Technical Documentation
New
Documentation Search
jnxAtmVpTable
The jnxAtmVpTable extends the atmVplTable defined in RFC 2515, Definitions of Managed Objects for ATM Management, and contains additional information about ATM virtual paths (VP).
The jnxAtmVpTable, whose object identifier is {jnxAtm 3}, contains jnxAtmVpEntry. Each jnxAtmVpEntry, whose object ID is {jnxAtmVpTable 1}, contains the objects listed in Table 1.
Table 1: jnxAtmVpTable
Object | Object ID | Description |
|---|---|---|
jnxAtmVpEntry | jnxAtmVpTable 1 | Represents configuration status and statistics information related to an ATM VP. However, traffic stats are available per VP tunnel only if shaping is configured on the VP. You can use the jnxAtmVpFlags to determine whether shaping is enabled. Similarly, the values for OAM config and OAM stat objects are invalid (default value: 0) if no OAM is configured. You can use the jnxAtmVpFlags to determine whether OAM is configured. Note: For an ATM-1 VP, the only valid object is jnxAtmVpFlags. |
jnxAtmVpFlags | jnxAtmVpEntry 1 | Represents the flags associated with the VP. This object uses the following values:
|
jnxAtmVpTotalDownTime | jnxAtmVpEntry 2 | Represents the total downtime for the VP since the last reboot of the system. |
jnxAtmVpOamPeriod | jnxAtmVpEntry 3 | Indicates the frequency at which the OAM F4 cells are transmitted to find out the status of the VP. This object returns a value of zero if OAM is not enabled for the VP. |
jnxAtmVpOamUpCellCount | jnxAtmVpEntry 4 | Indicates the minimum number of consecutive loopback cells required to confirm that a VP is up. |
jnxAtmVpOamDownCellCount | jnxAtmVpEntry 5 | Indicates the minimum number of consecutive loopback cells required to confirm that a VP is down. |
jnxAtmVpInBytes | jnxAtmVpEntry 6 | Indicates the number of bytes received on the VP. |
jnxAtmVpOutBytes | jnxAtmVpEntry 7 | Indicates the number of bytes sent out of the VP. |
jnxAtmVpInPkts | jnxAtmVpEntry 8 | Indicates the number of packets received on the VP. |
jnxAtmVpOutPkts | jnxAtmVpEntry 9 | Indicates the number of packets sent out on the VP. |
jnxAtmVpInOamF4Cells | jnxAtmVpEntry 10 | Indicates the number of OAM F4 cells received on the VP. |
jnxAtmVpOutOamF4Cells | jnxAtmVpEntry 11 | Indicates the number of OAM F4 cells transmitted on the VP. |
jnxAtmVpInOamF4LoopCells | jnxAtmVpEntry 12 | Indicates the number of OAM F4 loopback cells received on the VP. |
jnxAtmVpOutOamF4LoopCells | jnxAtmVpEntry 13 | Indicates the number of OAM F4 cells transmitted on the VP. |
jnxAtmVpInOamF4RdiCells | jnxAtmVpEntry 14 | Indicates the number of OAM F4 RDI cells received on the VP. |
jnxAtmVpOutOamF4RdiCells | jnxAtmVpEntry 15 | Indicates the number of OAM F4 RDI cells transmitted on the VP. |
jnxAtmVpInOamF4AisCells | jnxAtmVpEntry 16 | Indicates the number of OAM F4 AIS cells received on the VP. |
