Errata in Documentation for JUNOS Software Release 9.5 for J-series Services Routers

Chassis Clustering

• The “Setting the Node ID and Cluster ID” and “Active/Passive Chassis Cluster Scenario” sections in the JUNOS Software Security Configuration Guide incorrectly show command syntax as the following:

  set chassis cluster node 0 cluster-id 1

  set chassis cluster node 1 cluster-id 1 reboot

  The command syntax should be as follows:

  set chassis cluster cluster-id 1 node 0

  set chassis cluster cluster-id 1 node 1 reboot

CLI

• Page 976 of the JUNOS Software CLI Reference Guide displays the “show security alg status” title when it should display the “show security alg sip transactions” title. The information for Syntax, Release Information, Description, and Options is also incorrect. The correct information is provided below.

  Syntax—show security alg sip transactions<node (node-id | all | local | primary)>

  Release information—Command modified in Release 9.2 of JUNOS software; node options added in Release 9.0 of JUNOS software.

  Description—Display information about Session Initiation Protocol (SIP) Application Layer Gateway (ALG) transactions.

  This command is supported on J-series and SRX-series devices.

  Options

  • none—Display all SIP ALG transactions.
  • node—(Optional) For chassis cluster configurations, display SIP transactions on a specific node (device) in the cluster.
  • node-id—Identification number of the node. It can be 0 or 1.
  • all—Display information about all nodes.
  • local—Display information about the local node.
  • primary—Display information about the primary node.

DLSw

• The JUNOS Software Interfaces and Routing Configuration Guide incorrectly states that the data link switching (DLSw) protocol is supported in this release. DLSw support ended in JUNOS Release 9.3.

Intrusion Detection and Prevention (IDP)

• In the JUNOS Software Security Configuration Guide, the following information in the "Verifying the Policy Compilation and Load Status" section is incorrect:
  • The text does not indicate that the log file must be created first.
  • The path for the log file is incorrect.

  Note the following correct information:

  • Create the log file first by entering set security idp traceoptions file idpd. You can then set flags by entering set security idp traceoptions flag all.
  • The correct path for the idpd log file is /var/log, not /var/db

J-Web

• J-Web Pages for Stateless Firewall Filters

  There is no documentation describing the J-Web pages for stateless firewall filters. To find these pages in J-Web, go to Configuration>Firewall Filters, then select IPv4 Firewall Filters or IPv6 Firewall Filters. After configuring filters, select Assign to Interfaces to assign your configured filters to interfaces.

PIM

The J2300, J4300, and J6300 Services Router Getting Started Guide incorrectly states that 1000Base-LH SFP (JX-SFP-1GE-LH) is not supported. This SFP is supported.

Screens

• The following guide contains incorrect screen configuration instructions:

  • JUNOS Software Design and Implementation Guide, “Implementing Firewall Deployments for Branch Offices” chapter
  Examples throughout the guide describe how to configure screen options using the set security screen screen-name CLI statements. Instead, you should use the set security screen ids-option screen-name CLI statements. All screen configuration options are located in the [set security screen ids-option screen-name] level of the configuration hierarchy.

Related Topics

• New Features in JUNOS Software Release 9.5 for J-series Services Routers
• Known Limitations in JUNOS Software Release 9.5 for J-series Services Routers
• Changes in Default Behavior and Syntax
• Issues in JUNOS Software Release 9.5 for J-series Services Routers
• Hardware Requirements for JUNOS Software Release 9.5 for J-series Services Routers
• Upgrade and Downgrade Instructions for JUNOS Software Release 9.5 for J-series Services Routers