Miscellaneous Commands for a Routing Matrix
There are a variety of other useful commands you can use when maintaining a routing matrix.
- To display the location of routing matrix components and
convert FPCs from T640 routing node local numbering to routing matrix
global numbering, issue the show chassis location fpc command
on the TX Matrix platform:
user@router> show chassis location fpcGlobal FPC LCC Local FPC 1 0 1 2 0 2 3 0 3 16 2 0 17 2 1 19 2 3 - To check the status of the SIB connection between the
TX Matrix platform and T640 routing nodes, issue the show chassis
fabric topology command on the TX Matrix platform. All values
for each available T640 routing node (LCC) should be in the UP state. In the following excerpt of output for this command, a routing
matrix that contains only LCCs 0 and 2 shows only
these two T640 routing nodes as being UP:
LCC0_SIB-L0_F0,03->SIB-S0_F0,00 UP LCC1_SIB-L0_F0,03->SIB-S0_F0,01 RESET LCC2_SIB-L0_F0,03->SIB-S0_F0,02 UP LCC3_SIB-L0_F0,03->SIB-S0_F0,03 RESET
- To verify that the Ethernet links between the TX Matrix
platform and the T640 routing node control boards are operational,
issue the show chassis ethernet-switch command on the TX
Matrix platform:
user@router> show chassis ethernet-switchscc-re0: -------------------------------------------------------------------------- Link is good on FE port 4 connected to device: LCC0 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 6 connected to device: LCC2 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 8 connected to device: SPMB Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on GE port 13 connected to device: Other RE Speed is 1000Mb Duplex is full Autonegotiate is Enabled lcc0-re0: -------------------------------------------------------------------------- Link is good on FE port 1 connected to device: FPC1 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 2 connected to device: FPC2 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 3 connected to device: FPC3 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 8 connected to device: SPMB Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 10 connected to device: SCC Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on GE port 13 connected to device: Other RE Speed is 100Mb Duplex is full Autonegotiate is Enabled lcc2-re0: -------------------------------------------------------------------------- Link is good on FE port 0 connected to device: FPC0 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 1 connected to device: FPC1 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 3 connected to device: FPC3 Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 8 connected to device: SPMB Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on FE port 10 connected to device: SCC Speed is 100Mb Duplex is full Autonegotiate is Enabled Link is good on GE port 13 connected to device: Other RE Speed is 100Mb Duplex is full Autonegotiate is Enabled
