To display information about networks for all address
families or for a specific address family other than the L2VPN address
family and the route-target address family:
To display information for networks associated with only the
L2VPN address family:
show ip bgp { l2vpn all | l2vpn vpls vplsName | l2vpn vpws vpwsName } [ site-id siteId block-offset blockOffset ]
[ fields fieldOptions ] [ filter ]
To display information for networks associated with only the
route-target address family:
show ip bgp route-target signaling rtfPrefix [ longer-prefixes ] [ fields fieldOptions ] [ filter ]
Release Information
Command introduced before JUNOSe Release
7.1.0. l2vpn and all keywords added in JUNOSe Release 7.1.0. vpls keyword and vplsName variable added in JUNOSe Release 7.1.0. site-id keyword and siteId variable
added in JUNOSe Release 7.1.0. block-offset keyword and blockOffset variable added in JUNOSe
Release 7.1.0. vpws keyword and vpwsName variable added in JUNOSe
Release 8.1.0. route-target signaling keywords and rtMemNlri variable added in JUNOSe
Release 8.2.0. rtMemNlri variable replaced by rtfPrefix variable in
JUNOSe Release 9.1.0.
Description
Displays filtered information about a specified
network, or all networks, in the BGP routing table associated with
a specified address family or all address families. Only those fields
that you specify are displayed, except that the prefix field is always
displayed. Default fields can be set with the default-fields
route command.
Options
ipv4 unicast—Specifies the IPv4 unicast address
family and routing table; the default option
ipv4 multicast—Specifies the IPv4 multicast address
family and routing table
vpnv4 all—Specifies the IPv4 VPN address family
and all IPv4 VPN routing and forwarding instances
vpvn4 vrf vrfName—Specifies
the IPv4 VPN address family and only the IPv4 VPN routing and forwarding
instance with the name vrfName
network—IP address for which
the best matching route is displayed; if no network is specified,
displays the fields for all networks
networkMask—Address mask to
be applied to the network address
longer-prefixes—Displays all routes with a prefix
that is equal to or more specific than the specified prefix
l2vpn all—Specifies all VPLS and VPWS instances
in the L2VPN address family
l2vpn vpls vplsName—Specifies
the VPLS instance with the name vplsName
l2vpn vpws vpwsName—Specifies
the VPWS instance with the name vpwsName
siteId—Numerical identifier
for the site; must be an unsigned 16-bit integer greater than zero
that is unique across the VPLS domain
blockOffset—Integer in the
range 1–65535 that identifies a block offset for which information
is displayed
route-target signaling—Specifies the route-target
address family
rtfPrefix—Prefix representing
the route-target membership NLRI (RT-MEM-NLRI), in the format asNumber:extendedCommunity/prefixLength (for
example, 320:320:524/36) where:
asNumber—AS number for origin
of route target information, in the range 1–4294967295
extendedCommunity—Two-part
number in the format number1:number2 that identifies an extended community of VPNs, in the format number1:number2, where:
number1—Autonomous system
(AS) number, in the range 1–4294967295, or an IP address
number2—Unique integer, in
the range 1–4294967295; 32 bits if number1 is a 16-bit AS number; 16 bits if number1 is an IP address or a 32-bit AS number
prefixLength—Number that specifies
the length of the route prefix, in the range 32–96
fields—Displays only the specified fields; the display
order of the fields is hard-coded and not affected by the order in
which you enter them
fieldOptions—Fields to be
displayed, in the format all | [ afi | aggregator |
as-path | atomic-aggregate | best | clusters | communities | extended-communities
| imported | intro | in-label | loc-pref | med | next-hop | next-hop-cost
| origin | originator-id | out-label | peer | peer-type | rd | safi
| stale | unknown-types | weight ]*
all—All available information; not recommended,
because this information for each network does not fit on a single
line and is difficult to read
afi—Address family identifier
aggregator—AS number and IP address of aggregator
as-path—AS path through which this route bas been
advertised
atomic-aggregate—Whether the atomic aggregate attribute
is present
best—Whether this is the best route for the prefix
clusters—List of cluster IDs through which the route
has been advertised
communities—Community number associated with the
route
extended-communities—Extended community
imported—Whether the route was imported
intro—Introductory information about the state of
various BGP attributes; this information is displayed only if you
specify this keyword
in-label—MPLS label for the route; the label received
with incoming MPLS frames; typically, but not always, this is the
label advertised to MP-BGP peers
loc-pref—Local preference for the route
med—Multiexit discriminator for the route
next-hop—IP address of the next router that is used
when forwarding a packet to the destination network
next-hop-cost—Whether the indirect next hop of the
route is unreachable, if not, displays IGP cost to the indirect next
hop
origin—Origin of the route
originator-id—Router ID of the router in the local
AS that originated the route
out-label—MPLS label for the route; the label sent
with outgoing MPLS frames; also the label received from MP-BGP peer;
typically, but not always, this is the label received from MP-BGP
peers
peer—IP address of BGP peer from which route was
learned
peer-type—Type of BGP peer: internal, external,
or confederation
rd—Route distinguisher
safi—Subsequent address family identifier
stale—Route that has gone stale due to peer restart
unknown-types—Attribute codes for unknown path attributes
weight—Weight of the route
*—Indicates that one or more parameters can be repeated
multiple times in a list in the command line
