Persistent interface error statistics indicate that you need to open a case with JTAC.
To check the local interface for error statistics, use the following JUNOS CLI operational mode command:
Sample Output
user@host# show interfaces t1-2/1/0:20
extensive Physical interface: t1-2/1/0:20, Enabled, Physical link is Up
Interface index: 210, SNMP ifIndex: 173, Generation: 93
Link-level type: Cisco-HDLC, MTU: 1504, Clocking: Internal, Speed: T1, Loopback: Local, FCS: 16,
Mode: C/Bit parity, Framing: ESF
Device flags : Present Running
Interface flags: Point-To-Point SNMP-Traps
Link flags : No-Keepalives
Hold-times : Up 0 ms, Down 0 ms
CoS queues : 4 supported
Last flapped : 2004-05-20 21:46:27 UTC (00:26:47 ago)
Statistics last cleared: 2004-05-20 22:12:03 UTC (00:01:11 ago)
Traffic statistics:
Input bytes : 88680 27640 bps
Output bytes : 88680 27640 bps
Input packets: 1010 39 pps
Output packets: 1010 39 pps
Input errors:
Errors: 0, Drops: 0, Framing errors: 0, Policed discards: 0, L3 incompletes: 0, L2 channel errors: 0,
L2 mismatch timeouts: 0, HS link CRC errors: 0, SRAM errors: 0
Output errors:
Carrier transitions: 0, Errors: 0, Drops: 0, Aged packets: 0
DS1 alarms : None
DS3 alarms : None
DS1 defects : None
DS3 defects : None
T1 media: Seconds Count State
SEF 0 0 OK
BEE 0 0 OK
AIS 0 0 OK
LOF 0 0 OK
LOS 0 0 OK
YELLOW 0 0 OK
BPV 0 0
EXZ 0 0
LCV 0 0
PCV 0 0
CS 0 0
LES 0
ES 0
SES 0
SEFS 0
BES 0
UAS 0
DS3 media: Seconds Count State
PLL Lock 0 0 OK
Reframing 0 0 OK
AIS 0 0 OK
LOF 0 0 OK
LOS 0 0 OK
IDLE 0 0 OK
YELLOW 0 0 OK
BPV 0 0
EXZ 0 0
LCV 0 0
PCV 0 0
CCV 0 0
LES 0
PES 0
PSES 0
CES 0
CSES 0
SEFS 0
UAS 0
Interface transmit queues:
B/W WRR Packets Bytes Drops Errors
Queue0 95 95 0 0 0 0
Queue1 5 5 1010 88680 0 0
HDLC configuration:
Giant threshold: 1514, Runt threshold: 3
Timeslots : All active
Line encoding: B8ZS, Byte encoding: Nx64K, Data inversion: Disabled, Idle cycle flag: flags,
Start end flag: shared
DS-3 BERT configuration:
BERT time period: 10 seconds, Elapsed: 0 seconds
Algorithm: 2^3 - 1, Pseudorandom (1), Induced error rate: 10e-0
DS1 BERT configuration:
BERT time period: 10 seconds, Elapsed: 0 seconds
Induced Error rate: 10e-0, Algorithm: 2^15 - 1, O.151, Pseudorandom (9)
Packet Forwarding Engine configuration:
Destination slot: 2, PLP byte: 2 (0x14)
CoS transmit queue Bandwidth Buffer Priority Limit
% bps % bytes
0 best-effort 95 1459200 95 0 low none
3 network-control 5 76800 5 0 low none
Logical interface t1-2/1/0:20.0 (Index 74) (SNMP ifIndex 213) (Generation 14)
Flags: Point-To-Point SNMP-Traps Encapsulation: Cisco-HDLC
Protocol inet, MTU: 1500, Generation: 24, Route table: 0
Flags: None
Addresses, Flags: Is-Preferred Is-Primary
Destination: 10.10.1.1, Local: 10.10.1.2, Broadcast: Unspecified, Generation: 24
Meaning
Check for any error statistics that may appear in the output. There should not be any input or output errors. If there are any persistent input or output errors, open a case with JTAC at support@juniper.net, or at 1-888-314-JTAC (within the United States) or 1-408-745-9500 (from outside the United States).