From Interface Configuration or Subinterface Configuration
mode, creates a PVC on an ATM interface. The no version removes the specified PVC.
From Profile Configuration mode, applies encapsulation, traffic-shaping,
and OAM parameters to the range of PVCs configured on a static ATM
AAL5 interface for use by a dynamic ATM 1483 subinterface. The no version restores the default service type, UBR,
on the VC range.
Note:
The optional peak, average, and burst parameters configure traffic-shaping
parameters for the circuit. The allowable traffic-shaping features
and range specifications depend on the line module capabilities.
Options
vcd—Virtual circuit descriptor
that is an identifier for the VC in other commands; in the range 1–2147483647
vpi—Virtual path identifier
of this PVC. The allowable numeric range depends on the line module
capabilities and current configuration. The VPI and VCI cannot both
be set to 0; if one is 0, the other cannot be 0.
vci—Virtual circuit identifier
of this PVC. The allowable numeric range depends on the line module
capabilities and current configuration. The VPI and VCI cannot both
be set to 0; if one is 0, the other cannot be 0.
encapsulation—Available options
differ for ATM interfaces and dynamic ATM 1483 subinterfaces, as follows:
For PVCs created on ATM interfaces:
aal5all—Causes the router to pass through all ATM
AAL5 traffic without interpreting it; supported for ATM layer 2 services
over MPLS
aal0—Causes the router to receive raw ATM cells
on this circuit and forward the cells without performing AAL5 packet
reassembly; supported for ATM layer 2 services over MPLS
aal5snap—LLC encapsulated circuit; LLC/SNAP header
precedes the protocol datagram
aal5mux ip—VC-based multiplexed circuit used for
IP only
aal5autoconfig—Enables autodetection of the 1483
encapsulation (LLC/SNAP or VC multiplexed)
ilmi—Integrated local management interface encapsulation
For PVCs created on dynamic ATM 1483 subinterfaces:
aal5snap—LLC encapsulated circuit; LLC/SNAP header
precedes the protocol datagram
aal5mux ip—VC-based multiplexed circuit used for
IP only
aal5autoconfig—Enables autodetection of the 1483
encapsulation (LLC/SNAP or VC multiplexed)
cbr—Constant bit rate in Kbps
peak—PCR in Kbps
average—Average rate in Kbps;
also referred to as SCR
burst—Length in cells of the
burst; also referred to as MBS
rt—Selects VBR-RT as the service type; the default
type is VBR-NRT. You can select rt only
if you set the peak, average, and burst parameters.
oam—Enables generation of OAM F5 loopback cells
on this circuit. This option enables VC integrity features that affect
the operational state of the ATM PVC. You can use the oam keyword only if you specify the aal5snap, aal5autoconfig, or aal5mux
ip encapsulation type.
seconds—Time interval in the
range 1–600 seconds between transmissions of OAM F5 end-to-end
loopback cells for VC connectivity verification.
inArp—Enables Inverse ARP. You can use the inArp keyword only if you specify the aal5snap encapsulation type.
minutes—Inverse ARP refresh
rate in minutes; 15 minutes is the default
cc—Enables CC cells on the PVC; you can enable CC
cells only on data circuits, not on control circuits, such as ILMI
or signaling circuits
segment—Opens an OAM CC segment cell flow
end-to-end—Opens an OAM CC end-to-end cell flow
sink—Enables this VC as a sink point (cell receiver)
source—Enables this VC as the source point (cell
generator)
both—Enables this VC as both a sink point and a
source point
Configuring an MPLS Pseudowire with VCC Cell
Relay Encapsulation, Configuring Local ATM Cross-Connects
with AAL5 Encapsulation, and Configuring MPLS
LSPs for L2VPNs in the JUNOSe BGP and MPLS Configuration Guide
