Configuring Application Protocol Properties

[ Contents] [ Prev] [ Next] [ Index] [ Report an Error]

To configure application properties, include the application statement at the [edit applications] hierarchy level:


            
               [edit applications]
               application application-name {
               
               application-protocol protocol-name;
               
               destination-port port-number;
               
               icmp-code value;
               
               icmp-type value;
               
               inactivity-timeout value;
               
               learn-sip-register;
               
               protocol type;
               
               rpc-program-number number;
               
               sip-call-hold-timeout seconds;
               
               snmp-command command;
               
               source-port port-number;
               
               ttl-threshold value;
               
               uuid hex-value;
               
               }

You can group application objects by configuring the application-set statement; for more information, see Configuring Application Sets.

This section includes the following tasks for configuring applications:

Configuring an Application Protocol

The application-protocol statement allows you to specify which of the supported application protocols (ALGs) to configure and include in an application set for service processing. To configure application protocols, include the application-protocol statement at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               application-protocol protocol-name;

Table 5 shows the list of supported protocols. For more information about specific protocols, see ALG Descriptions.

Table 5: Application Protocols Supported by Services Interfaces

Protocol Name	CLI Value	Comments
Bootstrap protocol (BOOTP)	bootp	Supports BOOTP and dynamic host configuration protocol (DHCP).
Distributed Computing Environment (DCE) remote procedure call (RPC)	dce-rpc	Requires the protocol statement to have the value udp or tcp. Requires a uuid value. You cannot specify destination-port or source-port values.
DCE RPC portmap	dce-rpc-portmap	Requires the protocol statement to have the value udp or tcp. Requires a destination-port value.
Domain Name System (DNS)	dns	Requires the protocol statement to have the value udp. This application protocol closes the DNS flow as soon as the DNS response is received.
Exec	exec	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
FTP	ftp	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
H.323	h323	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
Internet Control Message Protocol (ICMP)	icmp	Requires the protocol statement to have the value icmp or to be unspecified.
Internet Inter-ORB Protocol (IIOP) Transmission Control Protocol (TCP)	iiop	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
IP	ip	–
Login	login	–
NetBIOS	netbios	Requires the protocol statement to have the value udp or to be unspecified. Requires a destination-port value.
NetShow	netshow	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
RealAudio	realaudio	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
Real-Time Streaming Protocol (RTSP)	rtsp	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
RPC User Datagram Protocol (UDP) or TCP	rpc	Requires the protocol statement to have the value udp or tcp. Requires a rpc-program-number value. You cannot specify destination-port or source-port values.
RPC port mapping	rpc-portmap	Requires the protocol statement to have the value udp or tcp. Requires a destination-port value.
Session Initiation Protocol (SIP)	sip	For more information, see Configuring SIP.
Shell	shell	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.
SNMP	snmp	Requires the protocol statement to have the value udp or to be unspecified. Requires a destination-port value.
SQLNet	sqlnet	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port or source-port value.
Trace route	traceroute	Requires the protocol statement to have the value udp or to be unspecified. Requires a destination-port value.
Trivial FTP (TFTP)	tftp	Requires the protocol statement to have the value udp or to be unspecified. Requires a destination-port value.
WinFrame	winframe	Requires the protocol statement to have the value tcp or to be unspecified. Requires a destination-port value.

Note: You can configure application-level gateways (ALGs) for ICMP and trace route under stateful firewall, NAT, or CoS rules when twice NAT is configured in the same service set. These ALGs cannot be applied to flows created by the Packet Gateway Controller Protocol (PGCP). Twice NAT does not support any other ALGs. NAT applies only the IP address and TCP or UDP headers, but not the payload.

For more information about configuring twice NAT, see Network Address Translation Services Configuration Guidelines.

Configuring the Network Protocol

The protocol statement allows you to specify which of the supported network protocols to match in an application definition. To configure network protocols, include the protocol statement at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               protocol type;

You specify the protocol type as a numeric value; for the more commonly used protocols, text names are also supported in the command-line interface (CLI). Table 6 shows the list of the supported protocols.

Table 6: Network Protocols Supported by Services Interfaces

Network Protocol Type	CLI Value	Comments
IP Security (IPsec) authentication header (AH)	ah	–
External Gateway Protocol (EGP)	egp	–
IPsec Encapsulating Security Payload (ESP)	esp	–
Generic routing encapsulation (GR)	gre	–
ICMP	icmp	Requires an application-protocol value of icmp.
Internet Group Management Protocol (IGMP)	igmp	–
IP in IP	ipip	–
OSPF	ospf	–
Protocol Independent Multicast (PIM)	pim	–
Resource Reservation Protocol (RSVP)	rsvp	–
TCP	tcp	Requires a destination-port or source-port value unless you specify application-protocol rcp or dce-rcp.
UDP	udp	Requires a destination-port or source-port value unless you specify application-protocol rcp or dce-rcp.
Virtual Router Redundancy Protocol (VRRP)	vrrp	–

For a complete list of possible numeric values, see RFC 1700, Assigned Numbers (for the Internet Protocol Suite).

Note: IP version 6 (IPv6) is not supported as a network protocol in application definitions.

By default, the twice NAT feature can affect IP, TCP, and UDP headers embedded in the payload of ICMP error messages. You can include the protocol tcp and protocol udp statements with the application statement for twice NAT configurations. For more information about configuring twice NAT, see Network Address Translation Services Configuration Guidelines.

Configuring the ICMP Code and Type

The ICMP code and type provide additional specification, in conjunction with the network protocol, for packet matching in an application definition. To configure ICMP settings, include the icmp-code and icmp-type statements at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               icmp-code value;
               
               icmp-type value;

You can include only one ICMP code and type value. The application-protocol statement must have the value icmp. Table 7 shows the list of supported ICMP values.

Table 7: ICMP Codes and Types Supported by Services Interfaces

CLI Statement	Description
icmp-code	This value or keyword provides more specific information than icmp-type. Because the value’s meaning depends upon the associated icmp-type value, you must specify icmp-type along with icmp-code. For more information, see the JUNOS Policy Framework Configuration Guide. In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed). The keywords are grouped by the ICMP type with which they are associated: parameter-problem: ip-header-bad (0), required-option-missing (1) redirect: redirect-for-host (1), redirect-for-network (0), redirect-for-tos-and-host (3), redirect-for-tos-and-net (2) time-exceeded: ttl-eq-zero-during-reassembly (1), ttl-eq-zero-during-transit (0) unreachable: communication-prohibited-by-filtering (13), destination-host-prohibited (10), destination-host-unknown (7), destination-network-prohibited (9), destination-network-unknown (6), fragmentation-needed (4), host-precedence-violation (14), host-unreachable (1), host-unreachable-for-TOS (12), network-unreachable (0), network-unreachable-for-TOS (11), port-unreachable (3), precedence-cutoff-in-effect (15), protocol-unreachable (2), source-host-isolated (8), source-route-failed (5)
icmp-type	Normally, you specify this match in conjunction with the protocol match statement to determine which protocol is being used on the port. For more information, see the JUNOS Policy Framework Configuration Guide. In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed): echo-reply (0), echo-request (8), info-reply (16), info-request (15), mask-request (17), mask-reply (18), parameter-problem (12), redirect (5), router-advertisement (9), router-solicit (10), source-quench (4), time-exceeded (11), timestamp (13), timestamp-reply (14), or unreachable (3).

CLI Statement

Description

icmp-code

This value or keyword provides more specific information than icmp-type. Because the value’s meaning depends upon the associated icmp-type value, you must specify icmp-type along with icmp-code. For more information, see the JUNOS Policy Framework Configuration Guide.

In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed). The keywords are grouped by the ICMP type with which they are associated:

parameter-problem: ip-header-bad (0), required-option-missing (1)

redirect: redirect-for-host (1), redirect-for-network (0), redirect-for-tos-and-host (3), redirect-for-tos-and-net (2)

time-exceeded: ttl-eq-zero-during-reassembly (1), ttl-eq-zero-during-transit (0)

unreachable: communication-prohibited-by-filtering (13), destination-host-prohibited (10), destination-host-unknown (7), destination-network-prohibited (9), destination-network-unknown (6), fragmentation-needed (4), host-precedence-violation (14), host-unreachable (1), host-unreachable-for-TOS (12), network-unreachable (0), network-unreachable-for-TOS (11), port-unreachable (3), precedence-cutoff-in-effect (15), protocol-unreachable (2), source-host-isolated (8), source-route-failed (5)

icmp-type

Normally, you specify this match in conjunction with the protocol match statement to determine which protocol is being used on the port. For more information, see the JUNOS Policy Framework Configuration Guide.

In place of the numeric value, you can specify one of the following text synonyms (the field values are also listed): echo-reply (0), echo-request (8), info-reply (16), info-request (15), mask-request (17), mask-reply (18), parameter-problem (12), redirect (5), router-advertisement (9), router-solicit (10), source-quench (4), time-exceeded (11), timestamp (13), timestamp-reply (14), or unreachable (3).

Note: If you configure an interface with an input firewall filter that includes a reject action and with a service set that includes stateful firewall rules, the router executes the input firewall filter before the stateful firewall rules are run on the packet. As a result, when the Packet Forwarding Engine sends an ICMP error message out through the interface, the stateful firewall rules might drop the packet because it was not seen in the input direction.

Possible workarounds are to include a forwarding-table filter to perform the reject action, because this type of filter is executed after the stateful firewall in the input direction, or to include an output service filter to prevent the locally generated ICMP packets from going to the stateful firewall service.

Configuring Source and Destination Ports

The TCP or UDP source and destination port provide additional specification, in conjunction with the network protocol, for packet matching in an application definition. To configure ports, include the destination-port and source-port statements at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               destination-port value;
               
               source-port value;

You must define one source or destination port. Normally, you specify this match in conjunction with the protocol match statement to determine which protocol is being used on the port; for constraints, see Table 5.

You can specify either a numeric value or one of the text synonyms listed in Table 8.

Table 8: Port Names Supported by Services Interfaces

Port Name	Corresponding Port Number
afs	1483
bgp	179
biff	512
bootpc	68
bootps	67
cmd	514
cvspserver	2401
dhcp	67
domain	53
eklogin	2105
ekshell	2106
exec	512
finger	79
ftp	21
ftp-data	20
http	80
https	443
ident	113
imap	143
kerberos-sec	88
klogin	543
kpasswd	761
krb-prop	754
krbupdate	760
kshell	544
ldap	389
login	513
mobileip-agent	434
mobilip-mn	435
msdp	639
netbios-dgm	138
netbios-ns	137
netbios-ssn	139
nfsd	2049
nntp	119
ntalk	518
ntp	123
pop3	110
pptp	1723
printer	515
radacct	1813
radius	1812
rip	520
rkinit	2108
smtp	25
snmp	161
snmptrap	162
snpp	444
socks	1080
ssh	22
sunrpc	111
syslog	514
tacacs-ds	65
talk	517
telnet	23
tftp	69
timed	525
who	513
xdmcp	177
zephyr-clt	2103
zephyr-hm	2104

For more information about matching criteria, see the JUNOS Policy Framework Configuration Guide.

Configuring the Inactivity Timeout Period

You can specify a timeout period for application inactivity. If the software has not detected any activity during the duration, the flow becomes invalid when the timer expires. To configure a timeout period, include the inactivity-timeout statement at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               inactivity-timeout seconds;

The default value is 30 seconds. The value you configure for an application overrides any global value configured at the [edit interfaces interface-name service-options] hierarchy level; for more information, see Configuring Default Timeout Settings for Services Interfaces.

Configuring SIP

The Session Initiation Protocol (SIP) is a generalized protocol for communication between endpoints involved in Internet services such as telephony, fax, video conferencing, instant messaging, and file exchange. The supported standard is described in RFC 3261, SIP: Session Initiation Protocol, which includes stateful firewall and Network Address Translation (NAT) support for SIP dialogs and UDP IPv4 transport of SIP messages.

To implement SIP on adaptive services interfaces, you configure the application-protocol statement at the [edit applications application application-name] hierarchy level with the value sip. For more information about this statement, see Configuring an Application Protocol. In addition, there are two other statements you can configure to modify how SIP is implemented:

You can enable the router to accept any incoming SIP calls for the endpoint devices that are behind the NAT firewall. When a device behind the firewall registers with the proxy that is outside the firewall, the AS or Multiservices PIC maintains the registration state. When the learn-sip-register statement is enabled, the router can use this information to accept inbound calls. If this statement is not configured, no inbound calls are accepted; only the devices behind the firewall can call devices outside the firewall.
To configure SIP registration, include the learn-sip-register statement at the [edit applications application application-name] hierarchy level:

[edit applications application application-name] learn-sip-register;

You can also manually inspect the SIP register by issuing the show services stateful-firewall sip-register command; for more information, see the JUNOS System Basics and Services Command Reference.

You can specify a timeout period for the duration of SIP calls that are placed on hold. When a call is put on hold, there is no activity and flows might time out after the configured inactivity-timeout period expires, resulting in call state teardown. To avoid this, when a call is put on hold, the flow timer is reset to the sip-call-hold-timeout cycle to preserve the call state and flows for longer than the inactivity-timeout period.
To configure a timeout period, include the sip-call-hold-timeout statement at the [edit applications application application-name] hierarchy level:

[edit applications application application-name] sip-call-hold-timeout seconds;

The default value is 7200 seconds and the range is from 0 through 36,000 seconds (10 hours).

Configuring an SNMP Command for Packet Matching

You can specify an SNMP command setting for packet matching. To configure SNMP, include the snmp-command statement at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               snmp-command value;

The supported values are get, get-next, set, and trap. You can configure only one value for matching. The application-protocol statement at the [edit applications application application-name] hierarchy level must have the value snmp. For information about specifying the application protocol, see Configuring an Application Protocol.

Configuring an RPC Program Number

You can specify an RPC program number for packet matching. To configure an RPC program number, include the rpc-program-number statement at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               rpc-program-number number;

The range of values used for DCE or RPC is from 100,000 through 400,000. The application-protocol statement at the [edit applications application application-name] hierarchy level must have the value rpc. For information about specifying the application protocol, see Configuring an Application Protocol.

Configuring the TTL Threshold

You can specify a trace route time-to-live (TTL) threshold value, which controls the acceptable level of network penetration for trace routing. To configure a TTL value, include the ttl-threshold statement at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               ttl-threshold value;

The application-protocol statement at the [edit applications application application-name] hierarchy level must have the value traceroute. For information about specifying the application protocol, see Configuring an Application Protocol.

Configuring a Universal Unique Identifier

You can specify a Universal Unique Identifier (UUID) for DCE RPC objects. To configure a UUID value, include the uuid statement at the [edit applications application application-name] hierarchy level:


            
               [edit applications application application-name]
               
               uuid hex-value;

The uuid value is in hexadecimal notation. The application-protocol statement at the [edit applications application application-name hierarchy level must have the value dce-rpc. For information about specifying the application protocol, see Configuring an Application Protocol. For more information on UUID numbers, see http://www.opengroup.org/onlinepubs/9629399/apdxa.htm.

[ Contents] [ Prev] [ Next] [ Index] [ Report an Error]