TechLibrary

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Miscellaneous Commands for a Routing Matrix with a TX Matrix Router

    There are a variety of other useful commands you can use when maintaining a routing matrix with a TX Matrix router.

    • To display the location of routing matrix components and convert FPCs from T640 router local numbering to routing matrix global numbering, issue the show chassis location fpc command on the TX Matrix router:
      user@router> show chassis location fpc
      Global FPC    LCC     Local FPC
           1          0         1
           2          0         2
           3          0         3
          16          2         0
          17          2         1
          19          2         3
      
    • To check the status of the SIB connection between the TX Matrix router and T640 routers, issue the show chassis fabric topology command on the TX Matrix router. All values for each available T640 router (LCC) should be in the UP state. In the following excerpt of output for this command, a routing matrix that contains only LCCs 0 and 2 shows only these two T640 routers as being UP:
      LCC0_SIB-L0_F0,03->SIB-S0_F0,00 UP
      LCC1_SIB-L0_F0,03->SIB-S0_F0,01 RESET
      LCC2_SIB-L0_F0,03->SIB-S0_F0,02 UP
      LCC3_SIB-L0_F0,03->SIB-S0_F0,03 RESET
      
    • To verify that the Ethernet links between the TX Matrix router and the T640 router control boards are operational, issue the show chassis ethernet-switch command on the TX Matrix router:
      user@router> show chassis ethernet-switch
      scc-re0:
      --------------------------------------------------------------------------
      Link is good on FE port 4 connected to device: LCC0
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 6 connected to device: LCC2
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 8 connected to device: SPMB
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on GE port 13 connected to device: Other RE
        Speed is 1000Mb
        Duplex is full
        Autonegotiate is Enabled
      lcc0-re0:
      --------------------------------------------------------------------------
      Link is good on FE port 1 connected to device: FPC1
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 2 connected to device: FPC2
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 3 connected to device: FPC3
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 8 connected to device: SPMB
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 10 connected to device: SCC
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on GE port 13 connected to device: Other RE
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      lcc2-re0:
      --------------------------------------------------------------------------
      Link is good on FE port 0 connected to device: FPC0
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 1 connected to device: FPC1
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 3 connected to device: FPC3
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 8 connected to device: SPMB
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on FE port 10 connected to device: SCC
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      Link is good on GE port 13 connected to device: Other RE
        Speed is 100Mb
        Duplex is full
        Autonegotiate is Enabled
      

    Published: 2013-07-19