
Real-time performance monitoring (RPM)—hardware timestamps with routed VLAN interfaces (RVIs) | Not sup- ported | 10.3R1 | 12.2R1 | 10.2R1 | 12.2R1 | 12.1R1 | 10.3R1 | |
Real-time performance monitoring (RPM)—client and server on same interface | 10.3R1 | 10.3R1 | 12.2R1 | 11.1R1 | 12.2R1 | Not sup- ported | 10.3R1 | |
Routing Engine Software Development Kit (SDK) | Not sup- ported | 12.2R1 | 12.2R1 (EX4200 only) | 12.2R1 | 12.2R1 | Not sup- ported | 12.2R1 | |
RMON | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
sFlow monitoring technology | 11.1R1 | 9.3R2 | 12.1R1 | 11.2R1 | 12.2R1 | 12.1R1 | 10.0R1 | |
sFlow monitoring technology—Persistent IP addresses for agent IDs and use in datagrams | 11.1R1 | 10.2R1 | Not sup- ported | Not sup- ported | Not sup- ported | 12.1R1 | 10.2R1 | |
Simple Network Management Protocol version 1 (SNMPv1), SNMPv2, and SNMPv3 | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Uplink failure detection | 11.1R1 | 11.1R1 | 12.1R2 | 11.1R1 | 12.2R1 | Not sup- ported | 12.1R1 |
Table 25: Network Management and Monitoring Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Junos OS XML API and scripting—NETCONF Java toolkit for rapid development of Java applications to manage devices running Junos OS | 12.3R2 |
Junos OS XML API and scripting—NETCONF Perl client installation—Supports loading prerequisites from Comprehensive Perl Archive Network (CPAN) global repository | 12.3R2 |
Junos OS XML API and scripting—NETCONF tracing operations | 12.3R2 |
Junos OS XML API and scripting:
| 12.3R2 |
Configuration options to filter out interfaces from SNMP Get and GetNext operations | 12.3R2 |
Enhanced SNMP support for logical switches and routing instances | 12.3R2 |
Generating SNMP traps when MAC address table is full | 12.3R2 |
Junos OS MIB support for VPLS | 12.3R2 |
MIB support for VRF route entries | 12.3R2 |
Proxy SNMP agent | 12.3R2 |
SNMP MIB support for OSPFv3 | 12.3R2 |
SNMP poll and trap support for DHCP leases | 12.3R2 |
SNMP support for the DHCP bindings table | 12.3R2 |
SNMP support for the authd daemon and for radius-acc-server-mib and radius-auth-server-mib | 12.3R2 |
SNMP support for spanning-tree protocols | 12.3R2 |
Support for Internet draft draft-ieft-bfd-mib-02.txt—MIB for BFD liveness detection | 12.3R2 |
Support for MIB objects in accounting profiles | 12.3R2 |
Support for an enterprise-specific event MIB (mib-jnx-event.txt) | 12.3R2 |
Support for sending traps over routing instances | 12.3R2 |
Support for adding lists of clients to the SNMP community | 12.3R2 |
Support for the enterprise-specific Packet Forwarding Engine MIB (mib-jnx-pfe.txt) | 12.3R2 |
Support for the pimNeighborLoss trap | 12.3R2 |
Support for trap spoofing | 12.3R2 |
IEEE 802.3ah link fault management (LFM) for Ethernet OAM (also known as Ethernet in the First Mile, or EFM) | 12.3R2 |
Port mirroring of Layer 2 VLAN and VPLS traffic | 12.3R2 |
Fast update filters for dynamic profiles | 12.3R2 |
Flow aggregation to multiple collectors | 12.3R2 |
IPv6 flow aggregation templates | 12.3R2 |
Inline flow monitoring | 12.3R2 |
Table 26: Power over Ethernet (PoE) Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Link Layer Discovery Protocol (LLDP) with granular Power over Ethernet (PoE) management | 12.2R1 | 12.2R1 (EX4200- | 12.2R1 | Not sup- ported | Not sup- ported | 12.2R1 | 12.2R1 | Not sup- ported |
Note: EX4200 switches must be running PoE controller software firmware version 4.04 or later to support the Link Layer Discovery Protocol (LLDP) with granular Power over Ethernet (PoE) management feature. See show chassis firmware detail and request system firmware upgrade poe to check or upgrade this firmware. | Not sup- ported | |||||||
Power over Ethernet (PoE) | 10.1R1 | 9.0R2 | 11.3R1 | – | – | 11.3R2 | 11.2R1 | Not sup- ported |
Power over Ethernet Plus (PoE+) | 10.3R1 | Not sup- ported | 11.3R1 | – | – | 11.3R2 | 11.2R1 | Not sup- ported |
Power over Ethernet (PoE) power management mode | 10.1R1 | 9.3R2 | 11.3R1 | – | – | 11.3R2 | 11.2R1 | Not sup- ported |
Table 27: Port Security Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Automatic recovery for port error disable conditions | 10.1R1 | 9.6R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 10.0R1 | Not sup- ported |
DHCP option 82 | 10.1R1 | 9.3R2 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 9.4R1 | 12.3R2 |
DHCP snooping | 10.1R1 | 9.0R2 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
Dynamic ARP inspection (DAI) | 10.1R1 | 9.0R2 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
IP source guard | 10.1R1 | 9.2R1 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
Layer 3 virtual private network (VPN) for IPv4 (RFC 2547 and 4364) | Not sup- ported | Not sup- ported | Not sup- ported | Not supported | Not supported | Not sup- ported | Not supported | 12.3R2 |
Layer 3 virtual private network (VPN) for IPv6 through IPv4 MPLS | Not sup- ported | Not sup- ported | Not sup- ported | Not supported | Not supported | Not sup- ported | Not supported | 12.3R2 |
MAC limiting | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | 12.3R2 |
MAC address limit per port | 10.1R1 | 9.0R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 10.3R1 | 12.3R2 |
MAC limiting per port and per VLAN (VLAN membership MAC limit) | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R2 |
MAC move limiting | 10.1R1 | 9.0R2 | 11.3R1 | Not sup- ported | Not sup- ported | 11.3R2 | Not sup- ported | Not sup- ported |
Persistent MAC learning (sticky MAC) | 11.4R1 | 11.4R1 | 12.3R1 | 11.4R1 | 12.2R1 | 11.4R1 | 11.4R1 | Not sup- ported |
Persistent storage for DHCP snooping | 10.1R1 | 9.4R1 | 11.3R1 | 12.1R1 | 12.2R1 | 11.3R2 | 10.3R1 | Not sup- ported |
Self-signed digital certificates for enabling SSL services | 11.1R1 | 11.1R1 | Not sup- ported | 11.1R1 | 12.2R1 | 12.1R1 | 11.1R1 | Not sup- ported |
Static ARP support | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | Not sup- ported |
Table 28: Routing Policy and Packet Filtering Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Dynamic allocation of TCAM memory to firewall filters | 10.1R1 | 10.0R1 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 10.3R1 | See Table 29 for a list of EX9200 routing policy and firewall filter features. |
Firewall filters and rate limiting | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
For a list of sup- ported firewall filter match conditions and actions, see Platform Support for Firewall Filter Match Conditions, Actions, and Action Modifiers on EX Series Switches. | ||||||||
Firewall filters on LAGs | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | Not sup- ported | 10.0R1 | |
Firewall filters on the loopback interface | 10.1R1 | 9.2R1 | 11.3R1 | 11.1R1 | 12.2R1 | 12.1R1 | 9.6R1 | |
For a list of sup- ported firewall filter match conditions and actions on a loopback interface, see Support for Match Conditions and Actions for Loopback Firewall Filters on Switches. | ||||||||
Firewall filters on the management interface | 11.3R1 | 10.4R1 | Not sup- ported | 10.4R1 | 12.2R1 | 12.1R1 | 10.4R1 | |
Firewall filters on the virtual management interface | – | 10.4R1 (EX4200 Virtual Chassis only) | Not sup- ported | – | – | – | – | |
Firewall filters with IPv6 | 11.3R1 | 10.1R1 | 12.3R1 | 12.1R1 | 12.2R1 | 12.1R1 | 10.3R1 | |
Policing | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Table 29: Routing Policy and Firewall Filters on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Access and access-internal routes | 12.3R2 |
Extension of numeric-range match conditions in firewall filters | 12.3R2 |
Aggregate policer support for different family address types configured on the same interface | 12.3R2 |
Authentication for BFD (MD5/SHA1) | 12.3R2 |
BGP multipath link-bandwidth attribute | 12.3R2 |
DHCP state persistence for DHCP relay agent | 12.3R2 |
Dynamic configuration support for routing policies | 12.3R2 |
Extended DHCP relay agent | 12.3R2 |
Filter-based forwarding to a specific outgoing interface or destination IP address | 12.3R2 |
Firewall filters within logical systems | 12.3R2 |
IEEE 802.1p priority match conditions for Layer 2 VPN firewall filters | 12.3R2 |
Filter-based forwarding to a specific outgoing interface or destination IP address | 12.3R2 |
Layer 2 Gigabit Ethernet logical interface extended policing support | 12.3R2 |
Layer 2 support for firewall filter match conditions | 12.3R2 |
Load balancing of VPLS traffic | 12.3R2 |
Option 60 support for extended DHCP relay agents | 12.3R2 |
Policers on physical interfaces | 12.3R2 |
Firewall filters feature support | 12.3R2 |
Support for policers that limit traffic on logical interfaces in ingress or egress directions | 12.3R2 |
Support for policers that rate-limit based on a percentage of physical port speed on an interface | 12.3R2 |
Support for the discard action for tricolor marking policers applied to firewall filters | 12.3R2 |
Support for the prefix-list match condition for firewall filters for the VPLS protocol family | 12.3R2 |
Support for enhanced policer statistics | 12.3R2 |
Support for MAC address validation | 12.3R2 |
Table 30: Spanning-Tree Protocols Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
BPDU protection for spanning-tree protocols | 10.1R1 | 9.1R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | See Table 31 for a list of EX9200 spanning-tree protocols features. |
BPDU filter | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | |
Distributed periodic packet management (PPM) for Spanning Tree Protocols | Not sup- ported | 12.3R1 | Not sup- ported | Not sup- ported | Not sup- ported | Not sup- ported | 12.3R1 | |
Loop protection for spanning-tree protocols | 10.1R1 | 9.1R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Root protection for spanning-tree protocols | 10.1R1 | 9.1R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Spanning tree:
| Not sup- ported | 10.2R1 | 12.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 10.2R1 | |
Spanning tree:
| 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Spanning tree:
| 10.1R1 | 9.4R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.6R1 |
Table 31: Spanning-Tree Protocols Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Spanning tree:
| 12.3R2 |
Root protection for spanning-tree protocols | 12.3R2 |
Loop protection for spanning-tree protocols | 12.3R2 |
Distributed periodic packet management (PPM) for Spanning Tree Protocols | 12.3R2 |
BPDU filter | 12.3R2 |
Table 32: System Management Features on Switches by Junos OS Release
Feature | EX2200 | EX3200, EX4200 | EX3300 | EX4500 | EX4550 | EX6200 | EX8200 | EX9200 |
|---|---|---|---|---|---|---|---|---|
Autoinstallation of configuration files | 10.1R1 | 9.4R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | Not sup- ported | See Table 33 for a list
of EX9200 system manage- |
Automatic software download | 10.1R1 | 9.6R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.6R1 | |
Automatic repair of corrupted partition when booting from alternate partition | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | |
Configuration rollback | 10.1R1 | 9.0R2 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R2 | 9.4R1 | |
Zero Touch Provisioning (EZ Touchless Provisioning using DHCP) | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | 12.2R1 | Not sup- ported | 12.2R1 | |
J-Web interface, for switch configuration and management | 10.1R1 (12.1R1 for EX2200-C switches) | 9.0R2 | 12.1R1 | 10.2R1 | 12.2R1 | 12.1R1 | 9.4R1 | |
Junos Space Service Now support | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | 12.3R1 | |
LCD panel management support | – | 9.0R1 | 11.3R1 | 10.2R1 | 12.2R1 | 11.3R1 | 9.4R1 | |
Online insertion and removal (OIR) of uplink modules | – | 10.0R1 | – | 11.1R1 | 12.2R1 | – | – |
Table 33: System Management Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Configuration rollback | 12.3R2 |
Table 34: User Interface and Configuration Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Device-initiated SSH connection (outbound SSH) | 12.3R2 |
Dynamic IPv6 filters | 12.3R2 |
Dynamic configuration of the switch advertisement protocol | 12.3R2 |
Dynamic profiles support by extended DHCP local server and extended DHCP relay agent | 12.3R2 |
Enhanced IPv6 statistics | 12.3R2 |
Extended DHCP local server | 12.3R2 |
IGMP dynamic profiles | 12.3R2 |
Extended DHCP local server | 12.3R2 |
Protection for device configuration | 12.3R2 |
RADIUS MSCHAPv2 protocol support for administrator authentication, password aging, and update | 12.3R2 |
Limit configuration command output | 12.3R2 |
Remote tracing | 12.3R2 |
Support for CLI edit mode wildcard range | 12.3R2 |
Support for configuring ARP aging time for a logical interface | 12.3R2 |
Support for configuring a proxy server for downloading licenses | 12.3R2 |
Support for configuring time-based user access | 12.3R2 |
Support for logical router system administrators | 12.3R2 |
Table 35: VPN Features on EX9200 Switches by Junos OS Release
Feature | Junos OS Release |
|---|---|
Aggregated Ethernet interfaces for VPLS routing instances | 12.3R2 |
BGP autodiscovery for LDP VPLS (FEC 129) | 12.3R2 |
Clearing MAC addresses for better convergence | 12.3R2 |
Configurable label block sizes for VPLS | 12.3R2 |
Disable TTL propagation behavior for the routes in a VRF routing instance | 12.3R2 |
EXP-based traffic classification for VPLS | 12.3R2 |
Enhanced show interface command for Layer 3 VPN functionality | 12.3R2 |
Expanded interface support for the vrf-table-label statement | 12.3R2 |
Extranet next-generation MVPN GRE tunnels for Layer 3 VPNs | 12.3R2 |
GRE tunnels for Layer 3 VPNs Ignore MTU mismatch on Layer 2 circuits Integrated routing and bridging support for inter-AS VPLS between BGP-signaled VPLS and LDP-signaled VPLS LDP-based VPLS Label allocation and substitution policy | 12.3R2 |
Ignore MTU mismatch on Layer 2 circuits | 12.3R2 |
Integrated routing and bridging support for inter-AS VPLS between BGP-signaled VPLS and LDP-signaled VPLS | 12.3R2 |
LDP-based VPLS | 12.3R2 |
Label allocation and substitution policy | 12.3R2 |
Layer 2 VPN multihoming | 12.3R2 |
Layer 3 VPN BGP routes and labels | 12.3R2 |
Layer 3 VPN localization | 12.3R2 |
Load balancing and IP header filtering for Layer 3 VPNs | 12.3R2 |
Local switching support for the ignore-encapsulation-mismatch statement | 12.3R2 |
Multipath load balancing for EBGP and IBGP VPNs | 12.3R2 |
Multiple logical trunk interfaces per physical interface | 12.3R2 |
Multiprotocol BGP-based multicast VPN | 12.3R2 |
NTP support for IPv4 VRF and IPv6 VRF | 12.3R2 |
Nonstop active routing support for Layer 3 VPNs | 12.3R2 |
PIM source-specific multicast (PIM-SSM) provider tunnel support added to Multiprotocol BGP-based multicast VPNs | 12.3R2 |
Point-to-multipoint LSP support for VPLS | 12.3R2 |
Point-to-multipoint LSP support for multicast VPNs | 12.3R2 |
Proxy BGP route target filtering | 12.3R2 |
Static VPLS | 12.3R2 |
Static route target filtering | 12.3R2 |
Support for autorp, BSR, PIM dense mode and mtrace for next-generation multicast VPNs | 12.3R2 |
VLAN range for Layer 2 VPN | 12.3R2 |
VPLS automatic site ID | 12.3R2 |
VPLS automatic site ID for nonstop active routing | 12.3R2 |
VPLS ping | 12.3R2 |
VPLS trunk interfaces | 12.3R2 |
eBGP and iBGP load-balancing support for MVPN and PIM | 12.3R2 |