routing-table-name

Name of the routing table (for example, inet.0).

number destinations

Number of destinations for which there are routes in the routing table.

number routes

Number of routes in the routing table and total number of routes in the following states:

• active (routes that are active).
• holddown (routes that are in the pending state before being declared inactive).
• hidden (routes that are not used because of a routing policy).

destination-prefix

Route destination (for example:10.0.0.1/24). Sometimes the route information is presented in another format, such as:

• MPLS-label (for example, 80001).
• interface-name (for example, ge-1/0/2).
• neighbor-address:control-word-status:encapsulation type:vc-id :source (Layer 2 circuit only; for example, 10.1.1.195:NoCtrlWord:1:1:Local/96):
  • neighbor-address—Address of the neighbor.
  • control-word-status—Whether the use of the control word has been negotiated for this virtual circuit: NoCtrlWord or CtrlWord.
  • encapsulation type— Type of encapsulation, represented by a number: (1) Frame Relay DLCI, (2) ATM AAL5 VCC transport, (3) ATM transparent cell transport, (4) Ethernet, (5) VLAN Ethernet, (6) HDLC, (7) PPP, (8) ATM VCC cell transport, (10) ATM VPC cell transport
  • vc-id—Virtual circuit identifier.
• source—Source of the advertisement: Local or Remote.

[protocol, preference ]

Protocol from which the route was learned and the preference value for the route.

• +—A plus sign indicates the active route, which is the route installed from the routing table into the forwarding table.
• - —A hyphen indicates the last active route.
• *—An asterisk indicates that the route is both the active and the last active route. An asterisk before a to line indicates the best subpath to the route.

In every routing metric except for the BGP LocalPref attribute, a lesser value is preferred. In order to use common comparison routines, JUNOS software stores the 1's complement of the LocalPref value in the Preference2 field. For example, if the LocalPref value for Route 1 is 100, the Preference2 value is -101. If the LocalPref value for Route 2 is 155, the Preference2 value is -156. Route 2 is preferred because it has a higher LocalPref value and a lower Preference2 value.

weeks:days hours:minutes:seconds

How long the route been known (for example, 2w4d 13:11:14, or 2 weeks, 4 days, 13 hours, 11 minutes and 14 seconds).

metric

Metric associated with the route.

localpref

Local preference value included in the route.

from

Interface from which the route was received.

AS path

AS path through which the route was learned. The letters at the end of the AS path indicate the path origin, providing an indication of the state of the route at the point at which the AS path was originated:

• I—IGP.
• E—EGP.
• ?—Incomplete; typically, the AS path was aggregated.

When AS path numbers are included in the route, the format is as follows:

• [ ]—Brackets enclose the local AS number associated with the AS path if more than one AS number is configured on the router, or if AS path prepending is configured.
• { }—Braces enclose AS sets, which are groups of AS numbers in which the order does not matter. A set commonly results from route aggregation. The numbers in each AS set are displayed in ascending order.
• ( )—Parentheses enclose a confederation.
• ( [ ] )—Parentheses and brackets enclose a confederation set.

to

Next hop to the destination. An angle bracket (>) indicates that the route is the selected route.

via

Interface used to reach the next hop. If there is more than one interface available to the next hop, the interface that is actually used is followed by the word Selected. This field can also contain the following information:

• Weight—Value used to distinguish primary, secondary, and fast reroute backup routes. Weight information is available when Multiprotocol Label Switching (MPLS) label-switched path (LSP) link protection, node-link protection, or fast reroute is enabled, or when the standby state is enabled for secondary paths. A lower weight value is preferred. Among routes with the same weight value, load balancing is possible.
• Balance—Balance coefficient indicating how traffic of unequal cost is distributed among next hops when a router is performing unequal-cost load balancing. This information is available when you enable Border Gateway Protocol (BGP) multipath load balancing.
• lsp-path-name—Name of the label-switched path (LSP) used to reach the next hop.
• label-action—MPLS label and operation occurring at the next hop. The operation can be pop (where a label is removed from the top of the stack), push (where another label is added to the label stack), or swap (where a label is replaced by another label).