From User Exec mode, use the following show commands to monitor and display the T3 interface,
T1 interface, and HDLC serial data channel information:
Monitor channelized T3 interfaces on a slot and port.
host1#show controllers t3 0/1
Monitor a T1 interface.
host1#show controllers t3 0/1:1
Monitor fractional T1 subchannels.
host1#show controllers t3 ft1
Monitor the state of the serial interface or a slot/port.
host1#show controllers t3 serial 0/1
Setting a Baseline
You can set a statistics baseline for serial interfaces,
subinterfaces, and/or circuits using the baseline interface
serial command. Use the delta keyword with the show commands to display
statistics with the baseline subtracted.
Displaying Counters and Time Intervals
Counters and time intervals are MIB statistics,
which are defined in the following specifications:
RFC 2495—Definitions of Managed Objects for the
DS1, E1, DS2 and E2 Interface Types (January 1999)
RFC 2496—Definitions of Managed Objects for the
DS3/E3 Interface Types (January 1999)
The show controllers t3 slot/port all command displays the following information:
T3 current interval counters—Counters for the current
interval
T3 last interval counters—Counters for the previous
interval
T3 24-hour total counters—Cumulative counters for
the last 24 hours or since the interface was started
The last 24 hours of 15-minute reporting intervals (96
intervals)
The show controllers t3 slot/port:channel all command displays the following information:
T1 current interval counters—Counters
for the current interval
T1 last interval counters—Counters for the previous
interval
T1 24-hour total counters—Cumulative counters for
the last 24 hours or since the interface was started
The last 24 hours of 15-minute reporting intervals (96
intervals)
Output Filtering
You can use the output filtering feature of the show command to include or exclude lines of output
based on a text string you specify. See Command Line Interface in JUNOSe System Basics Configuration Guide, for details.
baseline interface serial
Use to set a statistics baseline for serial interfaces.
The router implements the baseline by reading and storing
the statistics at the time the baseline is set and subtracting this
baseline whenever baseline-relative statistics are retrieved.
Use the optional delta keyword with the show
interfaces serial commands to view the baseline statistics.
Use to display data and MIB statistics for a T3 interface
or a T1 channel.
Use the brief keyword to display
the administrative and operational status of all configured T3 interfaces,
or to display abbreviated information for the specified T3 interface.
For definitions of the MIB statistics for a T3 interface,
see RFC 2496—Definitions of Managed Objects for the DS3/E3 Interface
Types (January 1999).
For definitions of the MIB statistics for a T1 channel,
see RFC 2495—Definitions of Managed Objects for the DS1, E1,
DS2 and E2 Interface Types (January 1999).
Field descriptions for T3 interface (T1 channel not specified)
Description—Text description or alias if configured
for the interface
ifAdminStatus—One of the following administrative
states of the interface:
ifAdminUp—Interface is administratively enabled
ifAdminDown—Interface is administratively disabled
ifAdminTesting—Interface is administratively configured
in a testing state
snmp trap link-status—Status
of SNMP trapping (enabled or disabled)
alarms detected—One of the following T3 alarms:
No alarm present—No alarms present on the line
Rcv RAI Failure—Remote device is sending a far end
alarm failure
Xmt RAI Failure—Local device is sending a far end
alarm failure
Rcv AIS—Remote device is sending an alarm indication
signal (AIS)
Xmt AIS—Local device is sending an AIS
Rcv LOF—Loss of one or more frames from the remote
end
Rcv LOS—Loss of signal at the local
end
Undefined line status—Indicates that the line is
in an undefined state
Note:
The alarms detected field does not appear for interfaces that
you disabled in the software.
framing—Type of framing format
line code—Type of line code format
clock source—Type of clock source
cable length—Cable length, in feet
Loopback—State of loopback for the controller: enabled
or disabled. If loopback is enabled, one of the following states is
displayed:
Diagnostic—Loops the data back toward the router
and sends an AIS toward the network
Payload—Loops the data toward the network after
the framer has processed the data
Line—Loops the data toward the network before the
data reaches the framer
MDL Transmit Path—Status of path transmission: active
or not active
MDL Transmit Test-Signal—Status of test signal:
active or not active
MDL Transmit Idle-Signal—Status of idle signal:
active or not active
Equipment Identification Code—eic string for MDL
Line Identification Code—lic string for MDL
Frame Identification Code—fic string for MDL
Unit Identification Code—unit string for MDL
Facility Identification Code—pfi string for MDL
Port Code—port string for MDL
Generator Number—generator string for MDL
BERT test—Number of current test and total number
of tests
Test interval—Length of the BERT test
status—Sync (controller is synchronized with remote
device) or NoSync (controller is not synchronized with remote device)
Sync count—Number of times the pattern detector
synchronized with the incoming data pattern
Received bit count—Number of bits received
Error bit count—Number of bits with errors
Number of valid intervals—Number of 15-minute intervals
since the line module was last powered on or reset
Time elapse in current interval—Reported in 15-second
intervals
P-bit errored seconds—Number of errored seconds
encountered by a T3 in the current interval
P-bit severely errored seconds—Number of severely
errored seconds encountered by a T3 in the current interval
Severely errored frame seconds—Number of severely
errored framing seconds encountered by a T3 in the current interval
Unavailable seconds—Number of unavailable seconds
encountered by a T3 in the current interval
Line code violations—Number of line code violations
encountered by a T3 in the current interval
P-bit coding violations—Number of coding violations
encountered by a T3 in the current interval
Line errored seconds—Number of line errored seconds
encountered by a T3 in the current interval
C-bit coding violations—Number of C-bit coding violations
encountered by a T3 in the current interval
C-bit errored seconds—Number of C-bit errored seconds
encountered by a T3 in the current interval
C-bit severely errored seconds—Number of C-bit severely
errored seconds encountered by a T3 in the current interval
Example 1—In this example, a T3 interface is specified.
host1#show controllers t3 2/0
DS3 2/0
Description: toronto ct3 interface
ifAdminStatus = ifAdminDown
snmp trap link-status = enabled
No alarms detected
Framing is C-BIT, Line Code is B3ZS, Clock Source is Line
Cable Length is 0 ft
Loopback Disabled
MDL Transmit Path is not active
MDL Transmit Test-Signal is active
MDL Transmit Idle-Signal is not active
Equipment Identification Code is ERX-1400
Line Identification Code is Bldg 10
Frame Identification Code is null string
Unit Identification Code is 080001
Facility Identification Code is Site 25
Port Code is Port 0800
Generator Number is null string
Number of valid interval - 96
Time elapse in current interval - 861
Ds3 Current Interval Counters
P-bit errored seconds = 0
P-bit severely errored seconds = 0
Severely errored frame seconds = 0
Unavailable seconds = 0
Line code violations = 0
P-bit coding violations = 0
Line errored seconds = 0
C-bit coding violations = 0
C-bit errored seconds = 0
C-bit severely errored seconds = 0
Ds3 Last Interval Counters
P-bit errored seconds = 0
P-bit severely errored seconds = 0
Severely errored frame seconds = 0
Unavailable seconds = 0
Line code violations = 0
P-bit coding violations = 0
Line errored seconds = 0
C-bit coding violations = 0
C-bit errored seconds = 0
C-bit severely errored seconds = 0
Ds3 24 Hour Total Counters
P-bit errored seconds = 0
P-bit severely errored seconds = 0
Severely errored frame seconds = 0
Unavailable seconds = 0
Line code violations = 0
P-bit coding violations = 0
Line errored seconds = 0
C-bit coding violations = 0
C-bit errored seconds = 0
C-bit severely errored seconds = 0
Example 2—In this example, the brief keyword is specified.
host1#show controllers t3 brief
Interfaces ifAdminStatus OperationalStatus
5/0(channelized) up up
5/1(channelized) up up
5/2(channelized) up down
5/3(channelized) down down
5/4(channelized) down down
5/5(channelized) down down
5/6(channelized) down down
5/7(channelized) down down
5/8(channelized) down down
5/9(channelized) down down
5/10(channelized) down down
5/11(channelized) down down
3/0(channelized) down down
3/1(channelized) down down
3/2(channelized) down down
4/0:1/1(unchannelized) up down
4/2:1/1(channelized) up lowerLayerDown
Field descriptions for a T1 channel
Description—Text description or alias if configured
for the interface
ifOperStatus—Physical state of the interface:
ifOperDown—Interface is not functioning
ifOperLowerLayerDown—Lower layer in the interface
stack is not functioning
ifOperNotPresent—Module has been removed from the
chassis
ifOperTesting—Interface is being tested
ifOperUp—Interface is functioning
Yellow Alarm detection—Status of yellow alarm detection:
active or not active
Yellow Alarm generation—Status of yellow alarm generation:
active or not active
snmp trap link-status—Status of SNMP trapping (enabled
or disabled)
Framing—Type of framing format
Clock source—Type of clock source
Loopback state—Type of loopback (if enabled) and
status: enabled or disabled
Last remote loopback request sent—None or deactivate
FDL—Status of FDL: standard configured or not configured
FDL Transmit Path—Status of path transmission: active
or not active
FDL Transmit Idle-Signal—Status of idle signal:
active or not active
FDL Transmit Test-Signal—Status of test signal:
active or not active
Equipment Identification Code—eic string for FDL
Line Identification Code—lic string for FDL
Frame Identification Code—fic string for FDL
Unit Identification Code—unit string for FDL
Facility Identification Code—pfi string for FDL
Port Code—port string for FDL
Generator Number—generator string for FDL
BERT test—Number of current test and total number
of tests
Test interval—Length of the BERT test
status—Sync (controller is synchronized with remote
device) or NoSync (controller is not synchronized with remote device)
Sync count—Number of times the pattern detector
synchronized with the incoming data pattern
Received bit count—Number of bits received
Error bit count—Number of bits with errors
Number of valid intervals—Number of 15-minute intervals
since the line module was last powered on or reset
Time elapse in current interval—Statistics are reported
in 15-minute intervals
Errored seconds—Number of errored seconds encountered
by a T1 in the current interval
Severely errored seconds—Number of severely errored
seconds encountered by a T1 in the current interval
Severely errored frame seconds—Number of severely
errored framing seconds encountered by a T1 in the current interval
Unavailable seconds—Number of unavailable seconds
encountered by a T1 in the current interval
Clock slip seconds—Number of clock slips encountered
by a T1 in the current interval
Path code violations—Number of coding violations
encountered by a T1 in the current interval
Line errored seconds—Number of line errored seconds
encountered by a T1 in the current interval
Bursty errored seconds—Number of bursty errored
seconds encountered by a T1 in the current interval
Degraded minutes—Number of minutes that a T1 line
is degraded
Line code violations—Number of line code violations
encountered by a T1 in the current interval
Example 1—In this example, a T1 channel
and the brief keyword are specified.
host1#show controllers t1 2/0:1 brief
DS3 2/0:1
ifOperStatus = ifOperUp
Yellow Alarm detection is active
Yellow Alarm generation is active
snmp trap link-status = disabled
Framing is D4, Line Code is Ami, Clock Source is Internal - Module Allocated Ds0 time slot map = 0x0
Loopback Enabled - Diagnostic
Last Remote Loopback Request Sent - Deactivate
FDL is not configured
FDL Transmit Path-Id is not active
FDL Transmit Test-Signal is not active
FDL Transmit Idle-Signal is not active
Equipment Identification Code is the null string
Line Identification Code is the null string
Frame Identification Code is the null string
Unit Identification Code is the null string
Facility Identification Code is the null string
Port Code is the null string
Generator Number is the null string
BERT test - 2 in 23
Test Interval 1 minute(s), Complete
Sync count = 1
Received bit count = 92148912
Error bit count = 17
Number of valid interval - 90
Time elapse in current interval - 580
Example 2—In this example, the brief keyword is specified for all T1 channels.
host1#show controllers t1 brief
Interfaces ifAdminStatus OperationalStatus
5/0:1(framed) up lowerLayerDown
5/0:2(framed) up lowerLayerDown
5/0:3(framed) up lowerLayerDown
5/0:4(framed) up lowerLayerDown
5/0:5(framed) up lowerLayerDown
5/0:6(framed) up lowerLayerDown
...
5/2:26(framed) up lowerLayerDown
5/2:27(framed) up lowerLayerDown
5/2:28(framed) up lowerLayerDown
Example 3—In this example, a T1 channel is specified.
host1#show controllers t1 1/0:1
DS1 1/0:1
Description: toronto t1 channel
ifOperStatus = ifOperUp
Yellow Alarm detection is active
Yellow Alarm generation is active
snmp trap link-status = disabled
Framing is D4, Line Code is Ami, Clock Source is Internal - Module Allocated Ds0 time slot map = 0x0
Last Remote Loopback Request Sent - Deactivate
FDL is not configured
FDL Transmit Path-Id is not active
FDL Transmit Test-Signal is not active
FDL Transmit Idle-Signal is not active
Equipment Identification Code is the null string
Line Identification Code is the null string
Frame Identification Code is the null string
Unit Identification Code is the null string
Facility Identification Code is the null string
Port Code is the null string
Generator Number is the null string
BERT test - 2 in 23
Test Interval 1 minute(s), Complete
Sync count = 1
Received bit count = 92148912
Error bit count = 17
Number of valid interval - 90
Time elapse in current interval - 580
Use to display MIB statistics for the remote end of a
channelized T3 interface configured for MDL or for the remote end
of a T1 channel configured for FDL.
Specify the all option to display detailed information
for all 15-minute intervals.
For definitions of the MIB statistics for a T3 interface,
see RFC 2496—Definitions of Managed Objects for the DS3/E3 Interface
Types (January 1999).
For definitions of the MIB statistics for a T1 channel,
see RFC 2495—Definitions of Managed Objects for the DS1, E1,
DS2 and E2 Interface Types (January 1999).
Field descriptions for a T3 interface
Far End MDL Carrier bit—Status of MDL configuration
on remote device connected to T3 interface
set—MDL is configured for carrier mode
not set—MDL is not configured for carrier mode
Far End Equipment Identification Code—eic string
sent by remote device for MDL
Far End Line Identification Code—lic string sent
by remote device for MDL
Far End Frame Identification Code—fic string sent
by remote device for MDL
Far End Unit Identification Code—unit string sent
by remote device for MDL
Far End Facility Identification Code—pfi string
sent by remote device for MDL
Far End Generator Number—generator string sent by
remote device for MDL
Far End Port Number—port string sent by remote device
for MDL
Number of valid intervals—Number of 15-minute intervals
since the line module was last powered on or reset
Time elapse in current interval—Number of seconds
that have passed in the 15-minute (900-second) interval
C-bit errored seconds—Number of C-bit errored seconds
encountered by a T3 in the current interval
C-bit severely errored seconds—Number of C-bit severely
errored seconds encountered by a T3 in the current interval
C-bit coding violations—Number of C-bit coding violations
encountered by a T3 in the current interval
Unavailable seconds—Number of unavailable seconds
encountered by a T3 in the current interval
Invalid seconds—Number of seconds when statistics
were not collected
Example—In this example, a T3 interface is specified.
host1#show controllers t3 5/0 remote
Far End MDL Carrier bit is not set
Far End Equipment Identification Code is the null string
Far End Line Identification Code is the null string
Far End Frame Identification Code is the null string
Far End Unit Identification Code is the null string
Far End Facility Identification Code is the null string
Far End Generator Number is the null string
Far End Port Number is the null string
Number of valid interval - 3
Time elapse in current interval - 756
Number of valid intervals—Number of 15-minute intervals
since the line module was last powered on or reset
Time elapse in current interval—Number of seconds
that have passed in the 15-minute (900-second) interval
Far End FDL Carrier bit—Status of FDL configuration
on remote device connected to T1 channel
set—FDL is configured for carrier mode
not set—FDL is not configured for carrier mode
Far End Equipment Identification Code—eic string
sent by remote device for FDL
Far End Line Identification Code—lic string sent
by remote device for FDL
Far End Frame Identification Code—fic string sent
by remote device for FDL
Far End Unit Identification Code—unit string sent
by remote device for FDL
Far End Facility Identification Code—pfi string
sent by remote device for FDL
Far End Generator Number—generator string sent by
remote device for FDL
Far End Port Number—port string sent by remote device
for FDL
Errored seconds—Number of errored seconds encountered
by a T1 in the current interval
Severely errored seconds—Number of severely errored
seconds encountered by a T1 in the current interval
Severely errored frame seconds—Number of severely
errored framing seconds encountered by a T1 in the current interval
Unavailable seconds—Number of unavailable seconds
encountered by a T1 in the current interval
Clock slip seconds—Number of clock slips encountered
by a T1 in the current interval
Path code violations—Number of coding violations
encountered by a T1 in the current interval
Line errored seconds—Number of line errored seconds
encountered by a T1 in the current interval
Bursty errored seconds—Number of bursty errored
seconds encountered by a T1 in the current interval
Degraded minutes—Number of minutes that a T1 line
is degraded
Example—In this example, a T1 channel is specified.
host1#show controllers t1 10/1:1 remote
DS1 10/1:1
Number of valid interval - 0
Time elapse in current interval - 0
Far End FDL Carrier bit is not set
Far End Equipment Identification Code is the null string
Far End Line Identification Code is the null string
Far End Frame Identification Code is the null string
Far End Unit Identification Code is the null string
Far End Facility Identification Code is the null string
Far End Port Number is the null string
Far End Generator Number is the null string
